CoolGear CG-10PU3MGD Manual de usuario
1
10 Port Managed USB 3.2 Gen 1 Hub w/
15KV
ESD Surge Protection
Model No. CG-10PU3MGD
Thank you for purchasing this 10-port Managed USB3.2 Gen 1 hub. The
Super-speed Hub is supplied with managing software utilities which can turn
on/off the bus power of each downstream device or even reset the entire hub by
user or application programs. It enables the success of your critical USB
applications instantly and improve your investment returns.
Features:
✓Compliant with USB Specification 3.2 Gen 1
✓Metal Case, DIN Rail and wall mountable
✓Software Manageable Bus power for each Port
✓Supports software utilities for Windows (XP and above), Linux
✓Provides 10 Downstream USB3.2 Gen 1 Facing Ports (see Note 1)
✓Provides 10 LEDs Indicating each bus power states
✓Supports 5Gbps (Super-speed), 480Mbps (High speed), 12Mbps (Full-speed)
and 1.5Mbps (Low-speed) Speed
✓Supports 15KV ESD Level 4 Protection for Each Port
✓Supports +7~24V DC Wide Range Input Power
✓Supports USB Battery Charging v1.2 : CDP, DCP modes
1. Introduction
10-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
2
1. USB-A Downstream Facing Port Connectors: There are 10 USB-A
connectors for standard USB3.2 Gen 1 and legacy USB2.0/1.1
devices.
Note 1: The last USB port (Port 10) of this hub does NOT
support USB2.0/1.1 devices because it is used to
communicate with the managing utilities. However, it still
supports USB3.2 Gen 1 devices.
2. USB-B Upstream Facing Port Connector: The Type-B connector
from upstream USB3.2 Gen 1 port. It is connected from host or
another USB3.2 hub’s downstream facing port.
3. Power LED: Turns on indicates the hub was powered.
4. Port State Indicator LEDs: Each port has a LED next to it. When the
LED is on, the USB device is enabled (connected). If the LED is off, the
USB device is disabled (disconnected).
5. Self Power Input Connector: This 2-pin (one pin is for the positive
voltage and the other pin is GND) terminal blocks is used to connect
2. Connector Layout
Power LED
10 USB-A Downstream Ports
USB-B Upstream
Port Connector
Power Input
Connector
10 Port On/Off State LED Indicators
10-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
3
wide range power source to self-power the hub, the voltage can be in
the range from +7V to 24V DC.
1. Use static electricity discharge precautions.
Remove possible static discharge potential from any objects that the
hub may come in contact with before installation. This can be
accomplished by touching a bare metal chassis rail after you have
turned off the power.
2. Apply DC power (range from +7V to 24V) to the 2-pin Terminal
Block Connector.
Warning!!
Please make sure the polarity of the input power should
correctly match the terminal block pins
3. Connecting USB Host cable: The host cable can be a standard
B-to-A or B-to-C USB3.2 Gen 1 cable (depends on the host port’s
connector type). Please connect the type-A (or Type-C) end
connector of the cable to your USB host port, then connect the
type-B end connector to this hub. Since the USB hub is
plug-and-play, you don’t have to turn off your host computer when
installing the hub.
4. Connect the USB devices to the downstream ports of this hub.
3. Hardware Installation
-+7~24V
-GND
+
-
10-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
4
5. Mount your hub on the wall or DIN RAIL if required.
6. Install the USB Hub Administrator Utilities as described in the
following chapter
The Hub supports managing utilities called USB Hub Administrator for
major recent Windows (XP and above) and Linux:
1. The above folders include the software for different
platforms. If you are installing it on Windows, please find the
executable setup program in Windows folder, double-click it:
4. USB Hub Administrator Utilities Installation
DIN RAIL Clip
Wall mounting
holes
10-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
5
2. Please follow the on-screen instructions of the setup
program to complete the installation. After installed, it will
launch the utility automatically:
⚫Click Auto Search to find all Managed USB Hubs
⚫Click the item on the list to select the Hub to control
⚫Click on the numeric (indicate the Port number) button to
turn On/Off the USB port
⚫You can save the current port states by clicking the Save
Port States button
10-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
6
3. To use the console utility CUSBC to control the USB devices,
please run Command Prompt as follows:
To see all CUSBC commands, type:
CUSBC /?
10-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
7
To query all Hubs connected:
CUSBC /Q
To perform a factory reset:
1. Verify that your hub’s Power LED is off.
2. On the side of your hub, locate the hole of the Restore Factory
Settings button:
3. Use a paper clip or similar object to press and hold the Restore
Factory Settings button, while still holding the button power on the
hub.
4. Release the Restore Factory Settings button.
5. Restore to Factory Settings
Restore Factory
Settings button
10-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
8
5. Your hub resets to its factory default settings:
⚫All ports are On
⚫The password: pass
10-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
9
Operating temp.: 0 to 55C (32 to 131F)
Operating humidity: 5 to 95% RH
Dimensions (LxWxH): 197.7x55.5x31.0 mm
(7.78 x 2.18 x 1.22 in)
6. Environmental Specifications
Tabla de contenidos
Otros manuales de Cambiar de CoolGear
CoolGear
CoolGear USBG-12U2ML Manual de usuario
CoolGear
CoolGear CG-7PU3MGD Manual de usuario
CoolGear
CoolGear CG-U31iS4PH Manual de usuario
CoolGear
CoolGear USBG-10XU1 Manual de usuario
CoolGear
CoolGear CG-7U3DS Manual de usuario
CoolGear
CoolGear USBG-12U2ML Manual de usuario
CoolGear
CoolGear USBG-3X4M Manual de usuario
CoolGear
CoolGear USBG-4U2ML Manual de usuario
CoolGear
CoolGear USBG-4PUSB2-MH Manual de usuario
CoolGear
CoolGear USBG-7DU2 Manual de usuario
CoolGear
CoolGear USBG-7DU2 Manual de usuario
CoolGear
CoolGear USBG-7DU2S Manual de usuario
CoolGear
CoolGear USBG-7U3ML Manual de usuario
CoolGear
CoolGear CG-7PU313C Manual de usuario
CoolGear
CoolGear USBG-7U2ML Manual de usuario
CoolGear
CoolGear USB3-16U1 Manual de usuario
CoolGear
CoolGear USBG-4U3ML Manual de usuario
CoolGear
CoolGear CG-7PU31HB Manual de usuario
CoolGear
CoolGear USBG-4U3MLR2 Manual de usuario
CoolGear
CoolGear CG-16PU31H Manual de usuario
