Connects2 CTSBM011.2 Manual de usuario
www.connects2.com
CTSBM011.2
BMW Steering Wheel Control Interface
BMW Mini R53 with Harmon Kardon Amp Retention
INSTRUCTION MANUAL
www.connects2.com
2
ABOUT THIS PRODUCT...
CTSBM011.2
BMW steering wheel control interface for BMW Mini R53 with Harmon Kardon Amp
Product Contents
- Interface
- Harness
- Instruction
Application
BMW Mini R53
Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installa-
tion. The place of installation must be free of moisture and away from heat sources.
Please ensure you use the correct tools to avoid damage to the vehicle or product.
Connects2 can not be held responsible for the installation of this product.
Technical Support
Connects2 want to provide a fast and suitable resolution should you encounter any
technical issues. With this in mind, when contacting Connects2, try to provide as
much Information as possible. This will speed up the process and help us to help you.
Please use our dedicated online technical support centre: support.connects2.com
Subscribe to our YouTube Channel for installation
guides and tips... www.youtube.com/connects2
1. Interface
2. Male Power/Speaker ISO connector
3. Vehicle Specic Connector
4. Amp Control Button
1
2
3
4
www.connects2.com
3
FITTING GUIDE
1. Remove and disconnect the original head unit.
2. Connect the 12 way molex connector of the head unit patch lead
(supplied separately) to the interface.
3. Connect the opposite end of head unit patch lead to the head unit steering
wheel control input on the back of the aftermarket head unit. This may be a
3.5mm jack plug or a wire input depending upon the head unit brand being
tted. Please see the head unit installation manual for further information on
where to connect.
Important Note: This step must be completed before connecting power to the
interface. Failure to so do may result in no steering wheel control function.
4. Connect the 14 way molex connector to the interface.
www.connects2.com
4
FITTING GUIDE
5. For vehicles without source button, install control button on dashboard.
6. Connect the male power/speaker harness to the female power/speaker
harness from the aftermarket head unit. Test head unit for correct operation.
www.connects2.com
5
FITTING GUIDE
For aftermarket head units which do not have an ISO connector the interface
uses the following wiring colours:
Steering Wheel Control Functions
Wire Colour Function
Yellow Permanent 12V
Black Ground
Red 12V Ignition
Orange Illumination
Blue Antenna Remote
Pink Speed Pulse
Green Park Brake
Purple Reverse
Pink/Black Telephone Mute
Wire Colour Function
Purple Right Rear Speaker +
Purple/Black Righ Rear Speaker -
Green Left Rear Speaker +
Green/Black Left Rear Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
White Left Front Speaker +
White/Black Left Front Speaker -
Volume +
Track +Track -
Volume -
STEERING WHEEL CONTROL FUNCTIONS
www.connects2.com
6
OPERATING INSTRUCTIONS
Operation for vehicles with steering wheel controls
(vehicle must have Source button)
To enter amplier adjustment mode press and hold Source button for more
than 3 seconds. When In amplier adjustment mode the steering wheel
controls no longer control the head unit.
Front/Rear Balance Adjustment
Press & hold Vol + button to cycle from front to rear and back to front again.
Release button when the desired setting is achieved.
Driver Mode
To enable/disable Driver mode press Track +
Preset EQ
Press Track – to cycle through Normal, Spacial, Electronic, Instrumental & Festi-
val EQ settings.
To return the steering wheel controls to normal operation press Vol –
www.connects2.com
7
OPERATING INSTRUCTIONS
Operation for vehicles without steering wheel controls
Front/Rear Balance Adjustment
Press & hold control button for more than 3 seconds to cycle from front to rear
and back to front again. Release button when the desired setting is achieved.
Driver Mode
Press and hold control button for more than 1 second (but no longer that 3
seconds to avoid changing F/R Balance) to toggle Driver mode off/on
Preset EQ
A short press of the control button will change the various Preset EQ settings
from Normal, Spacial, Electronic, Instrumental & Festival
Save settings
The interface will save all changes to its internal memory when the ignition is
switched off. The settings will not be lost if power is disconnected.
www.connects2.com
8
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Connects2
Connects2
Connects2 CT51-MC03 Manual de usuario
Connects2
Connects2 CAM-35 Manual de usuario
Connects2
Connects2 adaptiv mini ADVM-BM1 Manual de usuario
Connects2
Connects2 CAM-32 Manual de usuario
Connects2
Connects2 4X4ALTIMETER Guía de solución de problemas
Connects2
Connects2 CAM-AR1-AD Manual de usuario
Connects2
Connects2 CTUAR01 Manual de usuario
Connects2
Connects2 CAM-KIT12 Manual de usuario
Connects2
Connects2 CT23MB25/L Manual de usuario
Connects2
Connects2 CAM-55 Manual de usuario
Connects2
Connects2 Vision CAM-FT6 Manual de usuario
Connects2
Connects2 Aerpro CAKI01 Manual de usuario
Connects2
Connects2 CAN-Connect CANHBJP1 Manual de usuario
Connects2
Connects2 CT23SK05 Manual de usuario
Connects2
Connects2 Gator G162V Manual de usuario
Connects2
Connects2 CT51-BM06 Manual de usuario
Connects2
Connects2 Vision CAM-4 Manual de usuario
Connects2
Connects2 Aerpro CAKI01 Manual de usuario
Connects2
Connects2 CT23CT11 Manual de usuario
Connects2
Connects2 CAM-MB13 Manual de usuario
