CONCORD DVX Manual de usuario
DVx
CONCORD
Quick Start Guide
LANGUAGES
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
NEDERLANDS
PORTUGUÊS
DZ QSG(515815-00)-E 1 11/15/04, 1:35:04 PM
1
ENU
QUICK START GUIDE
1
This Quick Start Guide provides a quick reference for operating your
new Camera. Refer to the User’s Guide, which can be found on the
CD-ROM, for detailed instructions on how to use all of your camera’s
features. Before using the camera, make sure to read all safety
instructions and precautions outlined in the User’s Guide.
DZ QSG(515815-00)-E 1 11/15/04, 1:35:04 PM
ENU
LOADING THE BATTERY
The camera uses a 3.7 volts rechargeable Li-ion Battery.
1. Press the Battery Door Latch that is located at the upper side of the unit to open the back cover.
2. Slide the battery into the battery compartment and align with the metal contact.
3. Replace the back cover.
CHARGING THE BATTERY
Charging by AC-Adapter
1. Plug the AC end of the adaptor into a standard AC socket.
2. Plug the USB end of the adaptor into the USB port of the
camera. The red backlight will be turned on.
• Charging the battery for the first time will takes about 6
hours. When the battery is fully charged, the red
backlight will go off.
• Charging the battery fully for the second time or later will
take at least 2 hours.
• When charging the battery for the first time, it is
recommended to use AC adaptor instead of USB cable.
Charging by PC / Notebook
You can also use the USB cable to charge the battery.
1. Connect the bigger end of the USB cable to the USB port of your PC
or Notebook.
2. Plug the smaller end of the USB cable to the USB port of the camera.
• The red backlight will turn on when the battery is being charged
and it will turn off when the unit is fully charged. The time for fully
charging is about 4-6 hours.
INSTALLING THE MEMORY CARD
The camera uses SD or MMC card as storage. Insert an SD or MMC
card according to the illustrations below before proceeding to take video
clips or pictures.
To remove the memory card, gently push the edge of the memory card
with your fingertip to eject it first, and then pull the card out.
1
2
3
AC end USB end
2
DZ QSG(515815-00)-E 2 11/15/04, 1:35:05 PM
ENU
POWER ON /OFF
Power On
Press the Power button for more than 1 second to turn on the
Camera. The LCD will be turned on.
Power Off
Press the Power button for more than 1 second.
Caution:
1. If the Power button is pressed for more than 1 second while
data is being written to the memory card, the Camera will shut
down, but the memory writing will continue until it is finished.
2. If the Power button is pressed for more than 1 second while the
camera can’t be turned on, that may because the battery is over.
Charge the battery and then try again.
SETTING THE CAMERA’S OPERATIONAL MODES
1. Press the MODE button repeatedly to switch among the 7 modes. The mode selected will be highlighted on
the screen.
• You can also press the MODE button first, then press the , , or button to select the desired mode.
DV: Use this mode to record video clip.
DSC: Use this mode to take still picture.
MP3: Use this mode to play MP3 music.
VR: Use this mode to record audio clip.
PLAY: Use this mode to view the recorded video clips, pictures or audio clips.
SET UP: Use this mode to adjust the camera settings.
LIGHT: Use this mode to take the camera as a flashlight.
2. Press the SET button to enter the selected mode.
SETTING LANGUAGE
1. Power on the camera and switch to SETUP mode.
2. Press the or button to highlight the Language.
3. Press the button or SET button to enter its submenu.
4. Press the or button to select the desired language.
5. Press the SET to save the setting. Or press the button to exit the
submenu. If so, the language setting will not be changed.
SETTING DATE AND TIME
1. Power on the camera and switching to SETUP mode.
2. Press the or button to highlight the Set Date or Set Time.
3. Press the button or SET button to enter its submenu.
4. Press the or button the highlight the field to be changed.
5. Press the or button to change the value of the selected field.
6. Press the SET to save the setting.
7
4
5
6
Power
Button
Shutter
button
DISPLAY
button
MENU button
SET
button
3
DZ QSG(515815-00)-E 3 11/15/04, 1:35:06 PM
ENU
FORMATTING MEMORY CARD
To ensure your memory card functions properly, it is recommended to format the memory card for the first time
you use it.
Caution: Formatting will delete all files including the protected files from the memory.
1. Power on the camera and switch to SETUP mode.
2. Press the or button to highlight the Format.
3. Press the button or SET button to enter its submenu.
4. Press the or button to select Yes or No.
5. Press the SET to confirm.
• If Yes is selected, all the files in the memory will be deleted.
• If No is selected, no change will be made.
RECORDING A VIDEO CLIP
1. Power on the Camera and enter DV mode.
2. Rotate the Lens to frame the subject.
3. Press the Shutter button to start recording. The recording
time are indicated on the screen.
4. Press the Shutter button again to end the video recording.
TAKING STILL PICTURES
1. Power on the Camera and enter DSC mode.
2. Rotate the Lens to frame the subject.
• For best results, stand at least 0.8 m (2.62 ft.) away from
the subject.
3. Press the Shutter button to take your picture.
SELF-PHOTOGRAPHY
1. Power on the camera and switch to DV/DSC mode.
2. Turn the lens to face yourself.
3. Press the button to reverse the image on the LCD.
4. Press the Shutter button to take the pictures or video clips of yourself.
8
9
10
Remainin
g
time
Exposure
Value
Battery
Video
Size
DV Mode
11
Remainin
g
Pictures
Exposure
Value
Battery
shutter
Speed
Picture Size
DSC Mode
Self-Photography
4
DZ QSG(515815-00)-E 4 11/15/04, 1:35:09 PM
ENU
USING THE DIGITAL ZOOM
The camera provides up to 4x digital zoom.
1. Press the button to zoom in the subject. The zoom scales will be shown on the LCD.
2. Press the button to zoom out.
SETTING THE FLASH FOR PICTURE TAKING
Press the button repeatedly until the desired flash icon appears on the LCD to set the flash mode.
Auto ( ): The camera judges automatically if a Flash is required. If the environment is dark, the flash will
fire. The camera uses auto flash by default.
Flash On ( ): The flash will fire in any lighting condition.
Flash Off ( ): The Flash will not fire in this mode.
Note:
1. The flash provides assisting light only. If environment is too dark, the flash cannot ensure enough exposure
for taking clear pictures.
2. When the battery is about to run out, the Flash Off icon ( ) will be shown on the screen and the flash will
not be available in this case.
SETTING PICTURE/VIDEO RESOLUTION
Resolution determines the size of a captured file. Higher resolution images contain more details and have larger
file sizes.
1. Press the MENU button to enter Menu screen.
2. Press the or button to highlight the Size.
3. Press the button or SET button to enter its submenu.
4. Press the or button to select the desired resolution setting.
5. Press the SET to save the setting.
6. Press the MENU to exit Menu screen.
SETTING PICTURE/VIDEO QUALITY
The quality setting determines the amount of compression used to reduce the
size of the stored files in order to economize space in the memory.
1. Press the MENU button to enter Menu screen.
2. Press the or button to highlight the Quality.
3. Press the button or SET button to enter its submenu.
4. Press the or button to select the desired quality setting.
5. Press the SET to save the setting.
6. Press the MENU to exit Menu screen.
13
14
15
5
12
DZ QSG(515815-00)-E 5 11/15/04, 1:35:11 PM
ENU
PLAYING MP3
1. Connect the camera to your computer by using the supplied USB cable and drag the desired MP3 files from your
computer into the \\Removable Disk\DCIM\100-DVx folder. Then disconnect the camera with the computer.
Note: You may also use card reader to save MP3 files onto memory card. But as the camera recognizes only
MP3 files saved in \\DCIM\100-DVx \ folder, you must format the memory card by using the camera first.
2. Power on the camera and switching to MP3 mode.
3. Press the or button to select songs.
4. Press the or button to adjust volume.
• The volume is divided into 21 levels (from 00 to 20).
5. Press the SET button to play the selected song.
6. Press the SET button to pause. Press the SET button again to resume playing.
RECORDING AND PLAYING VOICE FILES
1. Power on the camera and switch to VR mode.
2. Press the Shutter button to start recording.
3. Press the Shutter button again to end recording.
4. Press the or button to select a voice file.
5. Press the SET button to start playing the voice file.
6. Press the or button to adjust volume.
7. Press the SET button to pause. Press the SET button again to resume playing.
17
Volume
Repeat the
selected song
A B Repeat
Time
File Number
Battery
LCD on/off
Menu
5 Way
Function Key
MP3 Mode
Volume
Time
File Number
Battery
LCD on/off
Menu
5 Way
Function Key
VR Mode
Displaying Bar
Recording
Remaining tim
e
to record
6
16
DZ QSG(515815-00)-E 6 11/15/04, 1:35:12 PM
ENU
REVIEW THE STORED VIDEO CLIPS, PICTURES OR VOICE FILES
1. Power on the camera and switching to PLAY mode.
2. Press the or button to skip to the previous or next files.
3. If it is video clips or voice files,
• Press the SET button to start play. Press SET button again to pause or to resume playing.
• Press the or button to adjust volume.
DELETING FILES
1. Power on the camera and switch to PLAY mode.
2. Press the or button to find out the unwanted file.
3. Press the MENU button to enter Menu screen.
4. Press the or button to highlight Delete.
5. Press the button or SET button to enter its submenu.
6. Press the or button to select Yes or No.
7. Press the SET to confirm.
• If Yes is selected, the file will be deleted.
• If No is selected, no change will be made. Press the MENU to exit
Menu screen.
Note: Once the file is deleted, it cannot be recovered.
LOCKING THE FILES
To prevent accidental deletion of the files you like, you can lock the files by following steps below:
1. Power on the camera and switch to PLAY mode.
2. Press the or button to find out the file to be protected.
3. Press the MENU button to enter Menu screen.
4. Press the or button to highlight Lock.
5. Press the button or SET button to enter its submenu.
6. Press the or button to select Yes or No.
7. Press the SET to confirm.
• If Yes is selected, the file will be locked. The lock icon ( ) will
appear on the right side of the LCD.
• If No is selected, no change will be made. Press the MENU to exit
Menu screen.
7
20
19
18
Play Mode
Video
Picture
Voice
Previous
Files
Play/Pause
9-files displa
y
ed format
Volume
Next File
Battery
Number of File/All Files
DZ QSG(515815-00)-E 7 11/15/04, 1:35:13 PM
8
ENU
USING THE FLASHLIGHT
1. Power on the camera and switch to LIGHT mode.
2. Press the SET button to turn the flashlight on or off.
3. Press the button to increase the brightness. There are three levels of intensity.
4. Press the button to reduce the brightness.
DOWNLOADING FILES ONTO YOUR COMPUTER
Note for Windows 98 SE users: The camera driver must be installed first.
Note for all Windows users: The Windows Media Player 9 must be preinstalled before proceeding to view the
video clips on your computer.
For Windows Users
1. Connect the camera to the computer.
2. Double click “My Computer”.
3. Double click “Removable Disk”.
4. Double click “DICM”.
5. Double Click “100-DVx”.
• The pictures (JPEG), video clips (ASF), voice file (WAV) and MP3 files stored in the memory card will be
displayed.
6. Drag and drop the image you want to save in the computer.
• To select all files, click Edit > Select all.
For Macintosh Users
1. Connect the camera to the computer.
• After a few moments, the external hard drive will appear on the desktop.
2. Double-click the “Concord” removable drive that is on your desktop.
3. Double-click DCIM.
4. Double Click “100-DVx”.
• The pictures (JPEG), video clips (ASF), voice file (WAV) and MP3 files stored in the memory card will be
displayed.
5. Drag and drop the image you want to save in the computer.
• To select all files, click Edit > Select all.
Note: You may also transfer the stored pictures and video clips on your memory card onto your computer by
using a memory card reader (sold separately).
Concord and the Concord logo are registered trademarks or trademarks of Concord Camera Corp., in the United
States and/or other countries. Microsoft, Windows Media Player and Windows are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries. Mac and Macintosh are
registered trademarks or trademarks of Apple Computer, Inc. in the U.S. and other countries. All other brands
and product names are either registered trademarks or trademarks of their respective owners.
22
21
DZ QSG(515815-00)-E 8 11/15/04, 1:35:15 PM
Otros manuales para DVX
1
Tabla de contenidos
Idiomas:
Otros manuales de Cámara digital de CONCORD
CONCORD
CONCORD Eye-Q Go 2000 Manual de usuario
CONCORD
CONCORD Eye-Q Ir Manual de usuario
CONCORD
CONCORD Eye-Q Go Wireless Manual de usuario
CONCORD
CONCORD EYE-Q DUO Manual de usuario
CONCORD
CONCORD EYE-Q DUO 2000 Guía de instalación
CONCORD
CONCORD Eye-Q Go 2000 Manual de instrucciones
CONCORD
CONCORD Eye-Q DV Cam Manual de instrucciones
CONCORD
CONCORD Eye-Q 3X Manual de instrucciones
CONCORD
CONCORD VGA Manual de usuario
CONCORD
CONCORD Eye-Q 2040 Manual de usuario
CONCORD
CONCORD 3045Z Guía de instalación
CONCORD
CONCORD Eye-Q Go Wireless Manual de usuario
CONCORD
CONCORD Eye-Q 3340z Manual de instrucciones
CONCORD
CONCORD 3045 Manual de instrucciones
CONCORD
CONCORD Eye-Q 3120 Manual de usuario
CONCORD
CONCORD Eye-Q Go Wireless Manual de usuario
CONCORD
CONCORD PZ2180 AF Manual de usuario
CONCORD
CONCORD Eye-Q 2100 Manual de instrucciones
CONCORD
CONCORD Eye-Q 3040AF Manual de usuario
CONCORD
CONCORD QC3914 Manual de usuario
