Comtrol ROCKETLINX ES8510 Manual de usuario

QUICK INSTALLATION GUIDE

2000515 Rev G | Release Date - October 2016

ROCKETLINX ES8510

ES8510 | ES8510-XT | ES8510-XTE

INTRODUCTION

The RocketLinx ES8510, ES8510-XT, and ES8510-XTE are managed industrial

Ethernet switches with:

• Seven 10/100BASE-TX ports

• Three combo RJ45/SFP ports

• ES8510/ES8510-XT: 10/100BASE-TX (RJ45) or 100BASE-FX/

1000BASE-SX/LX/LHX/XD/ZX (SFP) Gigabit ports (standard mini GBIC

SFPs)

• ES8510-XTE: 10/100BASE-TX (RJ45) or 100BASE-FX (SFP) ports

(standard mini GBIC SFPs)

When the SFP is acve and installed, the corresponding RJ45 port is

deacvated. For example, if an SFP is installed and acve on the SFP Port 8,

the corresponding RJ45 Port 8 becomes inacve.

The ES8510 is encased with a rugged aluminum housing for industrial

environments:

• ES8510 provides a wide operang temperature

• ES8510-XT/ES8510-XTE are NEMA TS2 cered and provide an extended

operang temperature

The ES8510, ES8510-XT, and ES8510-XTE are referred to as the ES8510 unless

there is a dierence between the models.

See the Comtrol website for complete product specicaons.

INSTALLATION OVERVIEW

If you need more detailed installaon and conguraon informaon, you

can download the appropriate User Guide, which can be located at hp://

downloads.comtrol.com

Wiring the Power Inputs

The ES8510 provides redundant power, reverse polarity protecon, and

accepts a posive or negave power source but PW1 and PW2 must apply

to the same mode. The ES8510 can be congured to signal an alarm for loss

of power in either PW1 or PW2 using the web interface or Command Line

Interface (CLI).

Note: Power should be disconnected from the power supply before connecng it to

the switch. Otherwise, your screwdriver blade can inadvertently short your terminal

connecons to the grounded enclosure.

1. Insert the posive and negave wires into PW+ and PW- contacts

(PW1 and PW2). You can connect a single power supply or two power

supplies depending on your requirements.

2. If both power inputs are connected, the ES8510 is powered from the

highest connected voltage.

• ES8510/ES8510-XT: 12 to

48VDC.

• ES8510-XTE: 10 to 60VDC.

The Power 1/2 LEDs turn

red during the boot cycle

and change to green when

the ES8510 is ready.

3. Tighten the wire-clamp

screws to prevent the wires

from being loosened.

Wiring the Alarm Relay Output

The ES8510 provides two digital

inputs and two digital outputs

(dry relay output) on terminal

block connectors on the boom of the unit. Fault condions can be

congured in the web interface or Command Line Interface (CLI).

The Digital Input pin

can be pulled high or

low so that the

connected equipment

can acvely drive these

pins. The web interface

allows you to read and

set the value to the

connected device.

The power input voltage

of logic low is 0 to 10VDC

and logic high is 11 to

30VDC. Do not apply a

higher voltage than the

specicaon; it may cause

internal circuit damage

or cause an incorrect DI

acon.

Digital output relay contacts are energized (open) for normal operaon and

close for fault condions. The digital output relay contacts support up to 1A

at 24VDC. Do not apply voltage and current higher than the specicaons.

1. Insert the posive and negave wires (12-24 AWG) into V+ and V-.

2. Tighten the wire-clamp screws to prevent the wires from coming loose.

Mounng the ES8510

You can mount the ES8510 onto a DIN rail or oponally a panel or wall.

Follow the steps below to install the ES8510 with the

wall mounng plate:

1. To remove the DIN rail clip from the ES8510,

loosen the screws from the DIN rail clip.

2. Place the wall mounng plate on the rear

panel of the ES8510.

3. Use the screws to aach the wall mounng

plate to the ES8510.

4. Use the hook holes at the corners of the wall

mounng plate to hang the ES8510 onto the wall.

Connecng Ethernet Ports

Connect one end of an Ethernet cable into the Ethernet port of the ES8510

and the other end to the aached networking device. The Ethernet ports

support 10/100Mbps half/full-duplex. All ports auto-detect the signal from

connected devices to negoate the link speed and duplex mode. Auto MDI/

MDIX allows users to connect another switch, hub, or workstaon without

changing straight through or crossover cable.

Link/Act LED are lit to indicate trac and link status. See the LED subsecon

for more informaon.

Always make sure that the cables between the switches and aached devices

(for example, switch hub, or workstaon) are less than 100 meters (328 feet).

• 10BASE-T: Category 3, 4, or 5 cable

• 100BASE-TX/1000BASE-TX: Category 5 or 5e cable

Connecng the SFP Transceivers

To ensure system reliability, Comtrol recommends using Comtrol cered SFP

transceivers.

1. Plug the SFP transceiver into the SFP port.

2. Connect the transmit channel to the receive channel at each end.

3. Check the direcon/angle of the ber transceiver and the ber cable.

Note: This is a Class 1 Laser/LED product. Do not stare at the Laser/LED beam.

The SFP port does not funcon unl the ber cable is linked to another acve

device. The SFP and corresponding RJ45 ports work in an exclusive mode.

Trac sent or received through

the SFP module has priority thus

no trac is sent or received over

the corresponding RJ45

connecon. To use the RJ45

connecon, remove the

corresponding SFP.

Mul-Mode cables should not

exceed 2KM and Single-Mode cables should not exceed 30km.

PROGRAMMING THE IP ADDRESS

Congure the IP address using one of the following methods:

• PortVision DX (hp://downloads.comtrol.com)

• Web browser

• Telnet

• Command line interface (CLI) using the RS-232 console cable

The easiest way to congure a stac IP address for your network in

the ES8510 is to use a Windows host and PortVision DX (see below).

For informaon about using other conguraon methods, refer to the

appropriate

RocketLinx ES8510 User Guide.

The following procedure uses PortVision DX to program network sengs.

1. Install PortVision DX on a host system with a Windows operang system.

If you need assistance installing PortVision DX, see the appropriate

RocketLinx ES8510 User Guide.

2. Start PortVision DX. PortVision DX can be started from Start --> All

Programs --> Comtrol --> PortVision DX.

3. Click the Scan buon.

4. Select the Comtrol product families that you want to locate and click the

Scan buon.

5. Right-click the ES8510 in the Device List pane (lower) that you want to

congure and click Properes.

6. Enter a user-friendly Device Name.

7. Oponally, enter the ES8510 serial number, which displays a friendly

device name in the

Device List

pane on the main page.

8. Select DHCP IP or Stac IP for the

IP Mode

• If you select DHCP IP, go to Step 9.

• If you select Stac IP, enter an IP address, Subnet Mask, and

Default Gateway value for your network.

9. Oponally, select the appropriate Network Topology, which is an

informaonal eld.

10. Click the Apply Changes buon.

11. Click Close to return to the main screen.

12. You are now ready to congure the ES8510 features.

FEATURE CONFIGURATION

The ES8510 provides both in-band and out-band conguraon methods:

Out-band management means that you congure the ES8510 using the

RS-232 console cable and the Command Line Interface (CLI) to access the

ES8510 without aaching an admin PC to the network. You can also use

out-bound management, if you lost the network connecon to the

ES8510.

In-band management means that you connect remotely using the ES8510 IP

address through the network. You can remotely connect with the

ES8510 web interface or a Telnet console and the CLI.

The following procedure uses a web browser to congure ES8510

features. Refer to the appropriate

RocketLinx ES8510 User Guide

for other

conguraon methods.

1. Open a web browser and enter the IP address of the ES8510.

2. Enter admin for both the user name and the password when prompted.

3. Use the web interface to congure your device as needed for your

network.

You can use the help system or the appropriate User Guide for informaon

about conguring other ES8510 features.

LED INDICATORS

You can also view the LEDs for the ES8510 through the web interface using

the Device Front Panel page.

LEDs LED On LED Blinking LED O

Power 1, Power 2 Green: Power available Not applicable No power

DO1, DO2 Red: DO acvated Not applicable DO not acvated

DI1, DI2 Green: DI acvated Not applicable DI not acvated

R. M. (ring master) Green: working as ring

master

Green: ring failed Ring funcon disabled

or ES8510 is on a ring

but not the ring master

1 - 7 Green: Linked to another

device

Amber: Full-Duplex

Green: Acve trac Not connected

Collision

8 - 10

SFP

RJ45

Green: Connected

Green: Acve connecon

Plugged in but not

linked up

Not connected

COMTROL CUSTOMER SERVICE

You can use one of the following methods to contact Comtrol.

Contact Method Web Address or Phone Number

Support hp://www.comtrol.com/support

Downloads hp://downloads.comtrol.com/html/default

Website hp://www.comtrol.com

Phone +1 763.957.6000

Link/

Speed

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Comtrol

Comtrol

Comtrol RocketLinx ES8520-XT Manual de usuario

Comtrol

Comtrol RocketPort RPUSBSH Manual del operador

Comtrol

Comtrol RocketPort Manual de lista de piezas

Comtrol

Comtrol ROCKETLINX ES7206-XT Manual de usuario

Comtrol

Comtrol RocketLinx ES8108 Manual de usuario

Comtrol

Comtrol Rocket linx ES8508 Manual de usuario

Comtrol

Comtrol ROCKET LINX ES7506 Manual de usuario

Comtrol

Comtrol RocketLinx ES8108 Manual de usuario

Comtrol

Comtrol RocketLinx ES7506 Manual de usuario

Comtrol

Comtrol RocketLinx ES8108 Manual de usuario

Comtrol

Comtrol ROCKETLINX ES7105 Manual de usuario

Comtrol

Comtrol ROCKETLINX ACS7106 Manual de usuario

Comtrol

Comtrol DeviceMaster DM-2000 Series Manual del operador

Comtrol

Comtrol Rocketlinx ES8108-GigE Manual de usuario

Comtrol

Comtrol RocketLinx ES7528 Manual de usuario

Comtrol

Comtrol ROCKETLINX ES8508 Manual de usuario

Comtrol

Comtrol RocketLinx ES8105 Manual de usuario

Comtrol

Comtrol ROCKETLINX ES7510-XT Manual de usuario

Comtrol

Comtrol RocketLinx MP1204-XT Manual de usuario

Comtrol

Comtrol RocketPort Serial Hub Si Manual del operador

Comtrol

Comtrol RocketPort Manual del operador

Comtrol

Comtrol RocketLinx ES7510 Manual de usuario

Comtrol

Comtrol ROCKET LINX MP1204-XT Manual de usuario

Comtrol

Comtrol ROCKETLINX ES7110-VB Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario