Comtrol ROCKET LINX ES7506 Manual de usuario
QUICK INSTALLATION GUIDE
2000528 Rev D | Release Date - January, 2014
ROCKETLINX ES7506
Industrial 6-Port Managed PoE Switch
INTRODUCTION
The RocketLinx 7506 is designed for industrial PoE applicaons where the
power source is not conveniently located, such as IP surveillance or wireless
access points.
See the Comtrol website for complete product specicaons.
INSTALLATION OVERVIEW
You can use the following overview to install the ES7506. If you need more
detailed installaon and conguraon informaon, you can refer to the
RocketLinx ES7506 User Guide
, which is available on the RocketLinx CD or
you can download the latest version.
Wiring the Power Inputs
The ES7506 provides redundant power, reverse polarity protecon, and
accepts a posive or negave power source but PW1 and PW2 must apply
to the same mode. The power supplies should be UL Listed with a minimum
output rang of 24-55VDC and at 2.5A.
Electrical Specicaons Values
Power Input
Voltage
PWR1/PWR2
IEEE 802.3af Standard, Manual 48 (48-57VDC)
IEEE 802.3af Ultra 55 (55-57VDC)
Forced 15.4W 48 (48-57VDC)
Forced 30W 55 (55-57VDC)
PoE Output Voltage IEEE 802.3af Standard, Manual 44-57V
IEEE 802.3af Ultra 50-57V
Forced 44-57V
Maximum PoE
Power/Port
IEEE 802.3af Standard, Manual 15.4W
IEEE 802.3af Ultra, Forced 30W
Total Power Budget Maximum Up to 100 W
Power Consumpon Maximum 8W without PD
load
1
1. Insert the posive and negave wires into PW+ and PW- contacts (PW1
and PW2). You can connect a single power supply or two power supplies
depending on your requirements.
2. If both power inputs are connected, the ES7506 is powered from the
highest connected voltage. The unit can be congured to signal an alarm
for loss of power in either PW1 or PW2.
3. Tighten the wire-clamp screws to prevent the wires from being
loosened.
Power should be disconnected
from the power supply before
connecng it to the switch.
Otherwise, your screwdriver
blade can inadvertently
short your terminal
connecons to the grounded
enclosure.
Wiring the Alarm Relay Output
The alarm relay output or digital
output (DO) contacts are on the
terminal block connector on the side of the ES7506. The power supply
should be UL Listed with a minimum output rang of 2.5A at 24-55VDC.
The relay contacts are energized (open) for normal operaon and close
under faulty condions. Faulty condions can include power failure, Ethernet
port link break, or other predened events congurable in the ES7506 user
interface. To acvate the alarm relay output funcon, refer to the
RocketLinx ES7506 User Guide
.
2
Power Supply AC Power Input
24-55VDC/2.5A
(UL Listed)
V-
V+
Wiring Posive Power Supplies
Power Supply AC Power Input
12-24AWG
12-24AWG V-
V+
DC Power Input
24-55VDC
24-55VDC
DC Power Output 24-55VDC/2.5A
(UL Listed)
Alm PWR2PWR1
+-+ -
Grounding the E7506
Wire the earth ground to ensure the system is not damaged by noise or any
electrical shock, we recommend that you make a direct connecon between
the ES7506 and earth ground.
Using a screw driver, loosen the earth ground screw on the side of the
ES7506 and then ghten the screw aer the earth ground wire is connected.
Mounng the ES7506
Use the appropriate procedure to mount the ES7506 on the wall or a DIN rail.
Connecng RJ45 Ports
Connect one end of an Ethernet cable into the Ethernet port of the ES7506
and the other end to the aached networking device. The Ethernet ports
support 10/100Mbps half/full-duplex. All ports auto-detect the signal from
connected devices to negoate the link speed and duplex mode. Auto
MDI/MDIX allows users to connect another switch, hub, or workstaon
without changing straight through or crossover cable.
Link/Act LEDs are lit to indicate trac and link status, see the LEDs subsecon
for more informaon.
3
Attaching the ES7506 to the Wall
Use the hook holes located at the corners of
the wall-mount plate to mount the ES7506.
DIN Rail Mounting
Two DIN rail clips and four screws were shipped
with the ES7506. Use the screws to attach the
DIN rail clip to the wall-mount plate.
4
Always make sure that the cables between the
switches and aached devices (for example,
switch, hub, or workstaon) are less than 100
meters (328 feet).
• 10BASE-T: Category 3, 4, or 5 cable
• 100BASE-TX: Category 5 cable
• IEEE 802.3af: Category 5 cable
PROGRAMMING THE IP
ADDRESS
Congure the IP address using one of the
following methods:
• PortVision DX (available on the RocketLinx CD shipped with the product)
• Web browser
• Telnet
• Command Line Interface (CLI) using the RS-232 console cable
The easiest way to congure a stac IP address for your network in the
ES7506 is to use a Windows host and PortVision DX (see below). For
informaon about using other conguraon methods, refer to the
RocketLinx ES7506 User Guide.
Note: Oponally, you can use NetVision if you are accustomed to using NetVision.
PortVision DX is replacing NetVision. NetVision is not documented in the
RocketLinx ES7506 User Guide.
The following procedure uses PortVision DX to program network sengs.
1. Install PortVision DX on a host system with a Windows operang
system. If you need assistance installing PortVision DX, see the
RocketLinx ES7506 User Guide.
2. Start PortVision DX. PortVision DX can be started from Start --> All
Programs --> Comtrol --> PortVision DX.
3. Click the Scan buon.
4. Select the Comtrol product families that you want to locate and click the
Scan buon.
(cont. on page 5)
10/100BASE-TX PoE
(Alternave B)
1 RX+
2RX-
3 TX+
4,5 Vport+
6TX-
7,8 Vport-
(cont. from page 4)
5. Right-click the ES7506 in the
Device List
pane (lower) that you want to
congure and click Properes.
6. Enter a user-friendly Device Name.
7. Oponally, enter the ES7506 serial number, which displays a friendly
device name in the
Device List
pane on the main page.
8. Select DHCP IP or Stac IP for the IP Mode.
• If you select DHCP IP, go to Step 9.
• If you select Stac IP, enter an IP address, Subnet Mask, and
Default Gateway value for your network.
9. Oponally, select the appropriate Network Topology, which is an
informaonal eld.
10. Click the Apply Changes buon.
11. Click Close to return to the main screen.
You are now ready to congure the ES7506 features.
LED INDICATORS
You can also view the LEDs for the ES7506 through the web interface using
the
Device Front Panel
page.
LEDs LED On LED Blinking LED O
Alm
(Alarm)
Alarm acvated
or port link down
Not applicable Alarm not acvated
PW1/
PW2
Green: Power Not applicable No power
R.M.
(Ring
Master)
Green: Working
as a Ring Master
Amber: Ring
failed
Ring funcon disabled
PoE 1-4 Amber: PoE
powering
Blinking: PoE
Detect
Blinking fast: PoE
powering failure
PoE disabled: power
output over current, a
cable short, or PoE is
disabled for that port
LNK/ACT
1-6
Port link up Acve
connecon
Port link down or port
not connected
5
FEATURE CONFIGURATION
The ES7506 provides both in-band and out-band conguraon methods:
Out-band management means that you congure the ES7506 using the
RS-232 console cable and the Command Line Interface (CLI) to access the
ES7506 without aaching an admin PC to the network. You can also use
out-band management, if you lost the network connecon to the ES7506.
In-band management means that you connect remotely using the ES7506
IP address through the network. You can remotely connect with the ES7506
Java applet web interface or a Telnet console and the CLI.
The following procedure uses a web browser to congure ES7506 features.
Refer to the
RocketLinx ES7506 User Guide
for other conguraon methods.
1. If necessary, install the latest version of the Java Runme Environment,
which is required to run the web management interface.
2. Open a web browser and enter the IP address of the ES7506.
3. Click Run when Java prompts you to run the applet.
4. Enter admin for both the user name and the password when prompted.
5. Use the web interface to congure your device as needed for your
network.
You can use the help system or the
RocketLinx ES7506 User Guide
for
informaon about conguring ES7506 features.
6
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method Web Address or Phone Number
Support hp://www.comtrol.com/support
Downloads p://p.comtrol.com/html/ES7506_main.htm
Website hp://www.comtrol.com
Phone +1 763.957.6000
7
Otros manuales para ROCKET LINX ES7506
1
Tabla de contenidos
Otros manuales de Cambiar de Comtrol
Comtrol
Comtrol RocketLinx MP1204-XT Manual de usuario
Comtrol
Comtrol RocketPort Serial Hub Si Manual del operador
Comtrol
Comtrol ROCKETLINX ES7206-XT Manual de usuario
Comtrol
Comtrol RocketLinx ES8108 Manual de usuario
Comtrol
Comtrol ROCKET LINX ES7506 Manual de usuario
Comtrol
Comtrol RocketLinx ES7506 Manual de usuario
Comtrol
Comtrol ROCKET LINX MP1204-XT Manual de usuario
Comtrol
Comtrol ROCKETLINX ES8509-XT Manual de usuario
Comtrol
Comtrol ROCKETLINX ES7510-XT Manual de usuario
Comtrol
Comtrol RocketLinx ES8108 Manual de usuario
Comtrol
Comtrol ROCKETLINX ES8510 Manual de usuario
Comtrol
Comtrol ROCKETLINX ES7105 Manual de usuario
Comtrol
Comtrol ROCKETLINX ACS7106 Manual de usuario
Comtrol
Comtrol RocketLinx ES8105 Manual de usuario
Comtrol
Comtrol Satyrn U041-RE-M12 Manual de usuario
Comtrol
Comtrol RocketLinx ES8108 Manual de usuario
Comtrol
Comtrol ROCKETLINX ES7110-VB Manual de usuario
Comtrol
Comtrol ROCKETLINX ES8508 Manual de usuario
Comtrol
Comtrol Rocketlinx ES8108-GigE Manual de usuario
Comtrol
Comtrol RocketPort RPUSBSH Manual del operador
