CommScope BSAMNT-3 Manual de usuario
Part Lists
M8 screw
two hole plate
7
• Bracket edges parallel to each other.
(fully collapsed position)
Pre-assembly of Downtilt Brackets by Kit Vendor
(Not applicable for BSAMNT-F)
5
15
6
16
3
4
17
M10 screw
SCISSOR GASKET
ITEM NO.
DESCRIPTION
BSAMNT-3
QUANTITY
BSAMNT-M/-MH
QUANTITY
BSAMNT-F
QUANTITY
1
PIPECLAMP BRACKET, NO FLANGE
424
2
BRACKET, PIPE CLAMP INTERFACE
212
3
NOTCHED BRACKET
1 1
-
4
BRACKET
1 1
-
5
SCR,HCS,HEX,M8X25,10mm UNT,SST,PASS
2 2
-
6
WSHR,BELLE,M8,16-8.2-1.5,SST,PASS
2 2
-
7
PLATE, TWO HOLES
2 2
-
8
NUT,HEX,M10,STL,GALV
12 8 8
9
WSHR,LK,SPLT,M10,STL,GALV
644
10
SCR,HCS,HEX,M10X40,STL,GALV
644
11
NUT,HEX,M12,STL,GALV
12 6 12
12
WSHR,FLT,M12,13X24X2.5,STL,GALV
424
13
WSHR,LK,SPLT,M12,STL,GALV
424
14
CARRIAGE BOLT,WITH HEAT SHRINK
424
15
SCR,HCS,HEX,M10X25,10mm UNT,SST,PASS
2 2
-
16
WSHR,BELLE,M10,20-10.2-1.6,SST,PASS
2 2
-
17 SCISSOR GASKET 2 2
-
18
WSHR,FLAT,M16,17.5x30x2.5,SST
424
19
ISOLATOR
424
Mounting Kits For Wide Panel Antennas
BSAMNT-3, BSAMNT-M & BSAMNT-MH & BSAMNT-F: Mounting systems for
cylindrical pipe
installations
(60-115 mm pipe diameter) for heavy duty applications
This document explains how to install an antenna using a BSAMNT mount kit. Antennas with two mount points
will use BSAMNT-3 or BSAMNT-F. Antennas with three mount points will also include the BSAMNT-M or
BSAMNT-MH. The antenna mechanical tilt can not be adjusted if BSAMNT-F is used.
639840 Revision J, February 2020
Page 1 of 4
www.commscope.com
© 2020 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 J (02/20)
Pre-assembly of Pipe Bracket by Field Installer
(BSAMNT-3/-F QTY 2 EA)
(BSAMNT-M/-MH QTY 1 EA)
CRITICAL: For initial installation
to pipe, downtilt brackets must
be configured in pre-assembly
position (fully collapsed).
M10 screw
M10 screw
Top / Middle Mount Installations
BSAMNT-3/-M/-MH
1
211
14
8910
11
13
12
11098
M10 screw
WARNING
: LOOSENING OR REMOVING BOLTS
THAT ATTACH MOUNTING PLATE TO ANTENNA
WILL VOID WARRANTY AND MAY RESULT IN
PRODUCT DAMAGE OR PERSONAL INJURY.
18
1098
11
13
12
BSAMNT-F
19
19
A
B
DETAIL A
DETAIL B
MAXIMUM TORQUE
M12
58N.m (43ft.lbs)
MAXIMUM TORQUE
M8
25N.m (18ft.lbs)
M10
40N.m (30ft.lbs)
M12
58N.m (43ft.lbs)
639840
Page 2 of 4
www.commscope.com
© 2020 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 J (02/20)
8
1
11
13
12
Bottom Mount Installation
M10 screw
M10 pivot screw
center location
(loosen only)
M10 pivot screw
(loosen only)
M8 adjuster screw
perimeter location
(remove to adjust tilt)
M10 pivot screw
(loosen only)
M10 pivot screw
(loosen only)
M10 pivot screw
(loosen only)
DETAIL D
•
Loosen pivot screws . (do
not remove)
• Remove adjuster screws.
• Adjust antenna angle.
(use inclinometer)
• Reinstall adjuster screws.
• Retighten all screws.
Adjusting Antenna Tilt - 2 POINT MOUNT
(Not applicable for BSAMNT-F)
use inclinometer to
adjust antenna angle
9 10
WARNING
: LOOSENING OR REMOVING BOLTS
THAT ATTACH MOUNTING PLATE TO ANTENNA
WILL VOID WARRANTY AND MAY RESULT IN
PRODUCT DAMAGE OR PERSONAL INJURY.
D
19
C
DETAIL C
MAXIMUM TORQUE
M10
40N.m (30ft.lbs)
M12
58N.m (43ft.lbs)
MAXIMUM TORQUE
M8
25N.m (18ft.lbs)
M10
40N.m (30ft.lbs)
M12
58N.m (43ft.lbs)
639840
Page 3 of 4
www.commscope.com
© 2020 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 J (02/20)
SAFETY NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. CommScope
installation instructions are written for such installation
personnel. Antenna systems should be inspected once a
year by qualified personnel to verify proper installation,
maintenance, and condition of equipment.
CommScope disclaims any liability or responsibility for the
results of improper or unsafe installation practices.
It is recommended that transmit power be turned off
when the field installation is performed. Follow all
applicable safety precautions as shown on this page.
Do not install on a wet or windy
day or when lightning or thunder
is in the area. Do not use metal
ladder.
Do not install near power lines.
Power lines, telephone lines,
and guy wires look the same.
Assume any wire or line can
electrocute you.
Wear shoes with rubber soles and
heels. Wear protective clothing
including a long-sleeved shirt and
rubber gloves.
use inclinometer to
adjust antenna angle
•
Loosen pivot screws . (do
not remove)
• Remove adjuster screws.
• Adjust antenna angle.
(use inclinometer)
• Reinstall adjuster screws.
Middle Bracket First
• Retighten all screws.
Adjusting Antenna Tilt - 3 POINT MOUNT
(Not applicable for BSAMNT-F)
Remote Electrical
Tilt Connection
The AISG connector fitted to the antenna is designed to accept
any AISG compliant cable assembly, commscope recommends
hand tightening AISG mating connector only. Applied torque to
the connector shall not exceed 1.5N*m.
RF Cable Connection
The female RF connectors fitted to the antenna are designed
to fit jumper cables with standard related male RF connector.
Tighten the RF connector coupling according to torque
specification in antenna label, if the RF connectors are
tightened beyond the recommend torque, the RF connection
to the antenna may be damaged.
M10 pivot screw
(loosen only)
M10 pivot screw
(loosen only)
E
M10 pivot screw
(loosen only)
M10 pivot screw
center location
(loosen only)
M10 pivot screw
(loosen only)
M8 adjuster screw
perimeter location
(remove to adjust tilt)
DETAIL E
MAXIMUM TORQUE
M8
25N.m (18ft.lbs)
M10
40N.m (30ft.lbs)
M12
58N.m (43ft.lbs)
639840
Page 4 of 4
www.commscope.com
© 2020 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 J (02/20)
Este manual sirve para los siguientes modelos
3
Otros manuales de Rack y soporte de CommScope
CommScope
CommScope RK4P45-29A Manual de usuario
CommScope
CommScope F-118-GL-E Manual de usuario
CommScope
CommScope NETpodium 1-1671578-1 Manual de usuario
CommScope
CommScope BSAMNT Series Manual de usuario
CommScope
CommScope FIST-GR2-SMS-01 Manual de usuario
CommScope
CommScope NETpodium 1-1671405-1 Manual de usuario
CommScope
CommScope OTE-M Manual de usuario
CommScope
CommScope CMC-21 Manual de usuario
CommScope
CommScope ODF-FF19CM-40RU Manual de usuario
CommScope
CommScope DB5091-3 Manual de usuario
CommScope
CommScope NETpodium 1-1671579-1 Manual de usuario
CommScope
CommScope BSAMNT-SBS-1-2 Manual de usuario
CommScope
CommScope BSAMNT-SBS-2-3 Manual de usuario
CommScope
CommScope IST-GPS2 Manual de usuario
CommScope
CommScope 639849 Manual de usuario
CommScope
CommScope FL1000 Manual de usuario
CommScope
CommScope 2RU FMT Manual de usuario
CommScope
CommScope SYSTIMAX iPatch 600A Manual de usuario
CommScope
CommScope MC-MNT-3XV-SIDE Manual de usuario
