CommScope BUDI-S Manual de usuario

BUDI-S

INSTALLATION INSTRUCTION

Building distributor

• Box

• Base tray

• Base tower

• Termination units

• Inserts for SMOUV and ANT

Accessories

Introduction

Suitable for FTTH applications where easily pre-connectorized splitters

modules can be build in. The box is designed In such a way that it is

suitable for both spliced and connectorized solutions of the riser cable.

Kit content

• Tray kit

Seals

Wrap around cable seals

Sealblock 4 x 10 mm

Cable diameter (mm) Foam (± 5 mm)

3 95

4 90

5 80

6 75

7 70

8 60

9 50

10 40

Sealblock 4 x 15 mm

Cable diameter (mm) Foam (± 5 mm)

9 125

10 115

11 105

12 95

13 85

14 70

15 60

Sealblock 2 x 20 mm

Cable diameter (mm) Foam (± 5 mm)

14 155

15 140

16 125

17 110

18 95

19 85

20 75

Sealblock 24 x 8 mm

Cable range 1.8 – 7 mm

Sealblock rubber 1 x 18

To use in ports S4-S5 only

Cable range 3 – 8 mm

Standard seals

PG 16

PG 21

PG 29

PG 29 (PTS 24)

TC-906-S-IP

Rev A, Mar 2017

www.commscope.com

1.3 Different wrap-around ports are available (including brackets).

Use two guiding pins to open the ports and to secure the bottom part to

the box.

1.4 Install the cable bracket depending the cable seal.

1.1 Make a cut on both sides of the port to open the port.

1 Preparation of the box

1.2 Use a plier to break-out the port, starting from front to back.

Remove all the burrs.

S1 S2 S3

2.1 Mark the loose tube at the position of the tray.

2.2 1: Storage area (dark ﬁbers)

2: Splicing to splitter modules

3: Point to point applications

1.5 Use a hacksaw to reach the onion rings, which can be opened

with a plier to open the in-line ports (S4/S5).

1.6 Install the wrap-around rubber seal into the port.

2 Base tray

2.3 Route the ﬁbers to the different areas (1-2-3).

S4 S5

2.4 Store the ﬁbers which will be used later.

2.5 Store the ﬁbers which will be spliced day 1 to the splitter

modules.

2.6 Store the ﬁbers which will be spliced day 1 for the point-to-

point applications.

3 Drop cables (point-to-point applications)

3.1 Remove the outer jacket over a distance of 1.2 m.

3.2 Wrap one layer of foam (20 mm) on the securing position if

needed. Terminate the aramid strength member by securing the cable/

pigtail onto thebracket with tie-wrap. Depending the amount of aramid

strength member, it needs to be wrapped twice around the bracket.

3.3 Install the terminated drop cable in the numbered ports on the

base tray.

3.4 Splice the ﬁbers from the drop cable to the ﬁbers from the

looped cable. In case of SMOUV, use the insert.

3.5 Install the cover onto the tray.

Slide

Click

4.1 Install the patch tray onto the tower.

4.2 Insert the adaptor into the designated positions.

4 Patching tray

4.3 Install the cable into the port and secure with hook and loop

fastener tape onto the bracket and seal with foam (see length page 1).

Mini –PICO (no connectors)

4.4 Close the port.

4.5 Install the foam at the position on the patch tray and secure

with 2 tie-wraps as shown on the picture.

4.6 Install the splice holders onto the patch tray.

4.7 Splice the MINI PICO ﬁbers to the pigtails and store the

overlength in the splice area. Check the orientation of both ﬁbers to

avoid crossings.

Foam

Hook and loop

fastener

Hook and loop

fastener

4.8 Install the cover onto the tray.

Mini PICO (pre-connectorized)

4.10 Connect the mini PICO cable with the designated adaptors

and store the overlength in the splice area.

4.9 In case of pre-connectorized MINI PICO cable, ﬁbers are also

routed behind the tower and secured with foam and tie-wraps onto the

tray.

4.11 Install the cover onto the tray.

Click

Slide

Click

4.13 2 parking places for pigtails from splitter which are not used

day 1 can be installed.

4.12 Secure the patch trays with the rubber ﬂex part, as shown.

5.3 Install the splitter into the holder.

5.5 Install the incoming pigtail and route the ﬁber to the splicing to

“splicing to splitter modules” for splicing. Remove the outer jacket over a

distance of 1.2 m. Secure with foam and tie-wrap.

5.4 Route the pigtails to the designated adapters on the patch tray.

Bundle the pigtails with hook and loop fastener when needed.

5.2 Install the bend control and splitter holder into the box.

5 Splitters

OCM6 in-line

5.1 Install the adapter in the splitter holder.

OCM6 butt

5.7 Route the incoming pigtails of the splitter (marked with red

ﬂag) to the base tray and remove the outer jacket from the mark over a

distance of 1.2 m. Secure with foam and tie-wrap onto the base tray.

5.6 Install the splitter into the holder and route the pigtails via the

bend control.

5.8 Install the splice holders onto the patch tray.

5.9 Splice the MINI PICO ﬁbers to the pigtails and store the

overlength in the splice area. Check the orientation of both ﬁbers to

avoid crossings.

Slide Click

6 Closing the box

6.1 Close the box.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cables y conectores de CommScope

CommScope

CommScope OFDC-A4 SPLICE/PATCH Manual de usuario

CommScope

CommScope 760230938 Manual de usuario

CommScope

CommScope FOSC 450 A Manual de usuario

CommScope

CommScope NOVUX SEC 100 Manual de usuario

CommScope

CommScope AMP NETCONNECT SL Series Manual de usuario

CommScope

CommScope AMP NETCONNECT 1933352 Series Manual de usuario

CommScope

CommScope QWIK MPO Series Manual de usuario

CommScope

CommScope FOSC-350C Manual de usuario

CommScope

CommScope SYSTIMAX 360 760150144 Manual de usuario

CommScope

CommScope FDH1204-24SE2 Manual de usuario

CommScope

CommScope FIST-RSKG-1 Manual de usuario

CommScope

CommScope SYSTIMAX VisiPatch CPC5562 Manual de usuario

CommScope

CommScope FD21206-48SRC Series Hoja de instrucciones

CommScope

CommScope OSP-CLPFEC-LG Manual de usuario

CommScope

CommScope HELIAX FiberFeed HFA208 Series Hoja de instrucciones

CommScope

CommScope HELIAX FiberFeed HFE810 Series Hoja de instrucciones

CommScope

CommScope FOSC-450D Manual de usuario

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-G2-1U-LC-FX Manual de usuario

CommScope

CommScope LightCrimp Plus SC Simplex Manual de usuario

CommScope

CommScope M2400 Series Manual de usuario

CommScope

CommScope SYSTIMAX 360 iPatch PATCHMAX Manual de usuario

CommScope

CommScope LC Manual de usuario

CommScope

CommScope FIST-RSKG-16 Manual de usuario

CommScope

CommScope FACT Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario