ComAp InteliLite NT MRS19 Manual de usuario
InteliLite NT MRS19 Quick Start Guide
This guide was created to provide instruction on some of the most common
tasks involved when working with the IL-NT-MRS19. This Guide includes
information on;
1. Where to get the Correct Software and Manuals?
2. How to Connect and Save the Archive?
3. Procedure for Replacing a Controller
4. Upgrading Controller Firmware
5. FAQ’s
a. What does FLS stand for?
b. What does Wrn RA15 Fail mean?
c. What does Wrn Maintenance mean?
A short video has been created to briefly introduce you to configuring your
controller using LiteEdit. This contains information on how to configure
inputs/outputs, sensors, extension modules, and your ECU.
https://youtu.be/yIKOnHDkBps
IL-NT-MRS19 Software and Manuals
Step 1: Go to https://www.comap-control.com/products/detail/intelilite-nt-mrs-19
▪You will need to log-in/create your ComAp Members Club account prior to downloading any
software or manuals from our website. This can be done in the upper right corner of the web
page.
Step 2: Scroll down to the downloads section> Expand software> Download the
InteliLite NT 2.2.0 Installation Suite.
▪This will provide you with the LiteEdit software needed to program your controller.
Step 3: Expand manuals and download the InteliLite NT MRS 2.2 Reference Guide.
▪This is the main manual for the controller.
If Interfacing with an ECU: Expand manuals and download the Electronic Engines Support
Guide. This will help you properly establish communication with the ECU.
If setting up Modbus, Remote Connection, Internet Connection, or any
other communication protocol: Expand manuals and download the IL-NT Communication
Guide. This manual with go in-depth, explaining how to properly establish various communication
protocols and interfaces.
Connecting to IL-NT-MRS19 and Saving the
Archive File
Step 1: You will need LiteEdit installed on your computer, along with a 9-pin serial null
modem cable and USB to serial adapter to physically connect your computer to the
controller.
▪If using your USB to serial adapter for the first time- Confirm the driver is correctly installed by
double-clicking on the adapter shown in the picture below.
Step 2: Connect your computer to the controller> Power on the controller> Open
LiteEdit.
Step 3: Open a Direct Connection
Step 4: Select the COM port of your computer that the adapter is plugged into.
▪This can be confirmed by viewing your ports in device manager (shown below). Double-clicking
on the adapter will show the device driver status.
Step 5: Select the correct controller address and confirm COM1 mode is set to Direct.
▪This can be found by pressing page> Comms Settings on the front screen of the controller. *If you
have a controller with old firmware, this will be found under basic settings.
▪If COM1 mode needs to be changed, press enter and use the arrows to select direct. If there is an *
before the setpoint like shown below, the password must be entered first. This can be done by
pressing page and selecting password.
Step 6: Confirm you are connected!
▪This is done by seeing a green status bar and Dde server: Running status at the bottom
of LiteEdit
Step 7: Select connection and save as.
▪Save in an easy to find location on your computer.
If you fail to connect;
▪Remove the back cover and confirm the RS232 plug-in module is correctly installed and no pins
are damaged on the circuit board. *If viewing the controller from rear, module must be on right
side!
▪Confirm your 9-pin serial cable is a Null Modem, they are not all the same! Null modem means
pins 2 and 3 are swapped and not straight through. You can verify this by testing continuity if
need be.
▪Confirm all connects are solid and cables in good condition.
Programming your Replacement IL-NT
Controller
*These instructions are to be used when you are replacing a controller and want to
“pull” program from old controller and load it into the new one. These can also be
used if you want to make a “copy” of another controller.
Step 1: Connect to old controller and save the archive in an easy to find location.
Step 2: Right-click on that saved archive> make a copy and paste it in same location. (As seen below)
Step 3: Connect to the new controller.
Step 4: Select controller>values>IL info.
▪Take note of the new controller FW version. You will need this information. (Below is an
example of controller with FW 2.2)
Step 5: Select controller>programming and cloning>archive/configuration upgrade
▪A new window will pop up (shown below)
Step 6: Select “Add” and choose the copy of the archive you saved from previous controller.
Step 7: Expand the target archive and select the same firmware version as your new controller.
Step 8: Make sure the output directory is in the same location as the copy archive. (shown below is
steps 6-8 completed)
Step 9: Continue to press next and when asked if you want to overwrite the existing copy archive,
select “Yes to All”. (shown below)
Step 10: Right-click on the copy of the archive you just converted to the new firmware version and
rename the file so you know it has been updated (shown below).
▪You can also open this file offline to confirm the archive did indeed upgrade to the newer FW
version.
Step 11: Connect to the new controller
Step 12: Press the “select configuration” icon from the top task bar (shown below) and select the
archive you have just updated and renamed.
Step 13: You will be asked if you want to save the actual archive- this is a default archive and saving
it is not necessary, so select “no”.
Step 14: The configuration of the old controller will pop up, select “Write to controller” (shown
below)
▪You will be asked if you want to overwrite setpoints by values from the selected archive, press
“Yes”.
Your controller is now programmed!
▪Please take the time to verify all setpoints and configuration has transferred properly. There
can sometimes be errors when a large firmware change is taking place. There can also be errors
when the updated firmware version has new setpoints/features that were previously not there.
Tabla de contenidos
Otros manuales de Controladores de ComAp
ComAp
ComAp InteliLite 4 MRS16 Manual
ComAp
ComAp IG-NT GC Manual de usuario
ComAp
ComAp InteliNano NT MRS Manual de usuario
ComAp
ComAp InteliGen NTC Manual de uso y cuidado
ComAp
ComAp InteliATS NT STD Manual de usuario
ComAp
ComAp intelilite nt amf20 Manual de usuario
ComAp
ComAp InteliDrive FLX LITE Manual de usuario
ComAp
ComAp InteliSys NT Manual de programación
ComAp
ComAp InteliLite4 AMF20 Manual
ComAp
ComAp InteliDrive Lite Manual de usuario
ComAp
ComAp InteliDrive DCU Industrial Manual de usuario
ComAp
ComAp InteliSys NTC BaseBox Manual de uso y cuidado
ComAp
ComAp InteliLite NT MRS Manual de usuario
ComAp
ComAp InteliLite NT AMF 25 Manual
ComAp
ComAp InteliDrive DCU Marine Manual de usuario
ComAp
ComAp InteliNano MRS 3 Manual
ComAp
ComAp IGS-NT Series Manual de usuario
ComAp
ComAp InteliLite MRS16 Manual de usuario
ComAp
ComAp InteliLite 9 Manual de usuario
ComAp
ComAp IM-NT-BTB Manual
