Cognex In-Sight SnAPP Series Manual de usuario
In-Sight®SnAPP Series
Quick Reference Guide
2023 September 01
Revision: 23.1.0.6
Precautions
To reduce the risk of injury or equipment damage, observe the following
precautions when you install the Cognex product:
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lDo not install Cognex products where they are exposed to environmental
hazards such as excessive heat, dust, moisture, humidity, impact,
vibration, corrosive substances, flammable substances, or static electricity.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lDo not expose the image sensor to laser light. Image sensors can be
damaged by direct, or reflected, laser light. If your application requires
laser light that might strike the image sensor, use a lens filter at the
corresponding laser wavelength. For suggestions, contact your local
integrator or application engineer.
lThis product does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lInclude service loops with cable connections.
2
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
3
Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or
electrical shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4
Accessories
You can purchase the following components separately. For a list of options and
accessories, contact your local Cognex sales representative.
Mounting Brackets
Accessory Product Number Illustration
Pivot mounting bracket DM100-PIVOTM-01
Tilted angle pivot bracket DMBK-DMPIVOT-00
Cables
Note: Cables are sold separately.
Accessory Product Number Illustration
Ethernet Cable, X-coded M12-8 to
RJ-45
CCB-84901-2001-xx (straight, xx specifies length:
2m, 5m, 10m, 15m, 30m)
Ethernet Cable, X-coded M12-8 to
RJ-45
CCB-84901-2002-xx (right-angled, xx specifies
length: 2m, 5m, 10m)
5
Accessory Product Number Illustration
Ethernet Cable, Robotic X-Coded
M12-8 to RJ-45
CCB-84901-2RBT-xx (straight, xx specifies length:
2m, 5m, 10m)
X-Coded to A-Coded Ethernet cable
adapter, 0.5 m
CCB-M12X8MS-XCAC
Power and I/O Breakout Cable, M12-
12 to Flying Lead
CCB-PWRIO- xx (straight, xx specifies length: 5m,
10m, 15m)
Power and I/O Breakout Cable, M12-
12 to Flying Lead
CCB-PWRIO-xxR (right-angled, xx specifies length:
5m, 10m, 15m)
I/O Module Cable M12-12 to DB15 CCB-PWRIO-MOD-xx (xx specifies length: 2m, 5m)
RS-232 Connection Cable CCB-M12xDB9Y-05
I/O Extension Cable CKR-200-CBL-EXT
6
Setting Up Your In-Sight Vision Sensor
Read this section to learn how the vision sensor connects to its standard
components and accessories.
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact
your Cognex Authorized Service Provider (ASP) or Cognex
Technical Support.
CAUTION:All cable connectors are keyed to fit the connectors on the vision
sensor. Do not force the connections or damage may occur.
7
Vision Sensor Layout
The image and table below shows the elements of the vision sensor.
Number Description
1 Power I/O Breakout cable connector
2 USB-C slot (with plastic cover)
3Ethernet connector
4Illumination LEDs
8
Number Description
5 LED aimer
6 Trigger button
Note: The Trigger Button is not supported.
7 Tune button
Note: The Tune Button is not supported.
8Indicator LEDs
9
Number Description
9Power LED indicator
10 Train status/Trigger status LED indicator
11 Good/bad inspection LED indicator
12 Communication LED indicator
13 Error LED indicator
10
Tabla de contenidos
Otros manuales de Lector de código de barras de Cognex
Cognex
Cognex DM260Q Manual de usuario
Cognex
Cognex DataMan 503 Manual de usuario
Cognex
Cognex DataMan 260 Series Manual de usuario
Cognex
Cognex DataMan 475 Manual de usuario
Cognex
Cognex DataMan 260 Manual de usuario
Cognex
Cognex DATAMAN 500 Manual de usuario
Cognex
Cognex DataMan 8700 Manual de usuario
Cognex
Cognex DataMan 50 Manual de usuario
Cognex
Cognex DataMan 8072 DL Manual de usuario
Cognex
Cognex DataMan 280 Series Manual de usuario
Cognex
Cognex DM 8072DL Manual de usuario
Cognex
Cognex DataMan 280 Series Manual de usuario
Cognex
Cognex DataMan 100 Manual de usuario
Cognex
Cognex DataMan 8000 Series Manual de usuario
Cognex
Cognex Advantage 182 Series Instrucciones de montaje
Cognex
Cognex DataMan Instrucciones de funcionamiento
Cognex
Cognex DataMan 280 Series Manual de usuario
Cognex
Cognex DataMan DM474 Manual de usuario
Cognex
Cognex DataMan 8600 Verifier Series Manual de usuario
Cognex
Cognex In-Sight 2800 Series Manual de usuario
