Coemar CF ZOOM AL Manual de usuario
CF ZOOM AL
1^ edizione, gennaio 1999
1st edition, january 1999
manuale
di istruzioni
instruction
manual
CF ZOOM AL
numero di serie/serial number
data di acquisto/date of purchase
fornitore/retailer
indirizzo/address
cap/città/suburb
provincia/capital city
stato/state
tel./fax/
Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro
CF ZOOM AL
: in
caso di richiesta di informazioni, pezzi di ricambio, servizi di riparazione o altro ci permetteranno di assistervi con
la massima rapidità e precisione.
Please note in the space provided above the relative service information of the model and the retailer from
whom you purchased your
CF ZOOM AL
: This information will assist us in providing spare parts, repairs or in
answering any technical enquiries with the utmost speed and accuracy.
ATTENZIONE: la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti istruzioni, per-
tanto è necessario conservarle.
WARNING: the security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.
514 mm
692 mm
750 mm
204 mm
306 mm
592 mm 546 mm
Index
1. Packaging
2.Transportation
3.Important safety information
4. Lamp: installation and replacement
5. Operating voltage and frequency
6. Mounting the unit
7. Mains connection
8. Signal connection
9.Powering up
10.DMX addressing
11.Display panel functions
12.DMX 512 channel functions
13.Aligning the lamp in the optical path
14 Moving the reset/home position by 90°
15.Replacing dichroic filters on the colour wheel
16.Automatic functions
17.Maintenance
18.Electronic alignment of motors
19.Spare parts
Authorised coemar service centres worldwide
Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in
componentry and in the technology used. We renew our invitation to you to complete the service information on the pre-
vious page, to expedite any request for service information or spares (in case of problems encountered either during, or subse-
quent to, installation). This information will assist in providing prompt and accurate advice from your coemar service centre.
1. Packaging Following the instructions and procedures outlined in this manual will ensure the
maximum efficiency of this product for years to come.
Open the packaging and ensure that no part of the equipment has suffered damage
in transit. In case of damage to the equipment, contact your carrier immediately by
telephone or fax, following this with formal notification in writing.
packing list
Ensure the packaging contains:
1 CF ZOOM AL
1 instruction manual
1 end stop –90°
2. Transportation The CF ZOOM AL should be transported in its original packaging or in a coemar
approved flight case.
In order to manufacture a suitable flight case, we recommend the follwing simple pro-
cedure be followed, which will stop the articulated movement of the CF ZOOM AL.
Below are illustrated the 2 diverse methods of padding which we recommend:
A) Padding around teh entire projector, including the base, with suitable padding
materials.
B) Fixing the base to a rigid support, with padding surrounding the articulated head.
Polietilene
espanso/
Foam
Pomoli di
bloccaggio/
Knobs
Polietilene
espanso/
Foam
3.Important Fire prevention:
safety information 1. CF ZOOM AL utilises a Philips Fabolux 500W 55v; the use of any alternative
lamp is not recommended and will null and void the fixture’s warranty.
2. Never locate the fixture on any flammable surface.
3. Minimum distance from flammable materials: 0,5 m.
4. Minimum distance from the closest illuminable surface: 2 m.
5. Replace any blown or damaged fuses only with those of identical values. Refer to
the schematic diagram if there is any doubt.
6. Connect the projector to mains power via a thermal magnetic circuit breaker.
Prevention of electric shock:
1. High voltage is present in the internals of the unit. Isolate the projector from
mains supply prior to performing any function which involves touching the inter-
nals of the unit, including lamp replacement.
2. For mains connection, adhere strictly to the guidelines outlined in section 7 of this
manual.
3. The level of technology inherent in the CF ZOOM AL requires the use of specia-
lised personnel for all service applications; refer all work to your authorised coe-
mar service centre.
4. A good earth connection is essential for proper functioning of the projector.
Never operate the unit without proper earth connection.
5. The fixture should never be located in an exposed position, or in areas of extreme
humidity. A steady supply of circulating air is essential.
Safety:
1. The projector should alwasy be installed with bolts, clamps, and other fixings
which are suitably rated to support te weight of the unit.
2. Always use a secondary safety chaing of a suitable rating to sustain the weight of
the unit in case of the failure of the primary fixing point.
3. The external surface of the unit, at various points, may exceed 150°C. Never hand-
le the unit until at least 10 minutes have elapsed since the lamp was turned off.
4. Always replace the lamp if any phusical damage is evident.
5. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient
temperature should not exceed 35°C.
6. A hot lamp may explode. always wait for at least 10 minutes to elapse after the
unit has been turned off prior to attempting to replace the lamp.
Always wear suitable hand protection when handling the lamp.
4. Lamp: Installation CF ZOOM AL utilises a Philips Fabolux 500W 55V lamp with a
and replacement GX 9,5 lampbase
The lamp is available from your authorised coemar sales agent:
coemar cod. 105071
wattage 500 W
luminous flux 11.880lm
colour temperature 3200° K
base GX 9,5
approximate life 200 hours
The fixture’s internal temperature can reach 250° C after 5 minutes, with a maximum
peak of 350° C; ensure that the lamp is cold prior to attempting removal. The fixture
should be allowed to stand and cool for 10 minutes prior to its removal.
The lamp is part of the tungsten halogen family of incandescent lamps and must be
handled with great care. The lamp operates at high temperature, and the slight risk
of explosion of the lamp exists if operated over its recommended life of 200 hours.
We recommend, therefore, that the lamp be replaced within the manufacturer’s spe-
cified lamp life.
mounting the lamp
1) Using a 3mm hex (Allen) key, remove the two hex bolts (A) which affix the lamp
assembly to the rear of the projector.
2) Remove the lamp assembly (B).
Attention
Turn off the power prior to opening up the unit.
3) Locate the lampholder (C)
4) The GX 9,5 lampholder is symmetrical in construction; the lamp used is manufac-
tured from quartz glass and should be handled with care; always adhere to the
instructions supplied in the lamp’s packaging. Never touch the glass directly, use
the tissue provided in the lamp’s packaging.
Insert the lamp (D) into the lampholder (C). DO NOT USE UNDUE FORCE. In case
of difficulty, re-read the instructions and repeat the procedure.
5) Replace the lamp assembly (B) into its original position and replace and tighten
the two screws (A) which were previously removed.
Attention: we recommend that the lamp be realigned in the optical train of the unit
to avoid overheating of the dichroic filters and other internal components of the
unit. refer to section 13 for instructions about this procedure.
5. Operating voltage and coemar factory presets (barring specific requests), a voltage of 230v and 240v
frequency selectable via the switch on the base of the CF ZOOM AL.
Remember to switch the selector (230 or 240V) to the position which best matches
the average voltage available at your particular venue. The following diagrams show
the transformer settings as set by coemar.
If your required operating voltage is 208V, you may select this internally within the
unit by moving the cables numbered 20 and 18 (currently connected in the 240V
position) or the cables numbered 19 and 17 (currently connected in the 230V posi-
tion), thereby no longer availing yourself of either the 230V or 240V option.
18
Bianco/White
Nero/black 55V
Rosso/red 240V
Blu/blue 208V
Giallo/yellow 230V
17
16
55V
115V
208V
230V
240V
Marrone/brown 115V
13
115V
208V
230V
240V
22
Bianco/White
Nero/black 230V
Rosso/red 115 V
Blu/blue 240V
Giallo/yellow 208 V
19 20
18
Bianco/White
Nero/black 55V
Rosso/red 240V
Blu/blue 208V
Giallo/yellow 230V
17
16
55V
115V
208V
230V
240V
Marrone/brown 115V
13
115V
208V
230V
240V
22
Bianco/White
Nero/black 230V
Rosso/red 115 V
Blu/blue 240V
Giallo/yellow 208 V
19
20
240V
230V
main setting
coemar: user:
115V
200V
208V
230V
240V
main setting
coemar: user:
115V
200V
208V
230V
240V
Having altered the settings as required, mark the corresponding position on the
sticker located near the on/off switch as shown in the figure below:
Incorrect voltage selection will detrimentally affect the operation of
the projector.Under no circumstance should you move the cables
numbered 22,16 and 13.
The operating voltage, as distinct from the input voltage, does not
need to be altered.
240V
main setting
coemar: user:
115V
200V
208V
230V
240V
6. Mounting the unit mounting
The CF ZOOM AL may be either floor or ceiling mounted.
The structure from which the unit is hung should be of sufficient rating to hold the
weight of the unit, as should any clamps used to hang the unit.
The structure should also be sufficiently rigid so as not to move or shake whilst the
CF ZOOM AL moves during its operation.
The mounting holes in the base of the unit allow it to be mounted at various angles
to the mounting truss and to trusses of various dimensions.
The following is a diagram outlining the base of the CF ZOOM AL.
Note that in order to take advantage of the full articulated movement of the projec-
tor, it should be installed with the label marked ” Lato frontale/ Front” facing towards
the main item to be illuminated; in this manner the “0” or “home” position of the CF
ZOOM AL will be in the most efficient position.
165mm
165mm
455mm
n°6 asole 72x12 mm r= 6 mm
Tabla de contenidos
Otros manuales de Equipo de iluminación de Coemar
Coemar
Coemar par lite LED IP Manual de usuario
Coemar
Coemar Reflection LEDko Manual de usuario
Coemar
Coemar Reflection LEDko Manual de usuario
Coemar
Coemar CF 1200 Hard Edge Manual de usuario
Coemar
Coemar Reflection LedkoP Manual de usuario
Coemar
Coemar ReLite Led Kit T / D Manual de usuario
Coemar
Coemar Reflection FullSpectrum Manual de usuario
Coemar
Coemar LEDko EXT Manual de usuario
Coemar
Coemar Panorama Cyc 1800 Architectural Manual de usuario
Coemar
Coemar LineaLED Flexible Manual de usuario
Coemar
Coemar SunLite LED Series Manual de usuario
Coemar
Coemar Infinity Spot S Manual de usuario
Coemar
Coemar Otello 6 HD + Manual de usuario
Coemar
Coemar Stage Lite Led sc Manual de usuario
Coemar
Coemar Infinity Wash M Manual de usuario
Coemar
Coemar pilota 1200 Manual de usuario
Coemar
Coemar MiniLEDko Series Manual de usuario
Coemar
Coemar Reflection LEDko T Studio Manual de usuario
Coemar
Coemar i spot S Manual de usuario
Coemar
Coemar LineaLed Stick Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
