Coemar CF 1200 Hard Edge Manual de usuario

CF 1200 Hard Edge

1st edition, april 1999

instruction

manual

CF 1200 Hard Edge

serial number

date of purchase

retailer

address

suburb

capital city

state

tel./fax/

Please note in the space provided above the relative service information of the model and the retailer from

whom you purchased your

CF 1200 Hard Edge

: This information will assist us in providing spare parts,

repairs or in answering any technical enquiries with the utmost speed and accuracy.

WARNING: the security of the fixture is granted only if these instructions are strictly followed; therefore it is

absolutely necessary to keep this manual.

643 mm

368 mm

750 mm

602 mm

180,5 mm

733 mm

440 mm

180,5 mm

Index

1. Packaging

2. Transporting

3. Important safety information

4. Lamp: installation and replacement

5. Operating voltage and frequency

6. Mounting the unit

7. Mains connection

8. Signal connection

9. Powering up

10. DMX addressing

11. Display panel functions

11.1 Powering up the CF 1200 Hard Edge with movement disenabled

12. DMX 512 signal functions

13. Lamp alignment

14. Opening up the projector housing

15. Interchanging gobos

16. Interchanging dichroic filters

17. Automatic internal functions

18. Maintenance

19. Electronic motor alignment

20. Spare parts

Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in

componentry and in the technology used. We renew our invitation to you to complete the service information on the previous

page, to expedite any request for service information or spares (in case of problems encountered either during, or subsequent

to, installation). This information will assist in providing prompt and accurate advice from your coemar service centre.

1. Packaging Following the instructions and procedures outlined in this manual will ensure the

maximum efficiency of this product for years to come.

Open the packaging and ensure that no part of the equipment has suffered damage

in transit. In case of damage to the equipment, contact your carrier immediately by

telephone or fax, following this with formal notification in writing.

packing list

Ensure the packaging contains:

1 CF 1200 Hard Edge

1 instruction manual

2. Transporting The CF 1200 Hard Edge should be transported in its original packaging or ain a

coemar approved flight case.

In order to manufacture a suitable flight case, we recommend the follwing simple

procedure be followed, which will stop the articulated movement of the CF 1200

Hard Edge during transportation.

Below are illustrated the 2 diverse methods of padding which we recommend:

A) Padding around teh entire projector, including the base, with suitable padding

materials.

B) Fixing the base to a rigid support, with padding surrounding the articulated

head.

Polietilene

espanso/

Foam

Pomoli di fissaggio/

Knobs

Pomoli di fissaggio/

Knobs

Polietilene

espanso/

Foam

3.Important Fire prevention:

safety information 1. CF 1200 Hard Edge utilises a Philips MSR 1200 SA lamp; use of any alternative

lamp is not recommended and will null and void the fixture’s warranty.

2. Never locate the fixture on any flammable surface.

3. Minimum distance from flammable materials: 0,5 m.

4. Minimum distance from the closest illuminable surface: 2 m.

5. Replace any blown or damaged fuses only with those of identical values. Refer to

the schematic diagram if there is any doubt.

6. Connect the projector to mains power via a thermal magnetic circuit breaker.

Prevention of electric shock:

1. High voltage is present in the internals of the unit. Isolate the projector from

mains supply prior to performing any function which involves touching the inter-

nals of the unit, including lamp replacement.

2. For mains connection, adhere strictly to the guidelines outlined in section 7 of this

manual.

3. The level of technology inherent in the CF 1200 Hard Edge requires the use of

specialised personnel for all service applications; refer all work to your authorised

coemar service centre.

4. A good earth connection is essential for proper functioning of the projector.

Never operate the unit without proper earth connection.

5. The fixture should never be located in an exposed position, or in areas of extreme

humidity. A steady supply of circulating air is essential.

Protection against ultraviolet radiation:

1. Never turn on the lamp if any of the lenses, filters, or the carbon fibre housing is

damaged; their respective functions will only operate efficiently if they are in per-

fect working order.

Never look directly into the lamp when it is operating.

Safety:

1. The projector should alwasy be installed with bolts, clamps, and other fixings

which are suitably rated to support te weight of the unit.

2. Always use a secondary safety chaing of a suitable rating to sustain the weight of

the unit in case of the failure of the primary fixing point.

3. The external surface of the unit, at various points, may exceed 150°C. Never hand-

le the unit until at least 10 minutes have elapsed since the lamp was turned off.

4. Always replace the lamp if any phusical damage is evident.

5. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient

temperature should not exceed 35°C.

6. A hot lamp may explode. always wait for at least 10 minutes to elapse after the

unit has been turned off prior to attempting to replace the lamp.

Always wear suitable hand protection when handling the lamp.

4. Lamp: Installation CF 1200 Hard Edge utilises a Philips MSR 1200 SA lamp of 1200W with

and replacement a GY 22 base.

The lamp is available from your authorised coemar sales agent:

coemar cod. 105090/1

wattage 1200 w

luminous flux 96.000 lm

colour temperature 6500° K

base GY 22

approximate life 500 hours

The fixture’s internal temperature can reach 250° C after 5 minutes, with a maximum

peak of 350° C; ensure that the lamp is cold prior to attempting removal. The fixture

should be allowed to stand and cool for 10 minutes prior to its removal.

MSR/SA lamps are part of the mercury vapour family of discharge lamps and must be

handled with great care. The lamp operates at hight pressure, and the slight risk of

explosion of the lamp exists if operated over its recommended life of 500 hours.

We recommend, therefore, that the lamp be replaced within the manufacturer’s spe-

cified lamp life.

mounting the lamp

1) Using a 3mm hex (Allen) key, remove the two hex bolts (A) which affix the lamp

assembly to the rear of the projector.

2) Remove the lamp assembly (B).

3) Locate the lampholder (C)

Attention

Turn off the power prior to opening up the unit.

4) Insert the lamp (D). The lamp used is manufactured from quartz glass and should

be handled with care; always adhere to the instructions supplied in the lamp’s

packaging. Never touch the glass directly, use the tissue provided in the lamp’s

packaging. The GY 22 lampbase is assymetrical in construction, with one lamp

pin socket larger than the other; make sure therefore that the correct pin is lined

up into its respective pin socket. DO NOT USE UNDUE FORCE. In case of diffi-

culty, re-read the instructions and repeat the procedure.

5) Replace the lamp assembly (B) into its original position and replace and tighten

the two screws (A) which were previously removed.

Attention: we recommend that the lamp be realigned in the optical train of the

unit to avoid overheating of the dichroic filters and other internal components of

the unit. refer to section 13 for instructions about this procedure.

5. Operating voltage and coemar factory presets (barring specific requests), a voltage of 230v and 240v

frequency selectable via the switch on the base of the CF 1200 Hard Edge.

Remember to switch the selector (230 or 240V) to the position which best matches

the average voltage available at your particular venue.

If your required operating voltage is 208V, you may select this internally within the

unit by moving the cable numbered 21 (currently connected in the 240V position)

or the cable numbered 22 (currently connected in the 230V position), thereby no

longer availing yourself of either the 230V or 240V option.

Incorrect voltage selection will detrimentally affect the operation of

the projector. Under no circumstance should you move the cable num-

bered 26.

CF 1200 Hard Edge is fitted with an electronic ballast which automatically stabili-

ses the output voltage to the lamp with any input voltages within the range of 180 to

260V; there is therefore no need for any electrical modifications required for dealing

with voltages within this range.

115V

208V

230V

240V

Bianco/White

Nero/black 230V

Rosso/red 115 V

Blu/blue 240V

Giallo/yellow 208 V

115V

208V

230V

240V

Bianco/White

Nero/black 230V

Rosso/red 115 V

Blu/blue 240V

Giallo/yellow 208 V

240V

power

main setting

coemar:

208V

230V

240V

user:

208V

230V

240V

220V

power

main setting

coemar:

208V

230V

240V

user:

208V

230V

240V

6. Mounting the unit mounting

The CF 1200 Hard Edge may be either floor or ceiling mounted.

The structure from which the unit is hung should be of sufficient rating to hold the

weight of the unit, as should any clamps used to hang the unit.

The structure should also be sufficiently rigid so as not to move or shake whilst the

CF 1200 Hard Edge moves during its operation.

The mounting holes in the base of the unit allow it to be mounted at various angles

to the mounting truss and to trusses of various dimensions.

Note that in order to take advantage of the full articulated movement of the projec-

tor, it should be installed with the label marked ” Lato frontale/ Front” facing towards

the main item to be illuminated; in this manner the “0” or “home” position of the CF

1200 Hard Edge will be in the most efficient position.

protection against liquids

The projector contains electric and electronic components that must not come into

contact with water, oil, or any other liquid.

movement

The projector has a movement of 370° in the base and 270° in the yoke; DO NOT

place any obstructions in the path of the projector’s movement.

safety chain

The use of a safety chain (cod. 069) - fixed to the CF 1200 Hard Edge and to the

primary suspension point, is highly recommended to protect against accidental failu-

re, however unlikely, of the primary suspension point.

If using an after-market safety chain not manufactured by coemar, ensure that it is

of sufficient rating to hold the weight of the fixture.

risk of fire

Each fixture produces heat and must be installed in a well-ventilated position. The

minimum recommended distance from flammable material is: 0.5m. Minimum

distance from the object being illuminated is: 2 m.

7. Mains connection cabling

The mains cable provided is thermally resistant, complying to the most recent

international standards. It meets or exceeds the VDE and IEC norms, IEC 331,

IEC 332 3C,CEI 20 35.

NB: In case of cable replacement, similar cable with comparable thermal resistant quali-

ties must be used exclusivelly (cable 3x1.5 ø external 10 mm, rated 300/500V, tested

to 2KV, operating temperature -40° +180°, coemar cod. CV5309).

mains connection

The CF 1200 Hard Edge can operate at voltages from 208V-230V-240V at 50 or

60Hz (operating voltage and frequency can be selected as described in section 5 of

this manual).

Prior to connecting the unit to your mains supply, ensure that the model in your pos-

session correctly matches the mains supply available to you.

For connection purposes, ensure your plug is of a suitable rating: 9.5 amps.

Locate the mains cable which exits the base of the unit and connect as shown

below:

massa

ground

neutro

neutral

fase

phase

marrone - brown

blu - blue

giallo/verde - yellow/green

marrone - brown

blu - blue

giallo/verde - yellow/green

marrone - brown

blu - blue

giallo/verde - yellow/green alimentazione

main

Otros manuales para CF 1200 Hard Edge

Tabla de contenidos

Otros manuales de Equipo de iluminación de Coemar

Coemar

Coemar FX PROJECTOR Manual de usuario

Coemar

Coemar Reflection LEDko Manual de usuario

Coemar

Coemar ReLite Led Kit VariWhite 250 Manual de usuario

Coemar

Coemar Panorama Cyc 1800 Architectural Manual de usuario

Coemar

Coemar Risalto Led + Manual de usuario

Coemar

Coemar LEDko EXT Manual de usuario

Coemar

Coemar LEDko DIM T Manual de usuario

Coemar

Coemar LineaLED Flexible Manual de usuario

Coemar

Coemar MiniLEDko Series Manual de usuario

Coemar

Coemar Reflection LEDko Manual de usuario

Coemar

Coemar LineaLed Stick Manual de usuario

Coemar

Coemar ProSpot 150 LX Manual de usuario

Coemar

Coemar pilota 1200 Manual de usuario

Coemar

Coemar i spot S Manual de usuario

Coemar

Coemar Reflection FullSpectrum Manual de usuario

Coemar

Coemar Par lite ACL Manual de usuario

Coemar

Coemar Mini ReLite Led Manual de usuario

Coemar

Coemar Par Lite Led Manual de usuario

Coemar

Coemar CF ZOOM AL Manual de usuario

Coemar

Coemar LEDko EXT Manual de usuario

Coemar

Coemar Reflection LEDko T Studio Manual de usuario

Coemar

Coemar Infinity Spot S Manual de usuario

Coemar

Coemar Panorama Power MK2 Manual de usuario

Coemar

Coemar par lite LED IP Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario