Code Alarm PROFESSIONAL SERIES Manual de usuario

PROFESSIONAL

SERIES

Security and Keyless Entry

Installation Guide

ca1155

**This guide is a reference for module rmware version 5.0 or higher**

2ca1155 rev B

Before You Begin.........................................................................................3

Wire Connection Guide............................................................................... 4

12 Pin Main Harness ................................................................................. 5

10 Pin Input / Output Harness ................................................................... 8

Door Locks .............................................................................................. 11

Additional Ports.........................................................................................12

LED Port ..................................................................................................12

Programming Port ...................................................................................12

Shock Sensor Port ..................................................................................12

DBI Port ...................................................................................................12

Set Up & Programming ............................................................................. 13

Transmitter Programming ........................................................................13

Manual Feature Programming ................................................................. 13

Programming Feature Banks .................................................................. 14

PC Based Feature Programming / Firmware Updates - (Optional) ......... 15

Adjusting the Shock Sensor .................................................................... 16

Testing the Shock Sensor ........................................................................16

Dome Light Delay / Theater Dimming ..................................................... 16

Chirp Delete - User Accessible ................................................................ 17

User Selectable LED ...............................................................................17

Feature Descriptions................................................................................. 17

Transmitter Button Functions .................................................................. 22

Security Trigger Zones.............................................................................. 22

System Layout...........................................................................................23

Table of Contents

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle

during installation

Avoid mounting components or routing wires near

hot surfaces

Avoid mounting components or routing wires near

moving parts

Tape or loom wires under hood for protection and

appearance

Technical Support (800) 421-3209

or go to

www.voxxuniversity.com

Use a Digital Multi Meter for testing and verifying

circuits. DO NOT USE A TEST LIGHT, OR

“COMPUTER SAFE PROBE” as these can set o󰀨 air

bags or damage vehicle computers.

Use grommets when routing wires through metal

surfaces

BEFORE YOU BEGIN

4ca1155 rev B

10 Pin Input / Output Harness

12 Pin Main Harness

1BROWNSIREN OUTPUT ( + )

2REDBATTERY 12V ( + )

3BLACKGROUND

4BROWN/BLACKUNLOCK SWITCH ( 87A )

5VIOLET/BLACK UNLOCK POLARITY ( 87 )

6WHITE/BLACKLOCK SWITCH ( 87A )

7GREEN/BLACK LOCK MOTOR ( 30 )

8WHITE PARKING LIGHT OUTPUT

9WHITE/REDPARKING LIGHT INPUT

10 WHITE PARKING LIGHT OUTPUT

11 VIOLET LOCK POLARITY ( 87 )

12 BLUE/BLACK UNLOCK MOTOR ( 30 )

12 PIN MAIN - POWER / LOCKS

1PURPLE DOOR TRIGGER INPUT ( + )

2GREEN/BLACK FACTORY DISARM OUTPUT ( - )

3OPEN

4GREEN DOOR TRIGGER INPUT ( - )

5ORANGE GROUND WHEN ARMED OUTPUT ( - )

6BROWN/BLACKHORN OUTPUT ( - )

7VIOLET/BLACK AUX 1 ( - )

8GRAY HOOD PIN INPUT ( - )

9YELLOWIGNITION INPUT ( + )

10 RED/WHITETRUNK RELEASE OUTPUT ( - )

10 PIN INPUT / OUTPUT

12 Pin Main Harness

1 BROWN SIREN OUTPUT ( + )

Locate a suitable mounting location in the engine compartment for the siren, away

from moving parts.

With the bell of the siren aiming downwards, secure the siren in place using self

tapping screws, being careful not do drill into any hoses, wiring or components.

Connect the BLACK siren wire to a chassis ground using a ring terminal and self

tapping screw (not supplied).

Route the BROWN siren output wire from the control module through the rewall and

connect to the RED wire on the siren.

NOTE: Be sure to loom the siren wires, and seal the grommet.

3 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and

self tapping screw (not supplied). Scrape away paint from the grounding point to

ensure a good connection. The recommended grounding point is a metal surface in

the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

2 RED BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

 Verication:This wire will register ( + ) voltage in all positions of the ignition

switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

6ca1155 rev B

8 WHITE PARKING LIGHT OUTPUT

9 WHITE/RED PARKING LIGHT INPUT

10 WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

  Verication: This wire registers positive voltage when the parking lights

are turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

4 BROWN/BLACK UNLOCK SWITCH ( 87A )