Code Alarm Ca4054 Manual de usuario

1../.1

i=l

i=»PlOFESSIONAI

SEPliES

Remote Start

Installation Guide

for models:

ca4054

ca4554

Before You Begin.........................................................................................3

Wire

Connection

Guide...............................................................................4

4 Pin Main Harness ...................................................................................5

3 Pin Parking Light Harness......................................................................6

6 Pin Start Harness ...................................................................................7

4 Pin Alternate Harness.............................................................................8

2 Pin Door Lock Output Harness...............................................................9

Additional

Ports.........................................................................................10

Antenna I LED I Programming Port........................................................ 1

OBI

Port...................................................................................................10

Telematic Interface Port...........................................................................10

Set Up

Programming

.............................................................................

Transmitter Programming........................................................................

Manual Feature Programming.................................................................

Programming Feature Banks ..................................................................12

Tach Programming ..................................................................................14

Smart Tachless Mode..............................................................................14

Feature

Descriptions

.................................................................................15

Transmitter

Button

Functions

..................................................................19

2 Way

Transmitter

Notifications

...............................................................20

Remote Start

Shutdown

Diagnostics

......................................................20

System

Layout

...........................................................................................

ca4054 -4554 Install rev A

BEFORE YOU BEGIN

FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.

•

...

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Roll down window to avoid locking keys

vehicle

during installation

Avoid mounting components or routing wires near

hot surfaces

Avoid mounting components or routing wires near

moving parts

Tape or loom wires under hood for protection and

appearance

Use a Digital Multi Meter for testing and verifying

circuits. DO NOT USE A TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air

bags or damage vehicle computers.

Technical Support (800) 421-3209

or go to

http://avxtech1.com

(f)

Zl-

-I

a..

C")

0:::

(f)

0:::

-(.)

a..o

N_J

4 Pin Main Harness

BLUE/BLACK

START

STATUS

ACTIVE OUTPUT ( - )

PURPLE/WHITE TACH INPUT

GRAY

HOOD

PIN INPUT

(-)

BROWN/RED

BRAKE

INPUT ( + )

3 Pin Parking Light Harness

BLACK GROUND

WHITE/RED PARKING LIGHT INPUT

WHITE

PARKING LIGHT OUTPUT

6 Pin Start Harness

PURPLE STARTER

OUTPUT-

MOTOR SIDE

RED BATTERY 12V (

ORANGE ACCESSORY 1 ( + )

PINK/WHITE IGNITION 2 ( + )

RED/WHITE BATTERY 12V (

PINK IGNITION 1 ( + )

4 Pin Alternate Output Harness

BLACK/YELLOW

PULSE

DURING

CRANK

( - )

GREEN/WHITE

PULSE

AFTER

SHUTDOWN

( - )

LT BLUE FACTORY

ARM

PULSE

AFTER

START

)

GREEN/BLACK

FACTORY DISARM

PULSE

BEFORE

START

( - )

2 Pin Lock Output Harness

BLUE UNLOCK

(-)

OPEN

ca4054-

4554 Install rev A

4 Pin Main Harness

1 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )

This wire provides a ground output when the remote start function is activated and

remains until 4 seconds after the remote start is shutdown. Ifthis wire will be used

for multiple application's a 1 amp diode is required in-line with the stripe facing the

control module.

2 PURPLE/WHITE TACH INPUT

Locate the vehicle's ignition coil or fuel injector

the engine compartment.

Verification: Test using the following procedure:

Set voltmeter to AC VOLTS.

Attach positive lead

a volt meter to a constant 12-volt source.

Attach negative lead

a volt meter to the wire to be tested.

4. Start the engine.

Have someone press on the gas pedal slightly as you monitor the meter. If

connected to the correct wire, the voltage reading will increase as the engine's

RPM increases.

Connect the PURPLE/WHITE wire to the negative side

the vehicle ignition coil or

fuel injector.

3 GRAY HOOD PIN INPUT

(-)

Install a Hood Pin Switch and connect to the GRAY wire. This connection is required

for Remote Start.

Verification: This wire when connected will register ground when the

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE: Be sure to loom the wire, and seal the grommet.

BROWN/RED

BRAKE INPUT ( + )

Locate the vehicle's brake light wire at the brake pedal mounted switch. This

connection is required for Remote Start.

Verification:

This wire registers positive voltage when the brake pedal is

pressed.

Connect the

BROWN/RED

wire to the vehicle's brake light wire.

3 Pin Parking Light Harness

BLACK

GROUND

Connect the

BLACK

wire to a solid chassis ground point using a ring terminal and

self tapping screw (not supplied). Scrape away paint from the grounding point to

ensure a good connection.

The

recommended grounding point is a metal surface in

the driver's side kick panel area.

NOTE:

Do not ground the

BLACK

wire with any other vehicle components.

WHITE/RED

PARKING LIGHT

INPUT

WHITE

PARKING LIGHT

OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification:

This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the

WHITE/RED

wire to a 15

Amp

max

fused battery source.

Connect the

WHITE

wire to the parking light output wire.

Negative switching Parking Lights:

Connect the

WHITE/RED

wire to a good chassis ground.

Connect the

WHITE

wire to the parking light output wire.

ca4054-

4554 Install rev A

6 Pin Start Harness

1 PURPLE STARTER

OUTPUT

( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage onlywhen the key is turned to the

START position.

Connect the PURPLE wire to the

MOTOR

SIDE

the vehicle starter wire.

2 RED BATTERY

12V

(

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions

the ignition

switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

ORANGE

ACCESSORY

1 ( + )

Locate the vehicle's accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to ACC

(Accessory) and the ON (or RUN) position. The voltage drops out when the

key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

4 PINK/WHITE IGNITION 2 ( + )

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position, but not the

ACC

(Accessory) position.

The

voltage does not

drop out when the key is turned to the START (or

CRANK)

position.

Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.

Programmable output: IGN, ACC, Start.

5 RED/WHITE BATTERY 12V (

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage

all positions

the ignition

switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

6 PINK IGNITION 1 (

Locate the vehicle's ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position.

Connect the PINK wire to the vehicle's Ignition wire.

This wire is also used for Ignition 1 Output.

4 Pin Alternate Output Harness

GREEN/BLACK FACTORY DISARM I

PULSE BEFORE START ( - )

This wire will supply a ( - ) 200mA pulse both upon disarming the system and when

the remote start feature is activated. Locate the factory perimeter alarm disarm wire

from the key cylinder inside the drivers door.

Verification: This wire registers ground ifthe key is turned to the unlock

position

the driver's door cylinder.

This output is configurable

option programming.

BLUE FACTORYARM I

PULSE AFTER START ( - )

This wire will supply a

(-)

200mA pulse upon successful completion

the remote

start activation sequence and is typically used to re-lock the vehicle's doors upon

remote start if necessary.

This output is configurable

option programming.

ca4054 -4554 Install rev A

3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

This wire will supply a

(-)

200mA

pulse after the remote start shuts down. This

is typically used to re-lock the vehicle's doors

they unlock upon remote start

shutdown.

can also be used to pulse a door pin-switch wire to prevent the vehicle's

accessories from remaining on after remote start shutdown.

This output is configurable in option programming.

4 BLACK/YELLOW PULSE DURING

CRANK

(-)

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only

the start (crank) position

the ignition switch.

This wire will supply a ( - ) 200mAoutput and can be configured

option

programming.

2 Pin Lock Output Harness

1 BLUE UNLOCK

(-)

The door unlock output wire provides an output only while the remote start feature is

active.

Additional Ports

Antenna I LED I Programming Port

Mount the supplied antenna/receiver to a clear spot

the vehicle's windshield that

will not block the driver's vision. A good location

usually high

the windshield

near the rear view mirror.

careful not to mount the antenna/receiver

any

metallic window film, as this will effect system range. Route the antenna/receiver

cable to the control module and plug into the antenna port.

Data Bus Interface Port

This 4

port

used for Flashlogic Door Lock and Transponder Databus Interfaces

communicate with the vehicle's Databus. When using the

OBI

port to control the

Flashlogic Door Lock and Transponder Interface modules the following options may

available. Please refer to the

020

(Data to Data) function list available per vehicle

the tech service web site.

Tach

Input Brake Safety Shut Down

Trunk/Hatch Open Diesel Glow Plug Input

Door Lock Control Passlock I Passkey Interface (GM Only)

Dome Light Supervision Transponder Interface Activation

Factory Alarm Arm I Disarm Manual Arm I Disarm Inputs (factory keyless

controls system)

Telematic Interface Port -CA4554 ONLY

This 4 pin port

used for Telematic Interface accessories, such

Car Connection

Pro, which can control some ofthe following features.

Door Unlock Control Trunk Release

Sliding Doors

Car Find AUX Output

Remote Start

ca4054-

4554 Install rev A

Otros manuales para ca4054

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arranque remoto de Code Alarm

Code Alarm

Code Alarm ca5153 Manual de usuario

Code Alarm

Code Alarm CSM-3 Manual de usuario

Code Alarm

Code Alarm CA 5150 Manual de usuario

Code Alarm

Code Alarm CA-520A Manual de usuario

Code Alarm

Code Alarm Professional Series CA 6550 Manual de usuario

Code Alarm

Code Alarm CA 5051MT Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm ca6554 Manual de usuario

Code Alarm

Code Alarm RCS2 Manual de usuario

Code Alarm

Code Alarm CA-630 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm Professional Series CA 5050 Manual de usuario

Code Alarm

Code Alarm Professional Series CA 1050 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm CA 5150 Manual de usuario

Code Alarm

Code Alarm CA-500 Manual de usuario

Code Alarm

Code Alarm professional series PROCOMP Manual de usuario

Code Alarm

Code Alarm CSM-3 Manual de usuario

Code Alarm

Code Alarm CA 421 Manual de usuario

Code Alarm

Code Alarm ca 1051 Manual de usuario

Code Alarm

Code Alarm CA 5051 Manual de usuario

Code Alarm

Code Alarm PC 7600 Manual de usuario

Code Alarm

Code Alarm PC 4300 Manual de usuario

Code Alarm

Code Alarm CA 440SS Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual

Rooboost

Rooboost RB-1750WP Manual de usuario

Code Alarm ca4054 Manual de usuario

Manuales populares de Arranque remoto de otras marcas