Cobb AP-SUB-003 Manual de usuario
User Guide
Subaru Turbo
(North American Models)
Page 2
Table of Contents
Product Introduction 4
Supported Vehicle List
In-Box Contents 5
What Is A Map? 7
AccessPORT Installation 8
Pre-Installation 8
Getting Started 9
Vehicle Identification 11
Map Selection 11
Save Stock ECU Program Data 12
Install AccessPORT Programming 12
Installation Complete 13
AccessPORT Features & Functionality 14
Monitor 1
Live Data 1
Data Log 1
Fuel Economy 15
Set Rev Warning 15
Set Live Data List 15
Set Data Log List 16
Reset Live List 16
Reset Log List 16
Reset Fuel Econ. 16
Performance 17
0-60 MPH 17
¼ Mile 17
Dynamometer 17
Reset Dyno 17
Tune 18
Change Map 18
Adjustments 18
Show Current Map 19
Revision 1.079 Nov 1 , 2013
Page 3
Troubleshooting 20
Reset ECU 20
Read Codes 20
Memory Snapshot 20
AccessPORT 21
About 21
Settings 21
Uninstall 21
AccessPORT Troubleshooting 22
AccessPORT will not communicate with vehicle. 22
AccessPORT cannot reflash ECU. 22
AccessPORT cannot identify vehicle during installation. 22
Support Contact Information 22
Web 22
E-Mail 22
Phone 22
nvironmental Information 23
Revision 1.079 Nov 1 , 2013
Product Introduction Page
Product Introduction
Congratulations on the purchase of the new AccessPORT hand held programmer. The
AccessPORT can:
●Reprogram the factory engine control unit (ECU) with improved tuning parameters
through the on-board diagnostic (OBD-II) port
●Monitor and log vehicle sensor data using on-screen digital gauges
●Read and clear engine diagnostic trouble codes (DTCs)
●Measure 0-60 and ¼ mile times and dyno plot
●Estimate instantaneous and average fuel economy
●Adjust idle and timing
Supported Vehicle List
●200 – 2013 Subaru Forester XT (MT & AT)**
●2009 – 2010 Subaru Impreza 2.5GT (AT)**
●2002 – 201 Subaru Impreza WRX (MT & AT)**
●200 – 201 Subaru Impreza STI**
●2005 – 2012 Subaru Legacy GT (MT & AT)**
●2005 – 2009 Subaru Outback XT (MT & AT)**
** designed for and sold in North America only
Revision 1.079 Nov 1 , 2013
Product Introduction Page 5
In-Box Contents
AP-SUB-001 AP-SUB-002 and AP-SUB-003
AccessPORT Version 2
-OR-
AP-SUB-001
AP-SUB-002 and AP-SUB-003
AccessPORT Version 2b
Revision 1.079 Nov 1 , 2013
Product Introduction Page 6
WARNING!
Installation and use of the AccessPORT may void all or a portion of
the vehicle manufacturer's standard warranty. There is no guarantee
expressed or implied by COBB Tuning or any of its affiliates for the
use of the AccessPORT. The user accepts all risks and
responsibilities when using the AccessPORT.
WARNING!
Use of the AccessPORT while operating a moving vehicle is strictly
prohibited by law. COBB Tuning and its affiliates accept no
responsibility for damages or injury caused by misuse of the
AccessPORT.
WARNING!
The AccessPORT may not be able to function if the vehicle's wiring
has been modified. If problems occur while using the AccessPORT,
please verify that all wiring to and from the CU is correct and
functional.
Revision 1.079 Nov 1 , 2013
Product Introduction Page 7
What Is A Map?
The AccessPORT reprograms the tuning parameters inside the factory engine control unit
(ECU) using map files, which contain specially written instructions for the AccessPORT to
follow during the reprogramming process. A map file can contain information for any number
of different modifications or enhancements to a vehicle, ranging from a race map for a
heavily modified vehicle to an economy map for a stock vehicle. Through the use of the
AccessPORT and different map files the ECU can be reprogrammed to accommodate
virtually any vehicle configuration.
Revision 1.079 Nov 1 , 2013
AccessPORT Installation Page 8
AccessPORT Installation
Pre-Installation
The AccessPORT comes with the most up-to-date software and map files available at the
time of shipment. However, it is possible that updated software and/or map files have been
made available since the time of shipment. Therefore, the recommended procedure is to
connect the AccessPORT to the AP Manager software and download the latest software and
map files for the target vehicle. Please see AP Manager Software Manual for more
information.
IMPORTANT!
For installation purposes, it is important to ensure that the vehicle's battery has
adequate power for both the AccessPORT and the CU. Because of this, it is
recommended that all in-car electronics and vehicle lights are turned off during
the installation process to reduce drain on the vehicle's battery. For improved
safety during installation, a car battery charger can be connected to the vehicle
during the installation process.
Revision 1.079 Nov 1 , 2013
AccessPORT Installation Page 9
Getting Started
1. Insert the key into the vehicle's ignition and leave it in the OFF position.
2. (AP-SUB-001 and AP-SUB-002 owners only):
Locate the green Test Mode connectors. Impreza and Forester models will have this
located under the driver's side dash to the left of the steering column (see left
diagram). The Legacy and Outback models will have this located on the passenger
side (see right diagram). With the connectors located, enable Test Mode by plugging
the two connectors into each other.
NOT : In the event that the vehicle does not enter Test Mode after plugging in the
green connectors, refer to [TROUBL SHOOTING S CTION] .
3. (AP-SUB-001 owners only):
Identify the correct Initialization Connector for your vehicle (2002 WRX = BLUE, 2003
- 2005 WRX = WHITE). Attach the Initialization Connector to the corresponding
connector under the driver's side dash. This connector will be located near the green
Test Mode connectors and will be translucent white in color. Do not proceed until this
step is complete.
Revision 1.079 Nov 1 , 2013
AccessPORT Installation Page 10
. Locate the vehicle's OBD-II port. Location of the OBD-II port may vary depending on
the vehicle model..
5. Connect device to the OBD-II port.
a) (AccessPORT Version 2 only):
•Connect the small end of the provided USB
cable to the mini-USB port on the back of the
OBD connector.
•Plug the large end of the USB cable into the
standard USB port on the underside of your
AccessPORT. At this point the AccessPORT
will power up and after a few moments
present the installation menu.
b) (AccessPORT Version 2b only):
•Plug the OBD-II cable into the OBD-II port
under the dash.
•Connect the other end of the OBD-II cable
to the 10-pin port on the bottom of the
AccessPORT. At this point the
AccessPORT will power up and after a few
moments present the installation menu.
Revision 1.079 Nov 1 , 2013
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Electrónica del automóvil de Cobb
