Clevertronics L10 LLIFE-PRO-WP-IPREM Instrucciones de instalación y funcionamiento

1942376

V1.4

10 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

The front cover will require removal to gain access to the Test/Status Switch and LED.

Maintained fittings ((LLIFEM-PRO-WP—ss-xx-IPREM-yy-uu)) cannot be scanned with a camera using

the CleverSparky App as the maintained light source interferes with the camera scanning function. To

and enter manually into CleverSparky.

Zoneworks, HIVE (HV/HVG) and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also

be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, HVG,

DATA

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire, please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

LLIFE-PRO-WP-IPREM

Remote Mount Weatherproof Emergency Luminaire

Installation & Maintenance Instruction Leaflet

Remote Control Gear

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements

of AS2293.3: 2005 and AS/NZS CISPR15: 2017

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

LLIFEz-PRO-WP-ss-xx-IPREM-yy-uu

Testing:

Options:

Manual Test

xx = Blank

Non-Maintained

z=Blank

Zoneworks

xx = ZW

Maintained

z=M

Z/W DATA

xx = DATA

Tamperproof

yy=TP

Zoneworks HIVE

xx = HV/HVG

Custom Option

DALI Registered.

xx = DALI

Vent

Clevertest

xx = CT

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest PLUS

capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1530230

Replacement Battery

1100697

Replacement Emergency LED Board

1100702

Replacement Emergency LED Board (Black)

AUM01370120001

Replacement Emergency Driver

AUM01370230001

Replacement Emergency Driver Maintained

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942376

V1.4

10 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Installation:

This LLIFE-PRO Surface mount Weatherproof Emergency Luminaire can be installed on any solid or T-

BAR ceilings or used to replace an existing unit.

•Locate the installation position for each enclosure.

•Remove the enclosure covers.

•Pre-drill mounting holes per diagram below.

•Drill a hole in each enclosure to suit the cable gland or conduit to be used for LED cable entry.

•Drill a suitable hole in the Control Gear enclosure for power entry.

•Use suitable fixings to fasten each enclosure to the mounting surface.

•Route the interconnecting cable between the Control Gear and the LED lamp. For distances over 2

metres, an appropriate fire rated cable must be used.

•Connect the LED interconnect cable to the terminal block inside each enclosure. Be sure to match

the colour code between the two terminal blocks.

•Connect the LED cable and battery to the control gear inside the control gear enclosure.

•Connect the power to the mains.

•Screw the covers to the enclosure bases

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four

Segment Marking on the product will include an ‘’F’’ in third segment block.

•Apply power and test the fitting.

•(Applicable to -VENT products only) If the products are installed in a Wall Mounted fashion,

please ensure that the Pressure Equalization Vents are facing downwards, upon product

installation.

Networking:

When installing the product on a monitored network, (ZONEWORKS, HIVE, DATA, DALI) simply insert

the relevant Smart Node PCA.

Dimensions:

Testing:

When the unit is connected to the un-switched active, it must be allowed to charge the battery for at

least 24 hours. The emergency lamp only illuminates during a power failure. Conduct the following tests:

•During the first commissioning test the emergency lamp must illuminate for at least 2 hours after

disconnection from the main supply. The results of all tests are required to be recorded in a service

logbook, which is to be kept on-site at all times. If the unit fails to illuminate for the requisite time,

remedial action must be taken to repair the situation and once completed, the unit must pass a

subsequent test.

•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.

•Release the Test Button or Switch on Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1, not applicable

for –TH (theatre) version (refer to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics Glider Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT PRO Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LJELED-40 Series Manual de usuario

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP LIFELIGHT Pro Manual de usuario

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CBS2LEDS-DIF Series Especificaciones técnicas

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manual de usuario

Clevertronics

Clevertronics LP CUBPRO Series Manual de usuario

Clevertronics

Clevertronics TS Trade Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ELIFE-X-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LBS2N Series Manual de instrucciones

Clevertronics

Clevertronics L10 CleverFit Exit LCFLED Series Manual de usuario

Clevertronics

Clevertronics L10 LJWELED-40 Series Manual de usuario

Clevertronics

Clevertronics LP CBS4LEDS DIF Series Especificaciones técnicas

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manual de usuario

Clevertronics

Clevertronics LP CFLLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Trade Series Manual

Clevertronics

Clevertronics FBKLED Series Manual de instrucciones

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics l10 LBULKy Series Instrucciones de instalación y funcionamiento

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario