Clevertronics LP CCIRC Series Instrucciones de funcionamiento y mantenimiento

1942498

V1.2

20 May 2022

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Note: To scan the Status LED on the luminaire, the diffuser will require removal.

Status LED Note:

The Status LED is High Brightness and may appear as two separate spots as

illustrated. If Red and Green are seen at the same time, this needs to be taken

as Yellow in the Cleverest Plus operation guide.

Zoneworks, HIVE and DATA Monitored Options

Fittings with part numbers -ZW, -HV/-HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can

also be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by

a single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator

provides a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, HVG,

DATA Commissioned LED on Solid (Green)

ZW, DATA Un-commissioned Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS,

green 250mS, yellow 250mS, green

250mS, green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In

Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In

Progress LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection

to the DATA network via a multi-drop bus (daisy chain connection). For further information of

installation of a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning

Guide (incl. DATA version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

luminaire will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned LED on Solid (Green)

Emergency Light Test in progress LED flashes at 1s On (red & green) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way

“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections

are marked as Da Da.

LP™ Circular Emergency Light

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the

requirements of AS/NZS 2293.3 2018 and AS/NZS

CISPR15: 2017

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to

the operation guide supplied with the product for details.

Models:

CCIRC-yy-xx

Testing:

Options:

Manual Test

xx = Blank

DALI Driver

yy = DD

Zoneworks

xx = ZW

Hi/Lo Control through

Microwave Sensor

yy = MS-HL

Z/W DATA

xx = DATA

DALI Registered.

xx = DALI

Hive

xx = HV/HVG

Spare Parts:

1550010

Replacement Battery

8011800

Replacement Emergency LED

1330091

Replacement 240V Driver

AUM02870500001

Replacement Emergency Driver (-HV)

AUM02370470001

Replacement Emergency Driver

AUM02970150001

Replacement Emergency Driver (-HVG)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

Note:

This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-user

replaceable light source and battery - to be replaced (if required, refer installation instructions for

battery/lamp replacement) by Clevertronics service personnel/agents or a registered electrician.

1942498

V1.2

20 May 2022

Installation:

The Circular can be installed in either a ceiling mounted or wall mounted configuration.

•Remove the diffuser by rotating it counter-clockwise.

•Remove the gear-tray by loosening the 3 screws holding it in place and then slightly rotating the

gear-tray clockwise to release it from the keyhole slots.

•The power cable entry to the luminaire is via the rear surface of the base through the existing

20mm hole. Ensure appropriate cable entry provisions are made on the installation surface for this

purpose.

•The base of the luminaire can be mounted to the installation surface with the use of suitable

fasteners (Not provided). These fasteners should be placed through the mounting feet of the base

of the luminaire.

•Route the power cable into the base via the existing 20mm hole at the rear of the base during the

installation of the base.

•Secure the gear-tray to the base by connecting the lanyard extending from the base to the gear-

tray.

•Connect the 240VAC (N, AEM, ASW, Earth) supply to the terminal block of the gear tray. (For DALI or

DATA luminaires, terminate the additional wires to the appropriately marked terminals.)

•Secure the gear-tray to the base via the keyhole slots on the gear-tray and by tightening the 3

screws.

•Fit the diffuser to the base by placing the diffuser over the base and then rotating it clockwise,

ensuring all the slide-lock points are engaged.

•Apply power to the luminaire and test as per the instructions.

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and

update the Four Segment Marking on the product to include a ‘’F’’ in third segment block.

Dimensions:

Complete luminaire outer dimensions:

327mm (Diameter) x 100mm (Max Height)

Base Diameter:

272mm

Rated Emergency Lumen Output in accordance with AS/NZS 2293.1 (refer to spacing

tables for installation positions): Refer to the Technical Label for classification information.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Testing:

Once connected to the 240V mains supply, the luminaire must be allowed to charge the battery for at

least 24 hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours (4 hours for -

4HR luminaires) after disconnection from the mains supply.

•Subsequent tests require the luminaire to illuminate for at least 90 minutes. The results of all tests

are required to be recorded in a service logbook, which is to be kept on-site at all times. If the

luminaire fails to remain illuminated for the requisite time, remedial action must be taken to repair

the situation and once completed, the luminaire must pass a subsequent test. For more specific

information, please refer to the current edition of the AS/NZS 2293.3 Standard.

Maintenance

Use only the Lamp or Battery recommended on the technical label inside the Circular.

Prior to any work, isolate the power to the luminaire that requires Lamp or Battery replacement.

Lamp Replacement:

•Remove the diffuser by rotating it counter-clockwise to access the lamp module. If the battery

continues to power the LED Module, then remove the gear-tray by loosening the 3 screws holding

it in place and then slightly rotating the gear-tray clockwise to release it from the keyhole slots.

Disconnect the battery connector from the Emergency Driver. Then refit the gear-tray to the base.

•Gently push into the top of the wiring terminals and pull out the wires from the LED Module.

•Un-do the 4 Philips head screws to disengage the LED module from the gear-tray.

•Fit the new LED Module to the gear-tray by following the above process in reverse. Ensure the

battery connector is refitted, if it was removed during the lamp replacement process.

Maintenance - Battery Replacement:

•Obtain access to the rear side of the gear-tray by removing the diffuser by rotating it counter-

clockwise; Then remove the gear-tray by loosening the 3 screws holding it in place and then slightly

rotating the gear-tray clockwise to release it from the keyhole slots.

•Disconnect the battery connector from the Emergency Driver.

•Un-do the 2 Philips head screws to remove the battery and then replace it with the new battery,

ensuring that the tooth-washers are re-used.

•Fit the battery connector to the Emergency Driver.

•Refit the gear-tray and diffuser by following the above process in reverse.

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Luminaires on these circuits will have their batteries

discharged or “cycled”. The battery in this luminaire has been selected to give excellent long-life

performance in a controlled AS/NZS 2293.1 testing environment. Excessive battery cycling will reduce

through-life performance and may lead to premature battery failure. Battery warranty claims, as a result

of such abuse are specifically EXCLUDED from Clevertronics warranty terms.

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics L10 Argonaut PLUS Manual de usuario

Clevertronics

Clevertronics FBKLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Lifelight Pro LWPLIFE-PRO-WM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Manual de usuario

Clevertronics

Clevertronics LED CIRCLITE Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CBS4LEDS DIF Series Especificaciones técnicas

Clevertronics

Clevertronics LP CSBLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CleverEVAC L10 Cleverfit Pro DYRL CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Manual de instrucciones

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP CCFPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics EL EUBPRO-SM-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics TS Trade Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ECFLED-LI-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE-PRO-SMS-SPOT Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP LIFELIGHT Pro Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario