Clear-Com RS-602 Manual de usuario
RS-602/622
BELTPACKS
INSTRUCTION MANUAL
RS-602/622 Instruction Manual
©2005 Vitec Group Communications Inc.
All Rights Reserved
Part Number 810288, Rev. B
Vitec Group Communicatons
4065 Hollis Street
Emeryville, CA 94608-3505
U.S.A
Clear-Com is a registered trademark of Vitec Group
Communications
The Clear-Com Logo is a registered trademark of Vitec
Group Communications
Windows is a registered trademarks of Microsoft Corp.
RS-602/622 BELTPACK 1
CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
QUICK START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OPERATING YOUR BELTPACK . . . . . . . . . . . . . . . . . . . . 5
Beltpack Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Controls and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONNECTING YOUR BELTPACK . . . . . . . . . . . . . . . . . . 17
Intercom Connector . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Loop-Through Connector . . . . . . . . . . . . . . . . . . . . . 20
Program-Audio Volume Control . . . . . . . . . . . . . . . . 21
Auxiliary (“AUX”) Headphone . . . . . . . . . . . . . . . . . . 21
Headset Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CUSTOMIZING YOUR BELTPACK . . . . . . . . . . . . . . . . . . 25
V-Pack Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Onboard Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Understanding Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting a Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2 R S - 6 0 2 / 6 2 2 B E L T P A C K
Editing a Mode’s Settings. . . . . . . . . . . . . . . . . . . . . . . . . 30
Restoring the Factory Default Settings. . . . . . . . . . . . . . . 31
Settings You Can Customize . . . . . . . . . . . . . . . . . . . . . . 32
Mode Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Latch Disable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Call-on-Talk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Electret Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Audible Call Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Channel Swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Channel Exclusive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Split-ear Headset (RS-622 only) . . . . . . . . . . . . . . . . . 36
Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 37
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RS-602/622 BELTPACK 1
INTRODUCTION
Thank you for choosing this product. Clear-Com designed the 600
series of beltpacks to meet the needs of all beltpack users, from
beginners to experienced professionals. For advanced users, the 600
series provides the most advanced level of functioning available.
You can choose from among seven different versions of beltpacks,
including single and dual-channel units, featuring both Clear-Com
and TW (two-wire) compatibility.
RS-600 SERIES
All RS-600 series beltpacks offer the following features:
• Rugged, compact design
• Full compatibility with all existing Clear-Com party-line
systems
• Four setup configurations that you can activate directly from
the beltpack
• Extra 2.5 mm cell-phone type headset jack
• Advanced setup options with V-Pack software
2 RS-602/622 BELTPACK
RS-602 AND RS-622 BELTPACKS
The RS-602 and RS-622 beltpacks add the following features:
• Two intercom channels
• Local input for program audio
• “Loopable” program audio; you can connect program audio to
other beltpacks in a “daisy-chain” configuration
• Program audio volume control
• RS-602 offers monaural headset connector
• RS-622 offers binaural headset connector
• 6-pin Switchcraft-style intercom connectors
RS-602/622 BELTPACK 3
QUICK START
To start using your beltpack immediately:
1. Connect the appropriate 6-pin XLR line cables from an
active intercom line to the beltpack.
Note: The beltpack’s intercom connectors use the Switchcraft-style
6-pin configuration. If ordering Neutrik 6-pin plugs to make a
cable or patch panel, specify that you need the Switchcraft pin
configuration. This configuration usually has an “S” suffix at the
end of the Neutrik model number.
2. Turn down the beltpack’s incoming volume on each intercom
channel with the channel A and channel B volume-control
knobs.
3. Plug in a headset equipped with a dynamic microphone to
the beltpack’s main headset jack.
The headset jack is labeled on the back of the beltpack.
4. To talk on an intercom channel, press and hold the talk
button for the desired channel. Speak into the microphone in
your headset.
Note: If you tap the talk button twice in quick succession, the
talk button locks to the “on” setting (“latches”) for hands-free use.
Press the talk button again to unlatch it.
RS-602/622 BELTPACK
4
5. Adjust the sidetone and incoming volume levels
for both channels as you and others on the
channels speak at the anticipated levels for the
application.
6. To send a call signal, press the button labeled
“call” for the appropriate channel.
5
RS-602/622 BELTPACK
OPERATING YOUR BELTPACK
BELTPACK COMPATIBILITY
The RS-602 and RS-622 beltpacks work with all
previous versions of standard Clear-Com party-line
stations and beltpacks, as long as you use proper cabling
and 6-pin connectors. These models are not designed
for use on a two-wire (TW) line. If you use these
beltpacks on a TW line, the audio on channel A of the
TW line will be lost.
The RS-603 series of beltpacks operate on TW lines.
See the RS-603 series manual for more information.
CONTROLS AND ADJUSTMENTS
Figures 1 and 2 illustrate the beltpack’s onboard controls
and adjustments.
Talk Lights, Channels A and B
A channel’s green talk light illuminates when you press
or latch that channel’s talk button.
1
6 RS-602/622 BELTPACK
Some onboard programming options can change the
function of this light. For more information about
onboard programming, refer to the chapter
“Customizing Your Beltpack.”.
Figure 1: RS-602/622 Control Panel
$BMMMJHIUTDIBOOFMT"BOE#
$BMMCVUUPOTDIBOOFMT"BOE#
5BMLMJHIUTDIBOOFMT"BOE#
5BMLCVUUPOTDIBOOFMT"BOE#
CALL A
TALK A
TAL K B
CALL B
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Clear-Com
Clear-Com
Clear-Com TEMPEST 2400 Manual de usuario
Clear-Com
Clear-Com EclipseHX Manual de instalación y operación
Clear-Com
Clear-Com Eclipse HX-PiCo Manual de usuario
Clear-Com
Clear-Com PM-220 Guía de solución de problemas
Clear-Com
Clear-Com ICS-102 Manual de usuario
Clear-Com
Clear-Com HBP-2X Guía de inicio rápido
Clear-Com
Clear-Com HME DX410 Manual de usuario
Clear-Com
Clear-Com FreeSpeak II Manual de usuario
Clear-Com
Clear-Com Tempest2400 Manual de usuario
Clear-Com
Clear-Com Eclipse HX-Median Manual de usuario
Clear-Com
Clear-Com RS-700 Series Manual de usuario
Clear-Com
Clear-Com Matrix Plus 3 Manual de usuario
Clear-Com
Clear-Com HelixNet Partyline Manual de usuario
Clear-Com
Clear-Com RS-601 Manual de usuario
Clear-Com
Clear-Com eclipse HX-Delta Manual de usuario
Clear-Com
Clear-Com KB-111A Guía de solución de problemas
Clear-Com
Clear-Com ECLIPSE EASI-PICO MATRIX Manual de usuario
Clear-Com
Clear-Com DX410 Manual de usuario
Clear-Com
Clear-Com ECLIPSE ICS 92/52 Manual de usuario
Clear-Com
Clear-Com Encore V-Box Manual de usuario
