Clarke CAR8P Manual de usuario
HOSE REEL
MODEL No: CAR8P & CAR15P
INSTRUCTIONS FOR USE
0405
Thank you for purchasing this Clarke Hose Reel.
Please read this instruction leaflet carefully before installation, and ensure it is
maintained according to this schedule. In doing so, the Reel will provide you with
many years of satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
Please Note: Seals, Plastic Rollers and rubber Stopper are considered
to be normal wear items and as such are not covered by this warranty
- 2 -
IMPORTANT!
Maximum Operating Pressure
CAR8P .......................... 12 bar / 180 psi
CAR15P ........................ 20 bar / 300 psi
OPERATION
Check Reel for correct operation, as follows:
Gently pull out the hose - a series of clicks will be heard, every half revolution of
the drum.
When a click is heard, release the hose. It should be held by the latch. Continue
to pull out the hose, and after a series of clicks, at various lengths, release it to
check the operation of the latch.
To retract the hose, give it a brief tug to disengage the latch, then allow it to retract
fully, under control, until the stopper rests on the hose guide. DO NOT allow the hose
to retract freely....it must be restrained in order to prevent the air tool, connected to
the end of the hose, from whipping with resultant damage to persons or property.
Model CAR15P is also provided with
a locking device which allows the hose
to be held in any desired position.
Simply slide the latch to the locked
position when required.
To release, give the hose a brief tug,
whilst sliding the latch to the unlock
position, then allow the hose to retract
under restraint.
SAFETY PRECAUTIONS
• Never exceed the rated operating pressure for this device.
• Eye protection should be used when assembling and using the hose reel.
• Take ALL precautions with respect to the use of compressed air.
Remember....compressed air can kill.
• Ensure all air connections are properly sealed using teflon tape or pipe sealant.
• Never allow the hose to retract freely, It should always be restrained to prevent
the air tool from whipping, with resultant damage to persons or property.
• Keep children away from the work site.
INSTALLATION
The Hose Reel assembly may be wall or ceiling mounted. Ensure the mounting
hardware (not supplied) is of sufficient strength to support the Hose Reel assembly
and the forces required to pull out the hose etc.
- 3 -
The swivel seals will need replacing due to normal wear and tear, from time to
time. This is carried out as follows:
A. Model CAR8P
1. Remove the 4 side cover securing
screws ‘A’ and pull off the cover to
reveal the swivel hub -’C’.
2. Undo and remove the swivel hub
securing screws - ‘B’ and pull out the
swivel hub.
3. Renew the single O-Ring seal and
reassemble in reverse order.
IMPORTANT! DO NOT overtighten the
swivel seal securing screws. Damage to
the plastic screw threads is irreparable
Swivel Seal Replacement
MAINTENANCE
Hose Tension Adjustment
Model CAR15P only is provided with a mechanism to adjust the hose tension. This
is achieved as follows:
1. Remove side cover (2 self tapping
screws) to reveal the adjuster plate.
2. Hold the plate steady using a
socket as shown, with ‘T’ bar, whilst
undoing and removing the 4 plate
securing screws.
3. Turn the plate clockwise or anti-
clockwise, to increase or decrease the
tension, as required, then replace the
securing screws. It is possible to move
the plate by increments of 1/8 turns
Before Use
Check the hose for wear and damage, and the swivel fitting for leakage using soapy
water. Any damage or leaks should be repaired before further use.
WARNING: Whenever servicing or carrying out maintenance tasks, ALWAYS
turn OFF the air supply to the Hose Reel and release any pressure in the line.
- 4 -
B. Model CAR15P
1. Remove the three side cover
securing screws, to reveal the swivel
assembly.
2. Tilt the cover, as shown, so that the
swivel connector may be undone
using an M22 spanner.
3. Undo the four screws securing the
plastic cover, then pull out the swivel
connector and replace the O-Ring.
Reassemble in reverse order.
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
PARTS AND SERVICE CONTACTS
- 5 -
No. Description Part No.
1 Screw CAR8P01
2 Side Cover CAR8P02
3 Swivel Connector CAR8P03
4 O-Ring CAR8P04
5 Bolt N/A
6 Screw N/A
7 Outer Casing Inlet side CAR8P07
8 Roller CAR8P08
9 Hose Joint Retainer CAR8P09
10 Drum CAR8P10
11 Fitting CAR8P11
12 Spring CAR8P12
13 Drum Side Plate CAR8P13
14 Shaft CAR8P14
15 Ratchet Pawl CAR8P15
16 Ratchet Shaft CAR8P16
17 Spring CAR8P17
18 Mounting Bracket CAR8P18
19 Outer Casing CAR8P19
20 Pivot Pin CAR8P20
21 Nut N/A
22 Hose CAR8P22
23 Nut N/A
24 Bolt N/A
25 Stop Block CAR8P25
26 Rubber Stop CAR8P26
27 Air Inlet Hose CAR8P27
No. Description Part No.
PARTS - CAR8P
- 6 -
No.Description Part No.
1 Outer Casing - Adj. side CAR15P01
2 Outer Casing - Inlet sideCAR15P02
3 Drum - Air Inlet side CAR15P03
4 Drum - Adjuster side CAR15P04
5 Spring CAR15P05
6 Shaft CAR15P06
7 Ratchet Pawl CAR15P07
9 Spring CAR15P09
11 Locking Ring CAR15P11
15 Spring, Adj. Bushing CAR15P15
16 Stop Block CAR15P16
17 Slipping Block CAR15P17
18 Swivel Conn. Body CAR15P18
19 Hose Clip CAR15P19
20 Bushing CAR15P20
21 Swivel Connector CAR15P21
22 Fitting CAR15P22
23 O-Ring CAR15P23
24 Cover - Inlet CAR15P24
25 Cover - Adjuster CAR15P25
26 Mounting Bracket CAR15P26
27 Pin CAR15P27
29 Roller CAR15P29
30 Hose CAR15P30
31 Ball Stop CAR15P31
32 Hose Clip CAR15P32
35 Retainer CAR15P35
36 Inlet Hose CAR15P36
No.Description Part No.
PARTS - CAR15P
- 7 -
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Herramientas de Clarke
Clarke
Clarke CDS300B Manual de usuario
Clarke
Clarke CHT 455 Manual de usuario
Clarke
Clarke CAT125 Manual de instalación y operación
Clarke
Clarke X-pro CAT164 Manual de instalación y operación
Clarke
Clarke Metalworker CPTN1 Manual de instrucciones
Clarke
Clarke Strong-Arm CFB600 Manual de usuario
Clarke
Clarke CAT33B Manual de instalación y operación
Clarke
Clarke CAT66 Manual de usuario
Clarke
Clarke CHT718 Manual de usuario
Clarke
Clarke CHT 141 Manual de usuario
Clarke
Clarke X-PRO CAT208 Manual de instalación y operación
Clarke
Clarke CHT878 Manual de usuario
Clarke
Clarke Air CHR9P Manual de usuario
Clarke
Clarke TPG30P Manual de usuario
Clarke
Clarke CHT691 Manual de usuario
Clarke
Clarke CRT 40 Manual de usuario
Clarke
Clarke CFC100 Manual de instalación y operación
Clarke
Clarke CONTRACTOR CLJ120 Manual de instrucciones
Clarke
Clarke CHT706 Manual de usuario
Clarke
Clarke CHT204 Manual de usuario
