Clarke CBS190B Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0816

BANDSAW

MODEL NO: CBS190B

PART NO: 6460132

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

INTRODUCTION

Thank you for purchasing this CLARKE Bandsaw.

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Recycle unwanted materials instead of disposing of them as waste. All

unwanted accessories and packaging should be sorted and taken to a

recycling centre for disposal in a manner which is compatible with the

environment.

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste but according to the laws governing Waste Electrical and

Electronic Equipment (WEEE) at a recognised disposal facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS

WORK ENVIRONMENT

1. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Anyone

entering the work area must wear personal protective equipment.

Distractions can cause you to lose control and fragments of work or a

broken disc may fly away and cause injury.

4. Store power tools properly when not in use. Abrasive products should be

stored in a dry, secure place out of the reach of children.

5. Please read these instructions carefully and retain for future reference.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use adapter plugs with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce the risk of electric shock.

2. Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

3. Do not abuse the power cable Never use the cable for carrying, pulling or

unplugging the power tool. Keep the cable away from heat, oil, sharp

edges or moving parts. Damaged or entangled cables increase the risk of

electric shock.

4. When operating a power tool outdoors, use an extension cable suitable for

outdoor use. Use of a cable suitable for outdoor use reduces the risk of

electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in personal injury.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

2. Use personal protective equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hearing protection

and a workshop apron capable of stopping small abrasive or workpiece

fragments.

3. Avoid accidental starting. Ensure the switch is in the off position before

plugging in. Plugging in power tools that have the switch on invites

accidents.

4. Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations. Dress

properly. Do not wear loose clothing or jewellery.

6. Keep your hair, clothing and gloves away from moving parts. Loose

clothes, jewellery or long hair can be caught in moving parts. Keep the

work area clean and tidy.

7. Regularly clean the power tool’s air vents. The motor fan will draw dust

inside the housing and accumulation of material could cause electrical

hazards.

8. Avoid operator fatigue. Stop the power tool at regular intervals for a short

break to rest hands and arms.

9. Maintain your tools. Keep all handles and grips dry and clean.

ELECTRICAL SAFETY

1. Position the power cable so that it cannot be inadvertently pulled or

pinched, and where it does not cause a trip hazard.

2. This machine is designed for indoor environments and must not be used for

other purposes.

3. If the machine requires repair, always contact your Clarke dealer. Always

insist on original spare parts. Repairs carried out by unauthorized persons

may be dangerous and invalidate the guarantee.

4. This machine must only be used by adults. Children should not be allowed

to play with this appliance.

5. Do not use extension power cables.

6. Before cleaning or maintenance operations, always unplug the machine

from the power supply.

POWER TOOL USE AND CARE

1. Do not force the machine. Use the correct power tool for your application.

It will do a better and safer job at the rate for which it was designed.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the power tool from the power supply before making any

adjustments, changing accessories, or storing the tool. These measures will

reduce the risk of the power tool starting accidently.

4. Store power tools out of the reach of children and do not allow persons

unfamiliar with these instructions to operate the power tool. Power tools are

potentially dangerous in the hands of untrained users.

5. Maintain power tools in top condition. Keep tools/ machines clean for the

best and safest performance. Check for misalignment or binding of

moving parts, broken parts, or any condition that may affect the power

tool’s operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

6. Use recommended accessories. The use of improper accessories could be

hazardous.

7. Machine cleanliness. Do not allow the ventilation slots in the machine to

become blocked with dust.

8. Check the power tool for damage before using the machine. Any

damaged part should be inspected to ensure that it will operate properly

and perform its intended function. Check for alignment of moving parts,

breakage of parts, mountings, and any other condition that may affect the

machine’s operation. Any damage should be properly repaired or the part

replaced. If in doubt, DO NOT use the machine. Consult your local dealer.

SERVICING

1. When necessary, have your power tools serviced or repaired by a qualified

person using identical replacement parts. This will ensure that the safety of

the power tool is maintained.

ADDITIONAL PRECAUTIONS FOR BANDSAWS

1. Always check safety guards are closed and secure before switching the

machine on.

2. Always use a push stick and fence with small workpieces wherever

practical.

3. Always use the appropriate saw blade for the material being cut.

4. Always wear gloves for handling the saw band and rough material.

5. Never use the machine if the electric cable or plug is in poor condition.

6. Never attempt any maintenance or adjustments of the band when it is in

motion.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

7. Never touch the blade immediately after use, when changing the blade

always allow time for it to cool.

8. Never use damaged blades. (Replacement blades are available from your

Clarke dealer.

9. Replace table insert if the slot has become enlarged.

10. When cutting wood, ensure all nails or fastenings have been removed

beforehand. Nails will damage the saw blade.

11. When cutting round timber stock, use a suitable jig or fixture to keep the

work from turning.

12. Always ensure the blade is fully tightened and correctly adjusted before

use.

13. Keep the mains cable well away from the machine and ensure an

adequate electrical supply is close at hand so that the operation is not

restricted by the length of the cable.

14. Switch the machine off as soon as the task is completed.

SAFETY SYMBOLS

The following safety symbols may be found on the machine.

Wear a dust mask

Wear eye protection

Read instruction manual before use

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATION

CBS190B

Weight 16.5 kg

Dimensions (W x D x H) 456 x 404 x 710 mm

Table Size (W x D) 305 x 305 mm

Table tilt angle 0 - 45o

Mitre Gauge Range Left 60o/ Right 60o

Maximum Cutting Width@90o190 mm

Maximum Cutting Depth@45o40 mm

Maximum Cutting thickness@90o80mm

Maximum Cutting thickness@45o40mm

Height of Fence 50 mm

Rated Power 350 W

Blade Speed (no load) 14.7 m/sec

Duty Cycle S1 continuous

Sound Pressure Level (Lp) 67.5 dB(A)

Sound Power Level Measured (Lw) 80.0 dB(A)

Power Supply 230V/50Hz

Blade Type

Blade Length (welded loop) 1425 mm

Blade Width 6.35 mm

Blade Tooth Pitch 6 tpi

Blade thickness 0.3 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply via a Residual

Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit a 5 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NODESCRIPTION NODESCRIPTION

1 Blade Tension Setting Knob 7 Tilting Work Table

2 Belt Tracking Knob 8 Dust Extract Port

3 Guide Height Setting Knob 9 Rip Fence

4 Adjustable Blade Guide Assy 10 Start/Stop Buttons

5 Blade 11 Cover Securing Bolts

6 Mitre Gauge Assembly

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

ASSEMBLY

PREPARATION

• Make sure that all parts are un-damaged and are present. If any parts are

missing or damaged please contact your CLARKE dealer immediately.

• For maximum stability, the bandsaw should be bolted to either a

workbench, a suitable stand, or a piece of plywood, and the plywood

then clamped firmly to a workbench using clamps, while the bandsaw is

being used.

• The saw must be located in an area large enough to allow you to work

freely, taking into account the size of your workpiece and that there is

adequate lighting.

• Make sure that the electrical supply is close by. Take extra care if extension

leads are used. Make sure that there is no possibility of tripping over the

lead when moving around the work area.

FITTING THE TABLE

1. Fit the work table to the bandsaw

using the table locking lever

components.

2. Screw the locking knob and

washer finger tight to the frame to

secure the table.

3. Add the locking lever and its

retaining bolt to the locking knob,

tightening the retaining bolt

gently with the hex wrench.

4. Check that the table can still move when the locking lever is loosened.

5. Ensure the saw blade is central in the table insert.

Tabla de contenidos

Otros manuales de Sierra de Clarke

Clarke

Clarke Woodworker CTS10PLM Manual de instalación y operación

Clarke

Clarke CRS350M Manual de instrucciones

Clarke

Clarke Woodworker CTS10D Manual de instalación y operación

Clarke

Clarke Metalworker CBS45MD Manual de instalación y operación

Clarke

Clarke CT4014 Manual de usuario

Clarke

Clarke CMSF110 Manual de instalación y operación

Clarke

Clarke ZX-R Pro Series Manual de instrucciones

Clarke

Clarke CBS7MB Manual de instalación y operación

Clarke

Clarke Woodworker CMS10S2B Manual de instrucciones

Clarke

Clarke CSS 400 Instrucciones de funcionamiento

Clarke

Clarke STRONG ARM CFPSM Manual de instrucciones

Clarke

Clarke Woodworker CBS12WV Manual de instalación y operación

Clarke

Clarke CSS400C Manual de instrucciones

Clarke

Clarke CBS 355 Manual

Clarke

Clarke Woodworker MBS600B Manual de usuario

Clarke

Clarke CTS800C Manual de instrucciones

Clarke

Clarke WoodWorker CCS1 Manual de instalación y operación

Clarke

Clarke CAT32B Manual de instalación y operación

Clarke

Clarke woodworker CMS10 6501305 Manual de instalación y operación

Clarke

Clarke Contractor CCS2 Manual de instalación y operación

Clarke

Clarke CCS12 Manual de instalación y operación

Clarke

Clarke Woodworker CBS12WC Manual de instalación y operación

Clarke

Clarke CLS505 Manual de usuario

Clarke

Clarke CPS85 Manual de instrucciones

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario