Clarke CTC150LI Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0921

12V CORDLESS TYRE INFLATOR

MODEL NO: CTC150LI

PART NO: 7640300

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Tyre Inflator. The CTC150Li can be used

for inflating car, motorcycle and bicycle tyres, inflatable sports balls and other

inflatables. The compressor is not waterproof and should not be used in any

wet applications.

Before attempting to use the product it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will ensure

the safety of yourself and that of others around you and you can also look

forward to the product giving you long and satisfactory service.

Model CTC150Li

Part No 7640300

Tyre Inflator

Hose length 300mm

Max working pressure 10.3 Bar/150 psi

Max flow rate 22L/min

Ingress protection IPX0 (non-waterproof)

Duty cycle 10 mins on/10 mins off

Dimensions (L x W x H) 315 x 78 x 265 mm

Weight 1.3 kg

12V Power supply

Extending cable length 2.8 M

Plug type In-car 12V plug-in adaptor

Battery Pack

Battery Type Lithium Ion

Battery capacity 12V / 2000mAh

Input 15V-0.5A

USB Output 5V-1A

Charging time Approx 60 minutes

Power Adaptor for Battery Pack

Cable Length 1m

Input AC 230V~50Hz

Output DC 15V-0.5A

Insulation Class II

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

SAFETY SYMBOLS

The following safety symbols are shown on the product and/or it’s packaging.

Please read all of the safety and operating instructions carefully before use..

GENERAL SAFETY WARNINGS

PERSONAL SAFETY

1. ALWAYS stay alert, watch what you are doing and use common sense

when operating the tyre inflator. DO NOT use while you are tired or under

the influence of medication, drugs or alcohol. A moment of inattention

can result in personal injury.

2. ALWAYS protect yourself against electric shock. Never operate the tyre

inflator in wet or damp locations.

3. NEVER over-reach. Keep your proper footing and balance at all times to

enable better control of the tyre inflator in unexpected situations.

4. NEVER attempt any complex repairs yourself. If you have a technical

problem contact your local CLARKE dealer.

Read this instruction

booklet carefully before

use

Lithium-Ion battery

supplied to be re-cycled

in accordance with

regulations.

Class II appliance without

earth connection.

Positive tip plug-in

connector

Caution-hot surfaces Danger;- potentially

explosive battery

material.

Do not immerse battery in

water.

WARNING: WHEN USING ELECTRICAL TOOLS, BASIC SAFETY

PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK AND PERSONAL INJURY.

WARNING: READ ALL THESE INSTRUCTIONS BEFORE ATTEMPTING TO USE

THIS PRODUCT AND KEEP THESE INSTRUCTIONS IN A SAFE PLACE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. ALWAYS store the tyre inflator out of reach of children.

6. Keep the work area clean and well lit. Floors should always be kept clear.

Cluttered or dark areas invite accidents.

7. DO NOT work in enclosed areas or near naked flames.

GENERAL PRODUCT USE AND CARE

1. ALWAYS thoroughly familiarise yourself with this product and its operation

and always read the instructions in this manual before using the product.

2. NEVER use this tyre inflator if any part is damaged. If so, have it inspected

and repaired by your CLARKE dealer.

3. NEVER attempt to modify the fittings or attachments in any way. Doing so

will invalidate the guarantee and could result in personal injury.

4. NEVER abuse the charging cable. NEVER pull on the cable when removing

the plug from the socket or lift the tyre inflator by the power cable.

5. NEVER USE A TYRE INFLATOR WHICH APPEARS DEFECTIVE OR IS OPERATING

ABNORMALLY: If the tyre inflator operates unusually or makes strange

noises, switch off immediately. Arrange repairs with your CLARKE dealer.

6. BEFORE USE CHECK THE TYRE INFLATOR AND HOSE FOR DAMAGE: NEVER use

the tyre inflator if it is damaged. Have it repaired by your CLARKE dealer.

DO NOT use if the On/Off switch does not operate correctly.

7. Keep the motor air vents clear and free from dust.

8. Take care when using this tyre inflator to inflate small, low-pressure objects

such as children's toys or footballs can explode if over-inflated.

9. ALWAYS use in a safe area away from traffic and other hazards.

10. ALWAYS ensure that tyre pressure checks are carried out to the tyre and

vehicle manufacturer’s recommended pressures.

11. NEVER overstretch the power lead or high pressure hose.

ENVIRONMENTAL RECYCLING POLICY

By purchasing this product, the customer is taking on the obligation

to comply with current WEEE regulations.

This means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws

governing Waste Electrical and Electronic Equipment (WEEE) at a recognised

disposal facility.

This product contains valuable raw materials. Metal products should be taken

to your local civic amenity site for recycling of metal products.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

OVERVIEW

UNPACKING

After removing the tyre inflator from its packaging, check that it has not been

damaged in transit. Report any damage immediately to the CLARKE dealer

where the item was purchased.

ADAPTORS

Clipped to the top of the tyre inflator or are three adaptors for different uses.

These are provided to inflate sports balls, air beds, small inflatables and bicycle

tyres etc. To avoid over-inflation, always follow manufacturer’s instructions for

the item to be inflated.

• Toy/air bed adaptor

• Sports ball adaptor

• ‘Presta’ bicycle tyre valve adaptor

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

WORKING CONDITIONS

1. DO NOT use the tyre inflator in a damp or wet environment. The compressor

should only be used with good ventilation. There should be no dust, acids,

vapour, explosive or flammable gases in the room.

2. DO NOT cover the tyre inflator. Always position it with good all-round air

ventilation and that the air intake air is dry and dust free.

POWERING THE TYRE INFLATOR

NOTE: 230V mains + USB charges the battery,

Car charger charges the 12V power pack

USING THE BATTERY

Charge the battery using the 230V

mains power supply adaptor cable.

Connect one end to the battery

pack and the other end to any mains

power socket. The 3 x LED bars will all

be illuminated when the battery is

fully charged.

Fit the power pack to the base of the

tyre inflator by sliding it forward until it

clips into place.

NOTE: The base of the power pack can only slide one way.

USING A USB CABLE

Charge the battery using a USB cable (not supplied) via the USB port.

USING THE CAR CHARGER VIA THE POWER PACK

Power the tyre inflator directly from

the vehicle 12V power pack using the

car adaptor.

Fit the adaptor to the base of the tyre

inflator by sliding it forward until it

clips into place.

NOTE: The vehicle adaptor can

only slide one way.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

USING THE TYRE INFLATOR

1. Always inspect the tyre inflator before use to ensure the high pressure hose

is in good condition.

2. Connect the air hose to the tyre

inflator by screwing the hose into

the end of the tyre inflator.

3. Connect the other end of the air

hose to the valve stem of the item

you are inflating.

• An adaptor is supplied for inflating

sport balls including soccer,

basketballs and footballs.

NOTE: When inflating items of 10

PSI or less, inflate in short bursts and check after each burst by

feel or with a calibrated measuring device to determine

accurate pressure. Pressure required for most sports balls is too low

for accurate reading on tool gauge.

4. Connect power to the tyre inflator using options on page 6.

• The manufacturer set pressure is 35 PSI and this tyre inflator has memory

function. The gauge will indicate units and value.

5. Press "SET" button to choose the

desired unit (PSI,BAR,KPA,kg/cm2).

6. Press "-" or "+" button to choose

the desired value. Press and hold

"-” or "+" button will accelerate

numerical change. After the

screen flashes three times, the

screen will show "0" and the

system will enter the chosen unit.

7. Press the On/Off trigger to start

and hold for continuous working.

• The built-in LED light is on during

inflation.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• For continuous inflation you can

push the switch lock upwards to

lock while the On/Off trigger is

depressed. In this way, inflation

continues without pressing any

button. To stop, simply squeeze

the trigger to release the locking

switch.

NOTE: Note that the tyre inflator has

a 10 minute running/10

minutes resting duty cycle.

• When the desired pressure is reached, the tyre inflator will stop working

as it has pre-set function. when the desired the pressure is reached,

the reading may have a +/- 1.5PSI difference. (This is normal)

8. After use, loosen the hose and remove from the tyre inflator.

• When not in use, adaptors provided with the compressor can be clipped

to the storage area on the top of the compressor.

TYRE INFLATION

1. Fix the tyre valve connector onto

the vehicle tyre valve, ensuring

the valve is clean.

• When connected correctly, the

digital display will show the

current pressure in the tyre. If this is

the correct tyre pressure as stated

in your vehicle handbook, remove

the valve connector.

2. If the tyre is below the

recommended pressure (as specified in your vehicle handbook), press

either the ‘-’ or ‘+’ pre-set button to adjust the pre-set value on the display

to the correct tyre pressure.

WARNING: THE HOSE WILL BE HOT AFTER USE. REMOVE CAREFULLY.

WARNING: IMPROPERLY ATTACHED HOSES OR ACCESSORIES CAN

BECOME DETACHED UNDER PRESSURE AND CAUSE SERIOUS INJURY.

POSSIBLE AIR LEAKS CAN CAUSE FAULTY PRESSURE READINGS. MAKE

SURE ALL CONNECTIONS ARE TIGHTLY SECURED.

WARNING: THE GAUGE IS ONLY TO BE USED AS A REFERENCE, ALWAYS

CARRY OUT A FINAL CHECK OF THE TYRE PRESSURE WITH A GAUGE

CONFORMING TO BS EN 12645.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

NOTE: The unit will default to the last tyre pressure set. You can then

adjust this using the ‘-’ or ‘+’ buttons.

3. Press the Power Switch to 'ON'.

4. The tyre inflator will now inflate your tyre to the pre-set pressure and switch

off automatically when the pressure is reached. Towards final inflation, the

tyre pressure display reading will be slightly higher than the selected

pressure. When the tyre inflator stops, the final reading will be the selected

pressure. This is a normal function of the unit.

5. Switch OFF the tyre inflator and remove the tyre valve connector from the

tyre valve, returning the hose to its storage position.

IMPORTANT: The ‘-’ or ‘+’ buttons should never be pressed while the tyre

inflator is running.

If you leave the tyre inflator connected to the 12V supply but do not inflate the

tyre, after a few minutes the Digital Display will switch off. To turn back on,

press the Pressure Format Select Button.

• When inflating tyres with normal “Schrader” valves, no adaptors need to

be fitted to the hose.

• Presta valves require the adaptor to be screwed onto the valve before

attaching the hose.

6. Avoid inflating the objects above the recommended inflation pressure. This

could lead to damage and /or injuries.

MAINTENANCE

Keep the tyre inflator free of dirt and dust as far as possible. Wipe with a clean

cloth or blow it down with compressed air at low pressure. Do not use cleaning

agents or solvents as these may be aggressive to the plastic parts. Ensure that

no water can get into the interior of the tyre inflator

Your CLARKE tyre inflator has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet carefully,

you encounter problems, take the tyre inflator to your local CLARKE dealer.

The car adaptor incorporates a 15A fuse which can be replaced by

unscrewing the end of the plug.

Store the tyre inflator in a dry location.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase. This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for the purpose for which it

was intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

No Description No Description

1 Flexible hose attachment 9 Motor/pump assembly

2 Trigger 10 Nozzle attachment

3 Trigger Lock switch 11 Screw

4 Locating base 12 Display housing

5 12V Adaptor 13 Pressure selector PCB

6 Hair spring 14 Digital display

7 Coil spring 15 Battery Pack

8Operatingswitch

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke ECSS-1 Guía del usuario

Clarke

Clarke CMPS2 Manual de instrucciones

Clarke

Clarke CIR450 Manual de instalación y operación

Clarke

Clarke STRONG-ARM CSA10BB Manual de instrucciones

Clarke

Clarke CPSB100 Manual de instrucciones

Clarke

Clarke CONTRACTOR CON800 Manual de instalación y operación

Clarke

Clarke CDP10B Manual de instrucciones

Clarke

Clarke CHG 1500B Manual de instalación y operación

Clarke

Clarke CAT209 Manual de instalación y operación

Clarke

Clarke CEW1000 Manual

Clarke

Clarke X-PRO CAT140 Manual de instalación y operación

Clarke

Clarke CAT21B Manual de instalación y operación

Clarke

Clarke CSG1C Manual de instrucciones

Clarke

Clarke CSB34 Manual de instrucciones

Clarke

Clarke CAT22B Manual de instalación y operación

Clarke

Clarke CWS200 Manual de instrucciones

Clarke

Clarke 6505512 Manual de instrucciones

Clarke

Clarke Air CAT149 Manual de instalación y operación

Clarke

Clarke CHT141 Manual de usuario

Clarke

Clarke CBTSR Manual de instrucciones

Clarke

Clarke Air 25C Manual de instalación y operación

Clarke

Clarke CWS250 Manual de instalación y operación

Clarke

Clarke Air CAT105 Manual de instrucciones

Clarke

Clarke CAT51 Manual de instalación y operación

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual