Clarke COEBS1 Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0416

OSCILLATING BELT/BOBBIN SANDER

MODEL NO: COEBS1

PART NO: 6500460

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. Keep work area clear

• Cluttered areas and benches

invite injuries.

2. Consider work area environment

• Do not expose tools to rain.

• Do not use tools in damp or wet

locations.

• Keep work area well lit.

• Do not use tools in the presence

of flammable liquids or gases.

3. Guard against electric shock

• Avoid body contact with earthed

or grounded surfaces (e.g. pipes,

radiators, ranges, refrigerators).

4. Keep other persons away

• Do not let persons, especially

children, not involved in the work

touch the tool or the extension

cord and keep them away from

the work area.

5. Store idle tools

• When not in use, tools should be

stored in a dry locked-up place,

out of reach of children.

6. Use protective equipment

• Use safety glasses.

• Use face or dust mask if working

operations create dust.

WARNING: READ ALL

INSTRUCTIONS. FAILURE TO

FOLLOW ALL INSTRUCTIONS

LISTED BELOW MAY RESULT IN

ELECTRIC SHOCK, FIRE AND/OR

SERIOUS INJURY.

7. Do not force the tool

• It will do the job better and safer

at the rate for which it was

intended.

8. Use the right tool

• Do not force small tools to do the

job of a heavy duty tool.

• Do not use tools for purposes not

intended; for example do not use

circular saws to cut tree limbs or

logs.

9. Dress properly

• Do not wear loose clothing or

jewellery, they can be caught in

moving parts.

• Non-skid footwear is

recommended when working

outdoors.

• Wear protective hair covering to

contain long hair.

10. Dust extraction equipment

• Ensure dust extraction equipment

is used.

11. Do not abuse the cord

• Never yank the cord to

disconnect it from the socket.

Keep the cord away from heat,

oil and sharp edges.

12. Secure the work

• Where possible use clamps or a

vice to hold the work. It is safer

than using your hand.

13. Do not overreach

• Keep proper footing and

balance at all times.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

14. Maintain tools with care

•.

• Inspect tool cords periodically

and if damaged have them

repaired by an authorized

service facility.

• Inspect extension cords

periodically and replace if

damaged.

• Keep handles dry, clean and

free from oil and grease.

15. Disconnect tools

• When not in use, before servicing

and when changing accessories

such as blades, bits and cutters,

disconnect tools from the power

supply.

16. Remove adjusting keys and

wrenches

• Form the habit of checking to

see that keys and adjusting

wrenches are removed from the

tool before turning it on.

17. Avoid unintentional starting

• Ensure switch is in “off' position

when plugging in.

18. Use outdoor extension leads

• When the tool is used outdoors,

use only extension cords

intended for outdoor use and so

marked.

19. Stay alert

• Watch what you are doing, use

common sense and do not

operate the tool when you are

tired.

20. Check damaged parts

• Before further use of tool, it

should be carefully checked to

determine that it will operate

properly and perform its

intended function.

• Check for alignment of moving

parts, binding of moving parts,

breakage of parts, mounting

and any other conditions that

may affect its operation.

• A guard or other part that is

damaged should be properly

repaired or replaced by an

authorized service centre unless

otherwise indicated in this

instruction manual.

• Have defective switches

replaced by an authorized

service centre.

• Do not use the tool if the switch

does not turn it on and off.

21. Warning

• The use of any accessory or

attachment other than those

recommended in this instruction

manual may present a risk of

personal injury.

22. Have your tool repaired by a

qualified person

• This electric tool complies with

the relevant safety rules. Repairs

should only be carried out by

qualified persons using original

spare parts, otherwise this may

result in considerable danger to

the user.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SANDER SPECIFIC RULES

• FIRMLY CLAMP OR BOLT your

sander to a workbench or table

at approximately hip height.

• NEVER stand or have any part of

your body in line with the path of

the workpiece.

• PLAN YOUR WORK TO REDUCE

THE RISK OF THROWBACKS (when

the workpiece catches the

sanding drum and is torn from

your hands).

• MAKE SURE THERE IS NO DEBRIS

between the workpiece and its

supports.

• WHEN SANDING IRREGULARLY

SHAPED WORKPIECES, plan your

work support so it will not slip and

be pulled from your hands.

• USE EXTRA CAUTION WITH LARGE,

very small or awkward

workpieces.

• NEVER USE THIS SANDER to finish

pieces too small to hold by hand.

• USE EXTRA SUPPORTS (TABLES,

SAW HORSES, BLOCKS, ETC.) for

any workpieces large enough to

tip when not secured to the work

surface.

•NEVERsandmorethanone

piece at a time. DO NOT STACK

more than one workpiece on the

sander table at a time.

• ALWAYS FEED WORKPIECE FROM

LEFT TO RIGHT against the

direction the drum sleeve is

rotating.

• DO NOT USE DRUMS, sanding

sleeves or belts which show visual

signs of wear such as grooves,

tears or rips.

• ALWAY S STAY A L E R T! D o n o t a ll o w

familiarity (gained from frequent

use of your sander) to cause a

careless mistake. ALWAYS

REMEMBER that a careless

fraction of a second is sufficient

to inflict severe injury.

• MAKE SURE THE WORK AREA HAS

AMPLE LIGHTING to see the work

and that no obstructions will

interfere with safe operation

BEFORE performing any work

using your sander.

• ALWAYS TURN OFF THE SANDER

before disconnecting it to avoid

accidental starting when

reconnecting to power supply.

• NEVER leave the sander

unattended while connected to

a power source.

• SUPPORT WORKPIECE with mitre

gauge, work rest, or worktable.

• SAVE THESE INSTRUCTIONS. Refer

to them frequently and use them

to instruct others who may use

this sander. If you loan someone

this sander, loan them these

instructions also.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SANDING DUST SAFETY WARNINGS

Some dust created by sanding, and other construction activities contains

chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

•leadfromlead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such as those dust masks that

are specially designed to filter out microscopic particles.

SAFETY SYMBOLS

Read this instruction

booklet carefully.

Wear ear protection.

Wear eye

protection.

Wear a dust mask that is

specially designed to

filter microscopic

particles.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug.

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING

CURRENT OF LESS THAN 30mA MUST BE USED.

If you are not sure, consult a qualified electrician. DO NOT try to do any repairs

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

a 5 Amp

the cable is firmly held by the clamp

fuse.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONTENTS

The following items should be supplied in the carton. If any parts are missing,

do not operate until the missing parts are replaced. Failure to follow this

instruction could result in serious injury.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

SECURING THE SANDER TO A WORKBENCH

If sander is to be used in a permanent location, it should be fastened securely

to a workbench via the four securing holes (one on each corner).

1. Mark out the position of the holes.

2. Secure using suitable bolts, washers, and nuts (not supplied).

An alternative method is to fasten the sander to a mounting board.

The board should be sufficient size to avoid tipping while in use. Any good

grade of 3/4" plywood or chipboard will be sufficient.

The mounting board can then be clamped to a workbench when required.

DUST EXTRACTION

1. Connect a suitable dust collector

to the dust extraction port.

• The dust exhaust port has an

internal diameter of 36 mm and

an outside diameter of 39 mm.

NOTE: Even with a dust collection

system, it is necessary to

periodically clean sanding

dust from the recess in the

table. A build up of dust in the

table recess may prevent the belt or spindle from making a complete

oscillation.

WARNING: CONTACT WITH, OR INHALATION OF DUST FROM LEAD BASED

PAINTS CAN ENDANGER THE HEALTH OF THE OPERATOR AND

BYSTANDERS. ALWAYS WEAR A SUITABLE DUST MASK WHEN USING THE

SANDER.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

EDGE SANDING SETUP

INSTALL THE SANDING BELT ASSEMBLY

1. If fitted, remove the fan and table

insert from the sander.

• Clear the recess of any debris.

2. Slide the fan onto the motor shaft

(vanes face down).

• You may need to rotate the fan

to get it to locate properly,

(when correctly fitted the fan

rotates with the spindle).

• The fan must be used at all times.

3. Slide sanding belt assembly over

the spindle as shown.

4. Fit the washer and hand nut.

• Do not overtighten the hand

nut.

5. Install the sanding belt (See

“Removing/installing the Sanding

Belt” on page 11.

6. Place the backstop into position

and secure in place with the

backstop securing bolt.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke CPR2 Manual de instalación y operación

Clarke

Clarke CAT113 Guía de instalación

Clarke

Clarke Air CAT149 Manual de instalación y operación

Clarke

Clarke CIR18LiC Manual de instalación y operación

Clarke

Clarke Contractor CON15 Manual de instalación y operación

Clarke

Clarke CTILG 5060287 Instrucciones de instalación

Clarke

Clarke ECSS2 Manual de instrucciones

Clarke

Clarke Strong-arm AHP 16 Manual de instrucciones

Clarke

Clarke CAT22B Manual de instalación y operación

Clarke

Clarke Metalworker CDP301B Manual de instalación y operación

Clarke

Clarke METALWORKER CBS20 Manual de usuario

Clarke

Clarke 6505512 Manual de instrucciones

Clarke

Clarke CHT 459 Manual de usuario

Clarke

Clarke CAT51 Manual de instalación y operación

Clarke

Clarke CPT1000 Manual de instrucciones

Clarke

Clarke CIR450C Manual de instalación y operación

Clarke

Clarke CHG1600 Manual de usuario

Clarke

Clarke Air CAT217 Manual de instalación y operación

Clarke

Clarke CHT674 Manual de usuario

Clarke

Clarke CTC150 Manual de instrucciones

Clarke

Clarke CAT55 Manual de instalación y operación

Clarke

Clarke STRONG-ARM CSA4B Manual de instrucciones

Clarke

Clarke Strong-Arm CSA15F Manual de instalación y operación

Clarke

Clarke CAG120 Manual de instalación y operación

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual