Clarke Air CAT63 Manual de instalación y operación

OPERATING & MAINTENANCE

INSTRUCTIONS

GC0314

AIR NIBBLER

MODEL NO: CAT63

PART NO: 3110463

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Nibbler.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Do not overreach - Keep proper footing and balance at all times.

4. Never use oxygen, CO2, combustible gasses, or any bottled gas, as a

source of power for the grease gun. This product should only be used with

a suitably rated compressed air supply.

5. Do not connect the air supply hose with your finger on the trigger of the

gun.

6. Do not fit the tool to any stand or clamping device that may damage it.

7. Do not exceed the maximum pressure for the tool of 90 psi / 6.2 bar.

8. Keep the air supply hose away from heat, oil and sharp edges.

9. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

10. Do not use the tool for any other purpose than described in this manual.

11. Do not carry out any alterations or modifications to the tool.

12. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Moving to another work area.

• Passing the tool to another person.

• Never use the tool if it is defective or operating abnormally.

13. This tool should be serviced at regular intervals by qualified service

personnel.

14. Avoid damaging the tool for example by applying excessive force of any

kind.

15. Always maintain the tool with care. Keep it clean for the best and safest

performance.

16. Do not force or misuse the tool. It will do a better and safer job at the rate

for which it was designed.

HAZARDS SPECIFIC TO CUTTING TOOLS

1. Be careful around all moving parts and pinch points. Always keep your

fingers away from the point of cutting.

2. Ensure material is properly supported during cutting. Use supports for long

material. Hold the material securely to prevent it tilting during the cut. Use

clamps or vices to hold the work piece whenever possible.

3. Take care of sharp edges produced by the cutting operation.

4. Do not use damaged punches. When replacing cutting tool parts make

sure they are correctly and securely mounted.

5. Anticipate the unexpected tool movement due to a binding punch.

Release the trigger immediately if this occurs.

TRANSPORTATION

1. Never carry an air tool by the air supply hose.

2. Never carry an air tool with your finger on the trigger.

STORAGE

1. When not in use, the tool must be disconnected from the air supply and

stored in a dry place out of the reach of children (preferably in a locked

cabinet).

2. Avoid storing in cold environments.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

The CAT63 Air Nibbler is ideal for fast, accurate sheet metal cutting of curved

or intricate shapes using its 4-way adjustable punch head. The punch and die

can be rotated through 360oto aid access and obtain maximum consumable

life.

NO DESCRIPTION NO DESCRIPTION

1 Punch 3 Trigger

2 Die 4 Air Inlet

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked & topped up with oil. Clarke air-line oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi

at the tool when running. Higher pressures and unclean air will

shorten the life of the tool due to faster wear and is a possible safety

hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

NOTE: Ensure the compressor is turned off.

1. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of the air tool.

2. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the inlet connector or via the hose

at the nearest connection to the air supply.

3. Connect a suitable hose as shown.

4. Connect the other end of the hose

to the compressor.

5. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be helpful for

sealing threaded connections.

6. Your air tool is now ready for use.

You can fit a whip hose with a quick fit coupling if required (available from

your Clarke dealer).

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

In order to improve access to the workpiece, the die can be rotated through

360o.

1. To do this, loosen the locknut with

a 22mm spanner and rotate the

die on the punch until it is in the

right position for the job in hand.

2. Hold the die steady with a 15mm

spanner on its flats and retighten

the locknut.

3. Ensure you workpiece is properly

secured and marked out.

4. Connect the nibbler to the airline.

5. Start the nibbler by squeezing the throttle lever.

6. Introduce the sheet metal into the slot in the end of the die. Apply only light

pressure to move the tool in the desired direction through the material.

7. Do not allow the nibbler to run freely for long periods of time as this could

harm the bearings.

NOTE: It is recommended that a whip hose with a swivel (not included)

be used to prevent twisting, kinking and resultant wear to the air

hose.

DISCONNECTING THE AIR SUPPLY

Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

1. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

2. Once the pressure has been released, disconnect the air supply hose from

the air tool.

3. Store the tool safely in its box in a dry, secure environment.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

DAILY

1. Before use, drain water from the air-line and compressor.

2. This air tool should be lubricated before use. Turn the tool upside down and

pour 1-2 drops of Clarke air-line oil into the air inlet. This should be carried

out regardless of whether or not an in-line mini oiler is used. If an in-line mini

oiler is not used, this procedure should be repeated after every two hours

of constant use.

CLEANING

1. Keep the tool clean.

2. Deposits in the tool may also reduce efficiency. This can be corrected by

cleaning the air inlet and flushing out the tool with gum solvent oil, or failing

this, the tool should be disassembled, thoroughly cleaned, dried and

reassembled.

3. If the tool becomes inefficient and the air supply is of good quality, it may

be necessary to replace worn or damaged parts. You may prefer to take

the tool to your Clarke dealer if internal maintenance is required.

Your Clarke air tool has been designed to give long and trouble free service. If,

however, having followed the instructions in this booklet carefully, you

encounter problems, take the unit to your local Clarke dealer.

PERFORMANCE

Please note that factors other than the tool may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

**Clarke Air-lne Oil (part no. 3050825) is available from your Clarke dealer.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CHANGING THE PUNCH AND DIE

1. Loosen the locknut using a 22mm

spanner and unscrew the die (with

the locknut on it) from the body of

the tool.

2. Place a 9mm spanner onto the

hex section of the die collar as

shown and undo/remove the die

collar and punch.

3. Remove the old punch from the

collar and insert the new one.

4. Screw the collar and punch back

into place and tighten with the

spanner.

5. Slide the die and locknut over the

punch and screw it back into the nibbler until the bottom of the punch is

flush with the bottom of the die. Rotate the die into the best position

required by the workpiece. Hold the die steady with a 15mm spanner on its

flats and re-tighten the locknut.

STORAGE

If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of

Clarke air-line oil into the air inlet, and depress the trigger in order to lubricate

the internal parts.

When not in use, disconnect from air supply, clean and store in a safe, dry

place.

ACCESSORIES

A wide range of airline accessories is available including filter/regulators,

lubricators, high-pressure hoses (5 to 50 metres) etc.

Contact your Clarke dealer or Clarke International Service Department for

further information.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke CWS200B Manual de usuario

Clarke

Clarke CAT50 Manual de instalación y operación

Clarke

Clarke Metalworker CDP501F Manual de instalación y operación

Clarke

Clarke CTIDG2 Manual de instrucciones

Clarke

Clarke Strong-Arm AP500B Manual de usuario

Clarke

Clarke METALWORKER CDP401B Manual de instalación y operación

Clarke

Clarke CJS380 Manual de instalación y operación

Clarke

Clarke CAT141 Manual de instalación y operación

Clarke

Clarke CAT51 Manual de instalación y operación

Clarke

Clarke X-PRO CAT140 Manual de instalación y operación

Clarke

Clarke CAT21B Manual de instalación y operación

Clarke

Clarke CHG1500D Manual de usuario

Clarke

Clarke CPT1000 Manual de instrucciones

Clarke

Clarke Strong-Arm CSA15F Manual de instalación y operación

Clarke

Clarke CIR18LiC Manual de instalación y operación

Clarke

Clarke cp185 Manual de instalación y operación

Clarke

Clarke Woodworker CJS1-C Manual de instalación y operación

Clarke

Clarke Metalworker CDP101B Manual de instalación y operación

Clarke

Clarke STRONG-ARM CSA12F Manual de instrucciones

Clarke

Clarke CAT171 Manual de usuario

Clarke

Clarke ECSS-1 Guía del usuario

Clarke

Clarke CIR18Li Manual de instalación y operación

Clarke

Clarke Strong-Arm AHP 26 Manual de instrucciones

Clarke

Clarke CPS125 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual