Clarke CPP5 Manual de instalación y operación

AIR PRESSURISED PAINT FEED

CONTAINER

OPERATING & MAINTENANCE

INSTRUCTIONS

Model Nos:

CPP5 • CPP11 • CPP30 • CPP40

AIR PRESSURISED PAINT FEED

CONTAINER

1106

CLARKE GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period

of 12 months from the date of purchase. Please keep your receipt as proof

of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product

can be returned to us without prior permission.

This guarantee does not affect your statutory rights.

Please read these instructions carefully before using the Paint Pot

Thank you for purchasing this CLARKE Air Pressurised Paint Feed Container.

Before using the device, please read this manual thoroughly and carefully

follow all instructions given. This is for your own safety and that of others around

you, and is also to help you achieve long and trouble free service from your

new product.

SPECIFICATIONS

CPP5 CPP12 CPP30 CPP40

Inner Container capacity 3.25L 9.25L 24.5L 34L

Outer Container capacity 4.2L 11.7L 31.2L 43.4L

Fluid Type Oil/Solvent based paints

Maximum Operating Pressure 3bar 3bar 3bar 3bar

Absolute Maximum Pressure 5.5bar 5.5bar 5.5bar 5.5bar

Air Hose Connection 1/4”BSP 1/4”BSP 1/4”BSP 1/4”BSP

Liquid Hose Connection 3/8” BSP 3/8” BSP 3/8” BSP 3/8” BSP

Weight unpacked 5.85kg 14.5kg 24kg 26kg

SAFETY PRECAUTIONS

1. ALWAYS keep the unit perfectly clean. This will not only prolong its life, but will

also ensure you get the best results.

2. NEVER exceed an air pressure supply of 3bar (43.5psi) to the product.

3. NEVER attempt to adjust the safety valve

4. NEVER tamper with the product or modify in any way, as this could prove to

be dangerous and will invalidate the guarantee.

5. ONLY use the product for the purpose for which it is intended,

6. ALWAYS wear approved impact resistant SAFETY GOGGLES. (Eye glasses are

NOT safety glasses), and a FACE MASK

7. DO NOT remove any labels. Damaged labels should be replaced.

AIR SUPPLY

WARNING

Compressed air can be dangerous.

Ensure that you are thoroughly

familiar with all precautions relating

to the use of compressors and

compressed air supply.

Air pressure supply to the container should not be greater than 80psi. Higher pressure and

unclean air, will shorten the tools’ life because of faster wear, and could be a safety hazard.

Water in the air line will also cause damage. Ensure it is properly maintained at all times.

The recommended procedure to connect this product to an air supply, is shown below. A

filter/regulator should always be placed in line with the supply and the paint pot.

The air inlet used for connecting air supply, has a standard ¼” BSP thread.

Line pressure, or hose inside diameter, should be increased to compensate for unusually

long air hoses (over 10m). Minimum hose diameter should be 6mm (¼") ID., and fittings

should have the same inside dimensions.

FEATURES

This Paint Feed Container is designed primarily for use in spraying oil and solvent

based paint.

Clarke International provides a range of Spray Guns which may be used with

these Feed Containers. Please see your local dealer for the HVLP and PRO Ranges.

Fig.1

Fig.2 Fig.3

The illustration above is of a CPP30, but components of other models are similar.

METHOD OF OPERATION

WARNING!

ALWAYS check to ensure the container is NOT under pressure, by checking the

pressure gauge and opening the air exhaust valve - turn the knurled ring nut

anticlockwise. Tighten the ring nut once again once all air is exhausted.

1. Fill the container with paint as follows:

• Undo each lid securing wing nut and swing the bolts out of the way.

• Lift off the lid.

• Fill the inner container with paint.

NOTE: It is permissible to fill the container itself, but we strongly recommend the

inner container be used at all times, as it is easier to clean.

• Replace the lid, ensuring the wing nuts are tightened progressively.

NOTE: Models CPP 30 and CPP40 are provided with filler plugs in the lid. These may

be used if preferred, but take care to comply with all precautions before undoing

2. Connect the air supply hose to the air inlet.

NOTE: See notes on Air Supply on page 4.

3. Connect the air hose from the spray gun, to the air outlet.

4. Connect the paint hose from the spray gun to the paint outlet.

5. Ensure the pressure regulator knob is turned fully anticlockwise, then turn ON

the air supply from compressor/air supply to the paint pot.

Where necessary, turn ON the air inlet cock at the cylinder, followed by the

pressure regulator cock.

6. Turn the pressure regulator knob slowly clockwise to pressurise the container.

Working pressure will depend upon the consistency of the medium, but must

NEVER exceed 3bar. If the medium is sluggish at this pressure, then it is of too

thick consistancy, and should not be sprayed.

7. Turn ON the air outlet cock.

8. Turn ON the paint outlet cock. Fig.4

9. Finally, make adjustment

to the spray pattern

according to the spray

gun manufacturers

instructions.

The paint should be agitated

at regular intervals during use

to ensure consistancy and

avoid colour difference due

to the paint settling.The CPP5

may be shaken gently.

Prior to use, ensure the casters are properly screwed to their housings where appropriate

A typical configuration is shown in Fig.4.

MAINTENANCE

It is important to clean the complete unit thoroughly at the end of any operation.

1. Turn OFF air to the container.

2. Turn the air exhaust valve knurled ring nut anticlockwise and allow the

container to completely depressurise.

3. Loosen all lid wing nut securing nuts, swing back the bolts and move the lid so

that it rests at one side of the container.

4. Hold the spray gun and hose above the level of the unit and pull the spray

gun trigger to allow paint in the hose to drain back into the container. The

paint cock should be open (where fitted).

5. Empty the container of paint, then clean it thoroughly with solvent or white

spirits etc., depending upon the type of paint being sprayed.

Clean and dry all components that have come into contact with paint -

agitator etc.

6. With the container and other components cleaned thoroughly, pour clean

solvent or other cleaner, into the container.

7. Replace the lid and tighten the wing nuts - progressively.

8. Turn ON the air to the container and pull the spray gun trigger. Keep it pressed

until only clean solvent or other cleaner is ejected from the spray gun.

9. Repeat steps 1 - 4 to allow solvent or other cleaner to drain back into the

container.

10 Finally empty the container and dry all components thoroughly,

Store in a clean dry place, with all cocks closed, and the lid loose.

Periodically, pressurise the container to 5.5bar in order to test the safety valve.

If it does not blow off at this pressure, do not use the appliance...have the Pressure

Relief Valve replaced.

For Spare Parts and Service, please contact your nearest dealer,

or CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

PARTS & SERVICE CONTACTS

1 Container 1 KLCPP501

1a Inner Container 1 KLCPP501a

2 Lid Assy. 1 KLCPP502

3 Handle 1 KLCPP503

4 Gasket 1 KLCPP504

5 Fluid Tube 1 KLCPP505

6 Swing Bolt 1 KLCPP506

7 Washer 4 KLCPP507

8 Wing Nut 4 KLCPP508

9 Pressure Regulator 4 KLCPP509

10 Pressure Gauge 1 KLCPP510

11 Adapter - Air Inlet 1 KLCPP511

12 Fluid Outlet 2 KLCPP512

13 Fluid Outlet Adapter 1 KLCPP513

14 Air Exhaust Valve 1 KLCPP514

15 O-Ring 1 KLCPP515

16 Adapter 1 KLCPP516

22 Pressure Relief Vlv 1 KLCPP522

23 Air Flow Guide 1 KLCPP523

24 Nut 1 KLCPP524

25 Cotter Pin 4 KLCPP525

26 Snap Ring 8 KLCPP526

27 Adapter Post 1 KLCPP527

No. Description Part No: No. Description Part No:

Parts List & Diagram - CPP 5

Parts Diagram - CPP 11

1 Container 1 KLCPP1101

1a Inner Container 1 KLCPP1101a

2 Lid Assy 1 KLCPP1102

3 Gasket 1 KLCPP1103

4 Bolt 1 KLCPP1104

5 Handle 1 KLCPP1105

6 Nut Hex 1 KLCPP1106

7 Hand Lever 1 KLCPP1107

8 Bolt 1 KLCPP1108

9 Connecting Ring 2 KLCPP1109

10 O-Ring 2 KLCPP1110

11 Guide Bush 1 KLCPP1111

12 Seal Ring 1 KLCPP1112

13 Screw bolt 2 KLCPP11013

14 Guard 1 KLCPP1114

15 Hexagon nut 2 KLCPP1115

16 Adapter 1 KLCPP1116

17 Fluid Outlet adapter 1 KLCPP1117

18 Air Inlet Adapter 2 KLCPP1118

18a Adapter 1 KLCPP1118a

19 Air Cock 1 KLCPP1119

20 Pressure Regulator 1 KLCPP1120

21 Tee Piece 1 KLCPP1121

22 Pressure gauge 1 KLCPP1122

29 Pressure Relief Valve 1 KLCPP1129

30 Adapter 1 KLCPP1130

31 O-ring 1 KLCPP1131

32 Air Exhaust Valve 1 KLCPP1132

33 Agitating rod 1 KLCPP1133

34 Hex. Nut 1 KLCPP1134

35 Agitator 1 KLCPP1135

36 Screw 1 KLCPP11036

37 Fluid Tube 1 KLCPP1137

38 Pick-Up 1 KLCPP1138

39 Filter Support 1 KLCPP1139

40 Filter 1 KLCPP1140

41 Snap ring 1 KLCPP1141

42 Swing bolt 4 KLCPP1142

43 Washer 4 KLCPP1143

44 Wing Nut 4 KLCPP1144

45 Nut 4 KLCPP1145

46 Washer 4 KLCPP1146

47 Caster 4 KLCPP1147

48 Spanner 4 KLCPP1148

49 C-Snap Ring 8 KLCPP1149

Parts List - CPP 11

No. Description Part No: No. Description Part No:

Parts Diagram - CPP 30 & 40

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipos de construcción de Clarke

Clarke

Clarke Strong-Arm CHC500DF Manual de instrucciones

Clarke

Clarke WOODWORKER CTS17 Manual de instrucciones

Clarke

Clarke CAX6TP Manual de usuario

Clarke

Clarke Contractor CCM125D Manual de instrucciones

Clarke

Clarke Strong Arm CHV12B Manual de instrucciones

Clarke

Clarke Strong-Arm CFC2000B Manual del propietario

Clarke

Clarke CHT617 Manual de usuario

Clarke

Clarke Contractor CCM135 Manual de instrucciones

Clarke

Clarke Strong-Arm CFC1000LR Manual del propietario

Clarke

Clarke CAX3TP Manual de usuario

Clarke

Clarke CHT401 Manual de instrucciones

Clarke

Clarke APS-1830 Guía de instalación

Clarke

Clarke CAX10TPB Manual de instrucciones

Clarke

Clarke CAX10TP Manual de instrucciones

Clarke

Clarke SV1A Manual de usuario

Clarke

Clarke CHT264 Manual de instrucciones

Clarke

Clarke ODC8 Manual de usuario

Clarke

Clarke Strong Arm CCB1B Manual de usuario

Clarke

Clarke CHV12 Manual de usuario

Clarke

Clarke CFC2000 Manual de usuario

Clarke

Clarke Strong-Arm CFC1000B Manual del propietario

Clarke

Clarke CCM125P Manual de instalación y operación

Clarke

Clarke CAX2TF Manual de usuario

Clarke

Clarke CFC500F Manual de instalación y operación

Manuales populares de Equipos de construcción de otras marcas

SASFORKS

SASFORKS EXTREME Manual de usuario

Hailo

Hailo H-50 Manual de usuario

Graco

Graco LineLazer ES 1000 Manual de uso y cuidado

Greenlee

Greenlee 555RSC Manual de usuario

Manitowoc

Manitowoc Grove CD3340B Manual de usuario

Lux Tools

Lux Tools A-FMR-20 Set Manual de usuario

SIP

SIP 03683 Manual de usuario

Volvo

Volvo L30G Manual de usuario

Grizzly

Grizzly G8712 Manual de usuario

Modulift

Modulift CMOD 12 Manual de usuario

Case

Case DV201 Manual de usuario

Sealey

Sealey SC10.V2 Manual de usuario

Wacker Neuson

Wacker Neuson DT05 Manual de usuario

HYVA

HYVA AMCO VEBA 81 Series Manual de usuario

Atlas Copco

Atlas Copco Dynapac V5100TV Manual de usuario

Toro

Toro 323 Manual de usuario

Manitowoc

Manitowoc National Crane 1400A Manual de usuario

SGS

SGS EC1500 Manual de usuario