Clarke CAX3TP Manual de usuario

INSTRUCTIONS

GC0219 - Iss 2

3 TONNE AXLE STAND

MODEL NO: CAX3TP

PART NO: 7600065

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS - ALWAYS READ BEFORE USE

• Read these instructions carefully before use.

• Do not exceed the axle stands maximum

load (1.5 tonne each/ 3 tonnes per pair), The

vehicle weight will be in the owners manual.

• Use only as specified in this manual.

• NEVER let children play in or around a vehicle

that is on axle stands.

• ALWAYS make sure that before you work

below the vehicle, a responsible person is

aware in case of injury or accident.

• Do not use more than one pair of axle stands.

• Replace the warning label if it becomes

unreadable.

• Use only on a hard, flat surface for example

concrete.

• Make sure that you chock all the wheels that

remain on the ground.

• Make sure that the supported vehicle cannot

move.

• Set each axle stand below an appropriate

point on the vehicle - See your vehicle

owners manual for advice.

• Take care when using the axle stands on a

three-wheeled vehicle or trailer.

• Upper and lower columns are to be used as a

pair as supplied.

• Use stands as a matched pair to support one end of a vehicle only.

• For your safety, do not modify these axle stands.

WARNING: USE ONLY ON A HARD, FLAT SURFACE FOR EXAMPLE

CONCRETE.

WARNING: NEVER WORK UNDER A VEHICLE SUPPORTED ONLY BY A JACK.

WARNING: AFTER LIFTING THE VEHICLE, SUPPORT IMMEDIATELY WITH

PROPERLY RATED AXLE STANDS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE AXLE STANDS

1. Refer to the vehicle handbook for

the correct jacking procedure and

location of the support points.

ADJUST THE AXLE STAND

1. Remove the locating pin (if fitted).

2. Raise the upper column to the

required height and fit the locating

pin into the lowest hole visible.

3. Insert the retaining pin into the end

of the locating pin to secure in

position.

4. Position the axle stand under a

suitable supporting point. See your

vehicle manual for the location.

LOWERING THE VEHICLE

1. Slowly lower the vehicle onto the

centre of the saddle.

REMOVE THE AXLE STANDS

1. Raise the vehicle clear of the axle stands and remove the stands.

2. Ensure that all tools, equipment and personnel are clear before carefully

lowering the vehicle to the ground.

WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY

PART OF THE AXLE STAND, IF THERE IS, DO NOT USE THE AXLE STAND.

WARNING: IT MUST BE ENSURED THAT THE VEHICLE/LOAD IS CAREFULLY

LOCATED ONTO THE CENTRE OF THE AXLE STAND SADDLE. FAILURE TO DO

THIS CAN RESULT IN DAMAGE TO THE AXLE STANDS, LOSS OF SUPPORT TO

THE LOAD, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.

WARNING: DO NOT EXCEED THE RATED LOAD OF 3 TONNES (PER PAIR).

WARNING: USE ONLY ON A HARD, FLAT SURFACE, E.G. CONCRETE.

WARNING: DO NOT LOAD THE STANDS OFF CENTRE. FAILURE TO HEED THIS

WARNING MAY CAUSE DAMAGE, INJURY OR LOSS OF LIFE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights

SPECIFICATION

Maximum Height 490 mm

Minimum Height 322 mm

Maximum Load 3 Tonnes per pair

Product Weight 5 kg (pair)

Number of Height Positions 5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipos de construcción de Clarke

Clarke

Clarke CAX10TP Manual de instrucciones

Clarke

Clarke Contractor CCM135 Manual de instrucciones

Clarke

Clarke ODC8 Manual de usuario

Clarke

Clarke CPP5 Manual de instalación y operación

Clarke

Clarke Contractor CCM125D Manual de instrucciones

Clarke

Clarke APS-1830 Guía de instalación

Clarke

Clarke Strong Arm CCB1B Manual de usuario

Clarke

Clarke Strong-Arm CFC1000B Manual del propietario

Clarke

Clarke WOODWORKER CTS17 Manual de instrucciones

Clarke

Clarke CAX10TPB Manual de instrucciones

Clarke

Clarke CHT617 Manual de usuario

Clarke

Clarke Strong-Arm CFC2000B Manual del propietario

Clarke

Clarke CHT401 Manual de instrucciones

Clarke

Clarke Strong-Arm CHC500DF Manual de instrucciones

Clarke

Clarke CCM125P Manual de instalación y operación

Clarke

Clarke CHT264 Manual de instrucciones

Clarke

Clarke Strong-Arm CFC1000LR Manual del propietario

Clarke

Clarke CAX2TF Manual de usuario

Clarke

Clarke CFC500F Manual de instalación y operación

Clarke

Clarke CFC2000 Manual de usuario

Clarke

Clarke Strong Arm CHV12B Manual de instrucciones

Clarke

Clarke CAX6TP Manual de usuario

Clarke

Clarke SV1A Manual de usuario

Clarke

Clarke CHV12 Manual de usuario

Manuales populares de Equipos de construcción de otras marcas

SASFORKS

SASFORKS EXTREME Manual de usuario

Hailo

Hailo H-50 Manual de usuario

Graco

Graco LineLazer ES 1000 Manual de uso y cuidado

Greenlee

Greenlee 555RSC Manual de usuario

Manitowoc

Manitowoc Grove CD3340B Manual de usuario

Lux Tools

Lux Tools A-FMR-20 Set Manual de usuario

SIP

SIP 03683 Manual de usuario

Volvo

Volvo L30G Manual de usuario

Grizzly

Grizzly G8712 Manual de usuario

Modulift

Modulift CMOD 12 Manual de usuario

Case

Case DV201 Manual de usuario

Sealey

Sealey SC10.V2 Manual de usuario

Wacker Neuson

Wacker Neuson DT05 Manual de usuario

HYVA

HYVA AMCO VEBA 81 Series Manual de usuario

Atlas Copco

Atlas Copco Dynapac V5100TV Manual de usuario

Toro

Toro 323 Manual de usuario

Manitowoc

Manitowoc National Crane 1400A Manual de usuario

SGS

SGS EC1500 Manual de usuario