Cisco WAP131 Manual de usuario

Quick Start Guide

Cisco Small Business

WAP131 Wireless-N Dual Radio Access Point

with PoE

Package Contents

•Wireless Access Point

•Power Adapter

•This Quick Start Guide

•Product CD

•Ethernet Cable

•Technical Support Contact

•ChinaRoHS(forChinaSKUonly)

2 Cisco WAP131 Quick Start Guide

Welcome

Thank you for choosing the Cisco WAP131 Wireless-N Dual Radio Access

Point with PoE. The Cisco Cisco WAP131 is an indoor concurrent dual band

radio 802.11n access point with Power over Ethernet (PoE).

This guide is designed to familiarize you with the general layout of the

Cisco WAP131, describe how to deploy the Cisco WAP131 in your

network, and describe how to configure the Cisco WAP131. For additional

information, see www.cisco.com/go/100_wap_resources.

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

•A computer with browser support for:

– Internet Explorer 7.0 or later

– Chrome 5.0 or later

– Firefox 3.0 or later

– Safari 3.0 or later

•One or more Ethernet network switches with PoE

Cisco WAP131 Features

Front Panel

The front panel of the Cisco WAP131 consists of three lights: Power,

WLAN, and LAN. For full descriptions of the colors of the lights and their

indications, see “Verifying the Hardware Installation”.

Back Panel

RESET—See “Rebooting the Cisco WAP131 or Returning it to its

Factory Default Settings” for information on the RESET button.

LAN (PoE)—The RJ-45 Ethernet port is used to power the Cisco WAP131

using PoE. It is an auto-sensing, gigabit Ethernet (802.3) port used to

connect your WAP devices to network devices, such as computers,

routers, or switches. We strongly recommend that you use a Category

5e or better cable for gigabit connectivity.

Cisco WAP131 Quick Start Guide 3

POWER—The POWER button is used to turn the power on and off. It is not

applicable when using PoE.

12V DC—The 12V DC jack is used to connect the supplied power adapter

to the Cisco WAP131 if you are not using PoE.

Kensington Lock Slot—The Kensington lock slot is used to attach a cable

and lock to the Cisco WAP131.

Default Settings

If you are using a Cisco Small Business RV Series router, the default range

for the DHCP assigned address is from 192.168.1.100 to 192.168.1.254.

Any device connecting to the same LAN will be assigned an IP address in

this range.

Mounting the Cisco WAP131

You can place the Cisco WAP131 on a desktop.

Placement Tips

• Ambient Temperature—To prevent the Cisco WAP131 from

overheating, do not operate it in an area that exceeds an ambient

temperature of 104°F (40°C).

•AirFlow—Both side panels have vents that must be unobstructed to

prevent overheating.

• Mechanical Loading—The Cisco WAP131 should be level, stable, and

secure to prevent it from sliding or shifting out of position.

Parameter Default Value

Username cisco

Password cisco

LAN IP Address DHCP address assigned by server

Fallback LAN IP 192.168.1.245

Subnetwork Mask 255.255.255.0

4 Cisco WAP131 Quick Start Guide

Connecting the Cisco WAP131

The default configuration of the Cisco WAP131 has the Wi-Fi radio turned

off. You must perform the initial configuration using a wired Ethernet

connection.

To connect the Cisco WAP131 to the wired network:

STEP 1Connect the Ethernet cable to the Ethernet port of a switch, a router,

or a PC.

STEP 2Connect the other end of the network Ethernet cable to the

Ethernet port of the Cisco WAP131.

STEP 3If PoE is not provided, plug in the supplied power adapter to

provide power to the Cisco WAP131.

After installation, all lights should be active. Refer to Verifying the

Hardware Installation, page 5 for details about the different lights on the

Cisco WAP131.

Cisco WAP131 Quick Start Guide 5

Verifying the Hardware Installation

To verify the hardware installation, complete the following tasks:

•Check the cable connections.

•Check the state of the indicator lights.

NOTE If you need help resolving a problem, visit the Cisco Small Business

Support Community at www.cisco.com/go/smallbizsupport.

Label Activity Description

POWER Off The Cisco WAP131 has no power.

Solid Green The Cisco WAP131 is powered on, booting, or in

normal operation with DC power supply.

Solid Blue The Cisco WAP131 is powered on, booting, or in

normal operation with PoE 802.at power supply.

Solid Amber The Cisco WAP131 is powered on, booting, or in

normal operation with PoE 802.af power supply.

Solid Red The Cisco WAP131 fails to boot with both

firmware images.

Flashing The Cisco WAP131 is upgrading the firmware,

or is acquiring an IPv4 or IPv6 address.

WLAN Off Wireless is disabled, for both 2.4 GHz and 5

GHz.

Solid Green Wireless is enabled in concurrent mode. (The

intensity needs to be the same)

Solid Amber Wireless is enabled with only 5 GHz in use.

Solid Blue Wireless is enabled with only 2.4 GHz in use.

Flashing Transmitting or receiving data.

LAN Off No Ethernet link.

Solid Green GE Ethernet link is active.

Solid Amber FE Ethernet link is active.

Flashing Transmitting or receiving data.

6 Cisco WAP131 Quick Start Guide

Getting Started with the Configuration

To configure the Cisco WAP131, follow these steps to access the Wizard

and then the web-based Configuration Utility from your computer:

STEP 1Connect the Cisco WAP131 to the same network (IP subnet) as your

computer. The factory default IP address configuration of the Cisco

WAP131 is DHCP. Make sure that your DHCP server is running and

can be reached.

See “Incorrect IP Address” on page 8 for troubleshooting

information, or if you do not have a DHCP server.

STEP 2Locate the IP address of the Cisco WAP131.

a. The Cisco WAP131 can be accessed and managed by Cisco

Small Business network tools and services including the Cisco

FindIT Network Discovery Utility that enables you to

automatically discover all supported Cisco Small Business

devices in the same local network segment as your computer.

You can get a snapshot view of each device or launch the

product Configuration Utility to view and configure the

settings. For more information, see www.cisco.com/go/findit.

b. The Cisco WAP131 is Bonjour-enabled and automatically

broadcasts its services and listens for services being

advertised by other Bonjour-enabled devices. If you have a

Bonjour-enabled browser, such as Microsoft Internet Explorer

with a Bonjour plug-in, or the Apple Mac Safari browser, you

can find the Cisco WAP131 on your local network without

knowing its IP address.

You can download the complete Bonjour for Microsoft Internet

Explorer browser from Apple’s website by visiting:

http://www.apple.com/bonjour/

c. Locate the IP address assigned by your DHCP server by

accessing your router or DHCP server. See your DHCP server

instructions for more information.

STEP 3Launch a web browser, such as Microsoft Internet Explorer.

STEP 4In the Address field, enter the default DHCP address and press the

Enter key.

STEP 5Enter the default user name of cisco and password of cisco in the

User Name and Password fields.

STEP 6Click Login. The Wireless Access Point Setup Wizard appears.

Cisco WAP131 Quick Start Guide 7

STEP 7Follow the Setup Wizard instructions to finish the WAP device

installation. We strongly recommend that you use the Setup

Wizard for the first installation.The Setup Wizard turns on the Wi-Fi

radio, which allows you to connect wirelessly. For more advanced

configurations, see the Administration Guide.

Congratulations, you can now start using your Cisco WAP131.

Suggested Next Steps

In case of an error while installing, try the following troubleshooting

procedures described in this section:

Troubleshooting

If you cannot display the Configuration Utility, you can test the ability of the

computer to communicate with the wireless access point by using ping. To

use ping on a computer running Windows:

STEP 1Verify that the Cisco WAP131is powered on and the lights indicate

the appropriate links.

STEP 2Locate the Cisco WAP131’s IP address. While there are different

ways to locate the Cisco WAP131’s IP address, this procedure

uses Cisco FindIT.

a. If you have previously downloaded Cisco FindIT, open Internet

Explorer and launch Cisco FindIT. For more information on

downloading Cisco FindIT, see www.cisco.com/go/findit.

b. In the Cisco FindIT display, place your mouse over the Cisco

WAP131’s name. The Cisco WAP131’s IP address is displayed

along with other device information.

STEP 3Open a command window by choosing Start > Run and enter

cmd.

STEP 4At the command window prompt, enter ping and the Cisco

WAP131’s IP address. In this example, we pinged 192.0.2.10.

If successful, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data:

Reply from 192.0.2.10: bytes=32 time<1ms TTL=128

8 Cisco WAP131 Quick Start Guide

If it fails, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data:

Request timed out.

Possible Cause of Installation Failure

Devices Cant Connect using Wi-Fi

Complete the Setup Wizard. The Wi-Fi radio on the Cisco WAP131 is

turned off by default, and the Setup Wizard activates it. For users who do

not want to use the Setup Wizard, log into the Cisco WAP131 using a

Category 5e Ethernet cable, and activate the Wi-Fi radio manually. See the

Administration Guide for details on activating the Wi-Fi radio.

No Power

Power up the switch and your computer if they are turned off.

Make sure that your PoE switch is powered on and the lights indicate that

you have a link. See “Verifying the Hardware Installation” on page 5.

Verify that the devices on your network are not plugged into a switchable

outlet.

Bad Ethernet Connection

Check the state of the indicator lights. See “Verifying the Hardware

Installation” on page 5.

Check the Ethernet cable to ensure that it is firmly connected to your

devices. Devices connected by the Ethernet cable can include the WAP

device, and routers, any switches, and your computer.

Verify the connected switch has auto-negotiation enabled. The Cisco

WAP131 and the switch need the same negotiation parameters set.

Bad Image

After a new firmware installation, if the POWER light is flashing quickly,

contact system support; see “Where to Go From Here” on page 10.

Incorrect IP Address

The most likely cause of connectivity failure is an incorrect IP address. The

Web browser may be pointing to the wrong IP address, or your computer

may be configured with an IP address that is not in the same subnet as the

wireless access point.

Cisco WAP131 Quick Start Guide 9

Because the factory default IP address configuration is DHCP, make sure

that your DHCP server is running and can be reached. You may need to

disconnect and reconnect the devices for them to discover their new IP

addresses from the DHCP server. You can then query the DHCP server for

the new IP address. See Step 2 of “Getting Started with the

Configuration” on page 6 for more information on how to find the DHCP

address.

If the Cisco WAP131 does not receive a DHCP response (there is no DHCP

server on your network) after 60 seconds, the Cisco WAP131 will fallback

to the following default static IP address: 192.168.1.245 and a default mask

of 255.255.255.0. To reach that IP address, be sure that your computer is

on the 192.168.1.xxx network.

Rebooting the Cisco WAP131 or Returning

it to its Factory Default Settings

To reboot your Cisco WAP131:

•When the power supply is PoE, unplug your Ethernet connection for

three seconds and plug it back in.

•With the power on, press the RESET button with an opened paper clip

for less than 10 seconds, or until the lights go off.

– When all the lights go off, release the RESET button.

– Release the RESET button as soon as the lights go off, or you will

restore the access point to factory default settings and lose your

configurations.

To reset the Cisco WAP131 to factory default settings:

•With the power on, press and hold the RESET button with an opened

paper clip for more than 10 seconds.

– All of the lights will go off.

– Release the RESET button when the power light turns on.

10 Cisco WAP131 Quick Start Guide

Where to Go From Here

For EU lot 26 related test result, please check this web page:

www.cisco.com/go/eu-lot26-results.

Support

Cisco Small Business

Support Community

www.cisco.com/go/smallbizsupport

Cisco Small Business

Support and Resources

www.cisco.com/go/smallbizhelp

Phone Support Contacts www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Small Business

Firmware Downloads

www.cisco.com/go/smallbizfirmware

Select a link to download firmware for Cisco

Small Business Products. No login is

required.

Downloads for all other Cisco Small Business

products, including Network Storage

Systems, are available in the Download area

on Cisco.com at www.cisco.com/go/

software (registration/login required).

Cisco Small Business

Open Source Requests

www.cisco.com/go/

smallbiz_opensource_request

Product Documentation

Cisco WAP131

Administration Guide

www.cisco.com/go/100_wap_resources

Cisco Small Business

Power Adapters

Go to www.cisco.com/go/wap_accessories

and select the Resources tab. Scroll down to

Technical Documentation.

Cisco Small Business

Cisco Partner Central for

Small Business (Partner

www.cisco.com/web/partners/sell/smb

Cisco Small Business

Home

www.cisco.com/smb

Otros manuales para WAP131

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Small Business WAP551 Manual de usuario

Cisco

Cisco Linksys Wireless-G WBP54GV2 Manual de usuario

Cisco

Cisco Linksys WAP54GX Instrucciones de funcionamiento originales

Cisco

Cisco Aironet 1570 Series Manual de usuario

Cisco

Cisco Aironet 1530 Series Manual

Cisco

Cisco DPH650 Manual de usuario

Cisco

Cisco Meraki MR33 Manual de usuario

Cisco

Cisco Meraki MR70 Manual de usuario

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Manual de instrucciones

Cisco

Cisco WAP571E Manual de usuario

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 Manual de usuario

Cisco

Cisco Aironet 1815i Manual de usuario

Cisco

Cisco Aironet 1400 Series Manual de usuario

Cisco

Cisco Catalyst Wireless 9163E Manual de usuario

Cisco

Cisco WAP300N Manual de usuario

Cisco

Cisco WAP371 Manual de usuario

Cisco

Cisco Aironet 1572EC Guía de referencia rápida

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de instrucciones

Cisco

Cisco 700 series Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Cisco

Cisco Aironet 1540 Series Manual

Cisco

Cisco Catalyst 9166 Series Manual

Cisco

Cisco WAP571 Manual de instrucciones

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario