Cisco Catalyst 9500 Series Instrucciones de funcionamiento
Troubleshooting
•Getting Started, on page 1
•Solving Problems at the System Component Level, on page 1
•Identifying Startup Problems, on page 2
•Troubleshooting the Power Supply, on page 2
•Troubleshooting the Fan Tray , on page 3
•Status LED Indicators, on page 3
•Contacting Cisco Customer Service, on page 3
•Finding the Serial Number, on page 4
Getting Started
When the initial system startup is complete, verify the following:
• Power supplies are supplying power to the system.
• The fan tray assembly is operating.
• System software boots successfully.
If one or more of the above conditions are not met, use the procedures described in this chapter to isolate and,
if possible, resolve the problem. If all of the above conditions are met, and the hardware installation is complete,
refer to your software release notes for hardware support information and software caveats.
Solving Problems at the System Component Level
The key to success when troubleshooting the system is to isolate the problem to a specific system component.
The first step is to compare what the system is doing to what it should be doing. Because a startup problem
can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather
than troubleshoot each separate component in the system.
The switch consists of these subsystems:
• Power supplies
• Fan tray assembly
Troubleshooting
1
The chassis fan tray assembly should operate whenever system power is on. You should see the FAN
LED turn green and hear the fan tray assembly operating. A red or amber FAN LED indicates that one
or more fans in the fan tray assembly is not operating. You should immediately contact a Customer
Service representative if the fan tray assembly is not functioning properly. There are no installation
adjustments that you can make if the fan tray assembly does not function properly at initial startup.
Identifying Startup Problems
LEDs indicate all system states in the startup sequence. By checking the LEDs, you can determine when and
where the system failed in the startup sequence.
Procedure
Step 1 Turn on the power supplies. You should immediately hear the system fan tray assembly begin to operate.
Step 2 If the startup information and system banner do not display at startup, verify that the terminal is set correctly
and that it is connected properly to the console port.
Troubleshooting the Power Supply
If the Power Supply LED does not light after you turn on the power switch, follow these steps to isolate a
power subsystem problem:
Procedure
Step 1 Verify that the Power Supply LED on the power supply is green.
• If the Power Supply LED is green, the AC or DC source is good and the power supply is functional.
• If the Power Supply LED remains off, there might be a problem with the AC source, the DC source, or
the power cable.
• Turn off the power to the switch, connect the power cord to another power source if one is available, and
turn on the power.
• If the Power Supply LED is green, the problem is the first power source.
• If the Power Supply LED fails to light after you connect the power supply to a new power source, replace
the power cord, and turn on the switch.
• If the Power Supply LED then goes on, return the first power cord for replacement.
If this unit has more than one power cord, repeat Step 1 for each power supply.
If the Power Supply LED still fails to light when the switch is connected to a different power source with a
new power cord, the power supply is probably faulty.
Troubleshooting
2
Troubleshooting
Identifying Startup Problems
If a second power supply is available, install it in the second power supply bay, and contact a customer service
representative for further instructions.
Step 2 If you have a second power supply, repeat Step 1 for this power supply.
What to do next
If you are unable to resolve the problem or if you determine that either a power supply or backplane connector
is faulty, see Contacting Cisco Customer Service, on page 3.
Troubleshooting the Fan Tray
To isolate a fan tray problem, follow these steps:
Procedure
Step 1 Verify that the FAN LED on the fan tray is green.
If the FAN LED is not green, see Fan LED to determine whether or not the power subsystem is functioning
properly.
Step 2 Check to determine if the FAN LED is red or amber. If the FAN LED is red, one or more fans' tachometer
faults have exceeded the maximum limit. If the FAN LED is amber, one or more fans have encountered
tachometer faults.
Do the following:
• To ensure that the fan tray is seated properly, loosen the captive installation screws, remove the fan tray,
and reinstall it.
• Tighten all captive installation screws, and then restart the system.
• If the FAN LED is still red or amber, the system detects an individual fan failure. Contact a customer
service representative for instructions.
Status LED Indicators
Refer to "System LED" section in the "Product Overview" chapter. More details will be added here later.
Contacting Cisco Customer Service
If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contact
a Cisco customer service representative for assistance and additional instructions. Before you call, have the
following information ready to help your service provider assist you as quickly as possible:
Troubleshooting
3
Troubleshooting
Troubleshooting the Fan Tray
• Date on which you received the switch
• Chassis serial number
• Type of software and release number
• Maintenance agreement or warranty information
• Brief description of the problem
• Brief explanation of the steps you have already taken to isolate and resolve the problem
Finding the Serial Number
If you contact Cisco Technical Assistance, you need to know the switch serial number. The figure shows
where the serial number is located. You can also use the show version privileged EXEC command to see the
serial number.
Figure 1: Serial Number Location and Switch Labels
Serial number of the switch is located at the top of the switch. Following illustrations show all the labels at
the top and the bottom of the switch.
Serial Number6Mult1 Power Warning1
Laser Warning7Fan Tray Warning2
Caution ESD8RFID3
Lab Altitude9CLEI4
Compliance label10MAC Number5
Troubleshooting
4
Troubleshooting
Finding the Serial Number
Otros manuales para Catalyst 9500 Series
8
Tabla de contenidos
Otros manuales de Cambiar de Cisco
Cisco
Cisco Catalyst WS-C2924-XL Manual
Cisco
Cisco CDB-8U Manual de usuario
Cisco
Cisco Catalyst 3650 Series Manual
Cisco
Cisco Nexus 9332D-GX2B Manual
Cisco
Cisco Catalyst 4500 Series Manual de instrucciones
Cisco
Cisco MGC Node Manager Manual de usuario
Cisco
Cisco 3750 - Catalyst EMI Switch Manual de usuario
Cisco
Cisco Catalyst 4500 E Series Supervisor Engine 9-E Guía rápida
Cisco
Cisco Catalyst IE9300 Manual
Cisco
Cisco SRW248G4 - Small Business Managed Switch Manual de usuario
Cisco
Cisco Catalyst 2960-XR Manual de usuario
Cisco
Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manual
Cisco
Cisco PIX 520 - PIX Firewall 520 Manual de usuario
Cisco
Cisco Nexus 9348GC-FXP NX-OS Manual
Cisco
Cisco NME-16ES-1G - Etherswitch Service Mod 16 Hoja de especificaciones
Cisco
Cisco Catalyst Series Switch 2940 Manual de usuario
Cisco
Cisco Meraki MS250 Series Manual de usuario
Cisco
Cisco WS-C3524-PWR-XL-EN Manual de usuario
Cisco
Cisco MDS 9120 - Fabric Switch Manual de usuario
Cisco
Cisco IE 2000 Cómo utilizar
