Cisco 7513 Series Manual de usuario
INSTALL THE HARDWARE
CONNECT THE RSP
START AND CONFIGURE THE SYSTEM
INSTALL FIELD REPLACEABLE UNITS (FRUS)
1
2
3
4
Quick Start Guide
IsCiscodocumentationhelpful?Clickhereorgotohttp://www.cisco.com/warp/public/732/docsurvey/rtg/togive
us your feedback.
CISCO 7513 AND 7576 ROUTERS
5
POWER
A
POWER
B NORMAL
1
Install the Hardware
EJECT
SLOT0
SLOT1
NORMAL
CPUHALT
RESET
AUX.
CONSOLE
ROUTESWITCH PROCESSOR 2
SLAVE
MASTER
SLAVE/MASTER
ENABLE
ENABLE
EJECT
SLOT0
SLOT1
NORMAL
CPUHALT
RESET
AUX.
CONSOLE
ROUTESWITCH PROCESSOR 2
SLAVE
MASTER
SLAVE/MASTER
0
I
AC
OK FAN
OK OUTPUT
FAIL
0
I
AC
OK FAN
OK OUTPUT
FAIL
POWER
A
POWER
B
53385
Blower module
Cable-management
bracket
Card cage and
processor
modules
Air intake vent
Power supplies
Chassis
grounding
receptacles
Interface
processor slot
numbering
scheme
The Cisco 7513 has 13 slots: interface processor
slots0through5,RouteSwitchProcessorslots6and
7, and interface processor slots 8 through 12.
The Cisco 7576 router is two Cisco 7500 series
routers configured on a single split backplane, with
13 slots. Router A uses interface processor slots 0
through 5 with a Route Switch Processor in slot 6.
Router B uses interface processor slots 8 through 12
with a Route Switch Processor in slot 7.
The Cisco 7513 and Cisco 7576 routers have bays
for up to two AC-input or DC-input power supplies.
Each chassis will operate with one power supply, but
a second power supply allows load sharing and
increased system availability.
Note The Cisco 7576 does not support the high
system availability (HSA) feature. The RSP in slot 6
is automatically the system master for router A and
the RSP in slot 7 is automatically the system master
for router B.
Note If you are only configuring one of the two
Cisco 7576 internal routers, configure router A
instead of router B. Install an RSP in slot 6, and
interface processors in slots 0 through 5.
Packing List
• 1 Cisco 7513 or 7576 router
• 1 Route Switch Processor (RSP)
• Y-adapter cables, 1 auxiliary and 1 console
• 1 AC power supply
• 1 AC power supply cable
• 1 Power cord
• 1 Anti-static wrist strap and documentation
2
Prepare to Install the Router
Install the Hardware
Note For detailed hardware installation
instructions and safety guidelines, refer to the Cisco
7500 Series Router Installation and Configuration
Guide, Site Preparation and Safety Guide, and the
Cisco 7500 Regulatory Compliance and Safety
Guide.
Warning Only trained and qualified
personnel should install, replace, or service
this equipment.
Step 1 Lift the router safely out of the packing
container.
Step 2 Ensure the power service at the site is
suitable for the router you are installing.
Step 3 Check the packing slip to ensure that all
the proper components are present.
Step 4 Confirm that you have the required tools
and parts:
For rack-mounting (optional):
• Number 1 and Number 2 Phillips screwdrivers
• 1/4-inch and 3/16-inch flat-blade screwdrivers
• Tape measure
• Level (optional)
• Twomounting brackets (identical),each with an
attached spanner bar
• Two chassis ears with captive grommets
(identical)
• Four M4 x 10-mm Phillips flat-head screws to
secure the ears to the chassis
• Twelve 10-32 x 5/8-inch LG Phillips pan-head
screws with integral square cone washers
For cable-management brackets:
• Number 1 Phillips screwdriver
• Two cable-management brackets
• Six M3 x 8-mm Phillips pan-head screws
For interface modules:
• Number 1 Phillips or 3/16-inch flat-blade
screwdriver
For DC-Input Power Supply:
• Twin-lead, 10-AWG cable terminal block
connection
• Single 8-AWG wire for the ground connection
• 3/16-inch flat-blade screwdriver
• 8-mm nut driver
3
Install the Router on a Bench or Tabletop
Install the Hardware
POWER
A
POWER
B
H3118
Note To rack-mount the router, refer to the
“Rack-Mount the Router (Recommended)” section
on page 4.
Caution Two people are required to
perform this step. Avoid sudden twists or
moves to prevent injury.
Step 1 With a person positioned at either side of
the chassis, grasp the bottom edge of the
chassis with one hand near the front and
the other near the back. Slowly lift the
chassis in unison. Place the chassis on a
bench or tabletop where the air intake
vent on the front of the chassis is not
drawing in exhaust air from other
equipment.
Warning When lifting the router, do not
lift by grasping the handle of the blower
module, nor should you grasp the air intake
grill.
Step 2 Ensure that you have at least 2 or 3 feet
(0.6to.09m)ofclearancearoundtherear
ofthechassistoinstallpowersupplies and
perform maintenance on the chassis.
Step 3 Proceed to the “Install Interface
Processors, Fillers, VIPs, or RSPs” section
on page 9.
4
Rack-Mount the Router (Recommended)
Install the Hardware
H3172
POWER
APOWER
B
10-32 x 5/8 in. long
Phillips pan-head screws
with integral square cone
washers (for mounting
brackets and chassis
ears to rack posts)
Chassis ear (cutaway of frame post
to enable view of chassis ear)
M4 x 10-mm long
Phillips flat-head
screws (to attach
ears to chassis)
Bracket (2)
To rack-mount the Cisco 7513 or Cisco 7576 router,
you will perform the following steps:
Step 1 Mount the brackets to the rack posts.
Step 2 Secure the spanner bars.
Step 3 Attach the chassis ears.
Step 4 Mount the chassis.
5
Mount Brackets to the Rack Posts
Install the Hardware
53382
Rack post
Flange
Shielded side
Note The distance between the inner edges of the
left and right rack-mounting posts must be at least
17.72 inches (45.088 cm), and the distance between
theholes in the mounting posts must be 18.31 inches
(46.5 cm) (+ .063 inches or .16 cm).
Step 1 Place the bracket on the inner side of the
rack post, with the flanged front edge of
the bracket in front of the rack post.
Step 2 Align the mounting holes in the bracket
with those in the rack post.
Step 3 Support the bracket with one hand, and
use the other hand to insert a 10-32 x
5/8-inch LG Phillips pan-head screw
through the bottom mounting hole on the
front of the bracket and into the rack post.
Step 4 Secure the top of the bracket to the rack
with two pan-head screws. Finger-tighten
the screws.
Step 5 Push the brackets as far apart as possible
before using a Number 2 Phillips
screwdriver to tighten the screws.
Step 6 Adjust the brackets if the distance
between them is less than 17.5 inches
(45.45 cm).
Step 7 Repeat Step 3 through Step 6 for the
remaining bracket. Use a level or tape
measure to ensure that the two brackets
are level in the rack.
6
Secure the Spacers
Install the Hardware
53425
A
B
C
Step 1 Loosen the 10-32 x 5/8-inch LG Phillips
pan-head screw at the end of the ledge of
the right-side bracket. This screw is the
anchor for the spanner bar.
Step 2 Remove the tape that secures the spanner
bar on the left bracket, and swing the bar
down(seeA) over the anchor screw on the
opposite bracket (see B).
Step 3 If the spanner bar does not reach the
opposite bracket, loosen the pan-head
screws to allow more play between the
brackets, and adjust brackets as needed.
Step 4 RepeatStep 1 through Step 3 tofasten the
remainingspannerbartoitsanchorscrew.
(See C.)
Step 5 Push the brackets as far apart as possible
before tightening the screws.
Step 6 Use a Number 2 Phillips screwdriver to
tighten the six pan-head screws that
secure the brackets to the rack-mounting
posts, and the two anchor screws that
secure the spanner bars.
Step 7 Adjust the brackets if the distance
between them is less than 17.5 inches
(44.45 cm).
7
Attach the Chassis Ears
Install the Hardware
H3174
POWER
B
POWER
A
Center-mount position
Flush-mount position
Step 1 Position the ears on the chassis as follows:
• To flush-mount the chassis, place each ear so
thatthemountingstrips are flush withtheendof
the chassis, and align the mounting holes in the
ear with those in the chassis.
• To center-mount the chassis, place each ear with
the mounting strips away from the end of the
chassis, and align the mounting holes in the ear
with those in the chassis.
Step 2 Use two M4 x 10-mm LG Phillips
flat-head screws to secure each ear to the
chassis.
8
Mount the Chassis in the Rack
Install the Hardware
53487
POWER
APOWER
B
Caution Two people are required to
perform this step.
Step 1 With a person positioned at either side of
the chassis, grasp the bottom edge of the
chassis with one hand near the front and
the other near the back.
Step 2 Slowly lift the chassis in unison. Avoid
sudden twists or moves to prevent injury.
Step 3 With the chassis positioned so the front is
closest to the rack, insert the front of the
chassisintotherackbetweenthebrackets,
and then slowly lower the chassis until it
rests on the two bracket ledges.
Step 4 Slide the chassis back into the rack along
the ledges until the ears meet the front
mounting posts on both sides of the rack.
Step 5 Secure each ear to the rack-mounting post
with two 10-32 x 5/8-inch LG Phillips
pan-head screws.
Otros manuales para 7513 Series
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Enrutador de red de Cisco
Cisco
Cisco Performance Routing Engine 5 Manual de usuario
Cisco
Cisco 4000-M series Manual de lista de piezas
Cisco
Cisco 7200 VXR Series Manual de usuario
Cisco
Cisco BEFSR41 Manual de usuario
Cisco
Cisco 1811W - Integrated Services Router Wireless Manual de usuario
Cisco
Cisco 700 series Manual de usuario
Cisco
Cisco ASR 9000 Series Manual de instrucciones
Cisco
Cisco Nexus 1000V Manual de usuario
Cisco
Cisco 10005 ESR Manual de usuario
Cisco
Cisco 7401 Manual de usuario
Cisco
Cisco 8200 Series Manual
Cisco
Cisco SOHO 91 Manual de usuario
Cisco
Cisco IR809 Manual de usuario
Cisco
Cisco vEdge Series Manual
Cisco
Cisco 7609 Manual de instrucciones
Cisco
Cisco Profile Series Manual de usuario
Cisco
Cisco 1841 - 1841 Integrated Services Router Manual
Cisco
Cisco XR 12416 Manual de usuario
Cisco
Cisco 3000 Series Manual de instrucciones
Cisco
Cisco 1600 series Manual de usuario
