Cisco 8200 Series Manual

Hardware Installation Guide for Cisco 8200 Series Routers

First Published: 2020-03-15

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

CONTENTS

Cisco 8200 Series Routers Overview 1

CHAPTER 1

Cisco 8200 Series Routers 1

Prepare for Installation 3

CHAPTER 2

Safety Guidelines 3

Compliance and Safety Information 4

Laser Safety 4

Energy Hazard 4

Preventing Electrostatic Discharge Damage 5

Cautions and Regulatory Compliance Statements for NEBS 5

Installation Guidelines 6

Procure Tools and Equipment 6

Accessory Kit 7

Prepare Your Location 7

Prepare Yourself 8

Prepare Rack for Chassis Installation 9

Clearance Requirements 10

Installing the Chassis 13

CHAPTER 3

Rack Mount the Chassis 13

Rack-Mount the Chassis in a 4-Post Rack 13

Rack-Mount the Chassis in a 2-Post Rack 17

Ground the Chassis 20

Connect AC Power to the Chassis 21

Connect DC Power to the Chassis 23

Hardware Installation Guide for Cisco 8200 Series Routers

iii

Connect Router to the Network 25

CHAPTER 4

Port Connection Guidelines 25

Interfaces and Port Description 26

Connecting a Console to the Router 28

Create the Initial Router Configuration 29

Connect the Management Interface 31

Install and Remove Transceiver Modules 32

Install and Remove QSFP Transceiver Modules 32

Required Tools and Equipment 32

Installing the Transceiver Module 32

Attach the Optical Network Cable 33

Removing the Transceiver Module 34

Connect Interface Ports 34

Connect a Fiber-Optic Port to the Network 34

Disconnect Optical Ports from the Network 35

Maintain Transceivers and Optical Cables 35

Verify Chassis Installation 35

Replace Chassis Components 37

CHAPTER 5

Replace Fan Modules 37

Replace Power Supply 39

LEDs 41

CHAPTER 6

Chassis LEDs 41

Fan Tray LED 43

Power Supply LEDs 44

Port Status LEDs 44

Hardware Installation Guide for Cisco 8200 Series Routers

Contents

CHAPTER 1

Cisco 8200 Series Routers Overview

•Cisco 8200 Series Routers, on page 1

Cisco 8200 Series Routers

The Cisco 8200 Series Routers utilizes Cisco’s new Router-on-Chip (RoC) model to deliver full routing

functionality with a single ASIC per router. The RoC architecture is distinguished from System-on-Chip (SoC)

switches by supporting large forwarding tables, deep buffers, more flexible packet operations, and enhanced

programmability.

The Cisco 8200 series routers presently comprises:

• Cisco 8201 Router – It provides 10.8 Tbps of network bandwidth with dramatically lower power

consumption than contemporary 10 Tbps systems. The Cisco 8201 Router is a fixed port, high density,

one rack unit form-factor router. Supported ports include 24x 400G QSFP56-DD and 12x 100G QSFP28.

For more details on ports and supported breakout options, see "Interfaces and Port Description, on page

26".

Hardware Installation Guide for Cisco 8200 Series Routers

Cisco 8200 Series Routers Overview

Cisco 8200 Series Routers

CHAPTER 2

Prepare for Installation

The images in this chapter are only for representational purposes, unless specified otherwise. The chassis'

actual appearance and size may vary.

Note

Statement 1071—Warning Definition

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

•Safety Guidelines, on page 3

•Compliance and Safety Information, on page 4

•Laser Safety, on page 4

•Energy Hazard, on page 4

•Preventing Electrostatic Discharge Damage, on page 5

•Cautions and Regulatory Compliance Statements for NEBS, on page 5

•Installation Guidelines, on page 6

•Procure Tools and Equipment, on page 6

•Prepare Your Location , on page 7

•Prepare Yourself , on page 8

•Prepare Rack for Chassis Installation, on page 9

•Clearance Requirements, on page 10

Safety Guidelines

Before you perform any procedure in this document, review the safety guidelines in this section to avoid

injuring yourself or damaging the equipment. The following guidelines are for your safety and to protect the

equipment. Because the guidelines do not include all hazards, be constantly alert.

Hardware Installation Guide for Cisco 8200 Series Routers

• Keep the work area clear, smoke and dust-free during and after installation. Do not allow dirt or debris

to enter into any laser-based components.

• Do not wear loose clothing, jewelry, or other items that could get caught in the router or other associated

components.

• Cisco equipment operates safely when used in accordance with its specifications and product-usage

instructions.

• If potentially hazardous conditions exist, do not work alone.

• Take care when connecting multiple units to the supply circuit so that wiring is not overloaded.

• This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority

or an electrician if you are uncertain about whether suitable grounding is available.

• When installing or replacing the unit, the ground connection must always be made first and disconnected

last.

• To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the

handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to

support the weight of the unit.

• Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when

servicing.

Compliance and Safety Information

The Cisco 8000 Series Routers are designed to meet the regulatory compliance and safety approval requirements.

For detailed safety information, see Regulatory Compliance and Safety Information—Cisco 8000 Series

Routers.

Laser Safety

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments.

Warning

Energy Hazard

The routers can be configured for a DC power source. Do not touch terminals while they are live. Observe

the following warning to prevent injury.

Hardware Installation Guide for Cisco 8200 Series Routers

Prepare for Installation

Compliance and Safety Information

Statement 1086—Power Terminals

Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals are

not in service. Be sure uninsulated conductors are not accessible when cover is in place.

Warning

Preventing Electrostatic Discharge Damage

Many router components can be damaged by static electricity. Not exercising the proper electrostatic discharge

(ESD) precautions can result in intermittent or complete component failures. To minimize the potential for

ESD damage, always use an ESD-preventive antistatic wrist strap (or ankle strap) and ensure that it makes

adequate skin contact.

Check the resistance value of the ESD-preventive strap periodically. The measurement should be 1–10

megohms.

Note

Before you perform any of the procedures in this guide, attach an ESD-preventive strap to your wrist and

connect the leash to the chassis.

Cautions and Regulatory Compliance Statements for NEBS

The NEBS-GR-1089-CORE regulatory compliance statements and requirements are discussed in this section.

The intrabuilding port(s) of the equipment or subassembly must use shielded intrabuilding cabling/wiring that

is grounded at both ends. Statement 7003

Warning

The intrabuilding port(s) of the equipment or subassembly must not be metallically connected to interfaces

that connect to the OSP or its wiring. These interfaces are designed for use as intrabuilding interfaces only

(Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling.

The addition of Primary Protectors is not sufficient protection in order to connect these interfaces metallically

to OSP wiring. Statement 7005

Warning

This equipment shall be connected to AC mains provided with a surge protective device (SPD) at the service

equipment complying with NFPA 70, the National Electrical Code (NEC). Statement 7012

Warning

This equipment is suitable for installations utilizing the insert Common Bonding Network (CBN). Statement

7013

Warning

Hardware Installation Guide for Cisco 8200 Series Routers

Prepare for Installation

Preventing Electrostatic Discharge Damage

The battery return conductor of this equipment shall be treated as (DC-I). Statement 7016

Warning

This equipment is suitable for installation in Network Telecommunications Facilities. Statement 8015

Warning

This equipment is suitable for installation in locations where the NEC applies. Statement 8016

Warning

Installation Guidelines

Before installing the chassis, ensure that the following guidelines are met:

• Site is properly prepared so that there is sufficient room for installation and maintenance.

• Operating environment is within the ranges that are listed in Environment and Physical specifications.

• Chassis is mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting the chassis in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

chassis in the rack.

• Airflow around the chassis and through the vents is unrestricted.

• Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting

fixtures. Make sure that the cabling is safely away from other devices that might damage the cables.

• Each port must match the wave-length specifications on each end of the cable, and the cable must not

exceed the stipulated cable length.

Cisco 8000 Series Routers function in operating temperatures of up to 40 degrees C at sea level. For every

300 meters (1000 feet) elevation, the maximum temperature is reduced by 1 degrees C. For more details on

environmental requirements, see Cisco 8000 Series Routers Data Sheet.

Note

Procure Tools and Equipment

Obtain these necessary tools and equipment for installing the chassis:

• Number 1 and number 2 Phillips screwdrivers with torque capability to rack-mount the chassis.

• 3/16-inch flat-blade screwdriver.

• Tape measure and level.

Hardware Installation Guide for Cisco 8200 Series Routers

Prepare for Installation

Installation Guidelines

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco uBR925 Guía de configuración

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Instrucciones de funcionamiento

Cisco

Cisco ASR 9901 Manual de usuario

Cisco

Cisco SOHO Series Manual de usuario

Cisco

Cisco 1721 - VPN Security Router Bundle Manual

Cisco

Cisco NCS 5000 Series Manual de usuario

Cisco

Cisco Linksys WET11 Manual de usuario

Cisco

Cisco 2654T6 Manual de usuario

Cisco

Cisco WGA54G Manual de usuario

Cisco

Cisco Nexus 5500 Series NX-OS Manual de usuario

Cisco

Cisco C1109-2PX Guía de inicio rápido

Cisco

Cisco Linksys WRT610N Manual de usuario

Cisco

Cisco 500 Series Manual de usuario

Cisco

Cisco Linksys WRT54G3G Manual de usuario

Cisco

Cisco 7200 VXR Series Manual de usuario

Cisco

Cisco Card Cage and Backplane 7513-MX Guía

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manual de usuario

Cisco

Cisco 815 Manual

Cisco

Cisco 2431 - IAD Router Manual

Cisco

Cisco 887V - Integrated Services Router Manual de usuario

Cisco

Cisco SRW208MP Manual de usuario

Cisco

Cisco ME 3400G-2CS - Ethernet Access Switch Manual de usuario

Cisco

Cisco 2650 - 2650 Router Manual

Cisco

Cisco Small Business Pro SRP527W Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario