Cisco MA-UMNT-MR-A3 Manual de usuario

MA-UMNT-MR-A3 Aruba Mounting Adapter Installation Guide

Overview

The MA-UMNT-MR-A3 is a universal mounting adapter designed to simplify the transition from Aruba to Cisco Meraki access points. This adapter works with

MR33, MR42/42E, MR52, MR53/53E, MR45/55, MR36/46/46E/56 indoor access points. MA-UMNT-MR-A3 can be attached directly to the Aruba mount without

the need to remove this mount from its current mounting location. Supported Aruba mounts: JW046A, JW047A, AP-200-MNT-W2, AP-220-MNT-W2,

AP-220-MNT-W2W.

Package Contents

MA-UMNT-MR-A3 standard package includes the following equipment:

•1x MA-UMNT-MR-A3

•1x PH#2 M4XP0.6X14L security screw

•2x PH 19mm long screws, M3.5 threads

•1x TORX M4XP0.6X14L security screw

Note: The MA-UMNT-MR-A3 does not work with any of the outdoor MR access points.

Note: The MA-UMNT-MR-A3 cannot mount Meraki access points by itself and must be paired with one of the listed Aruba mounts.

Collect Tools

You will need the following tools to perform an installation:

1x Phillips head screwdriver

1x TORX screwdriver

Installation Instructions

Remove the current Aruba access point from the Aruba mount and ensure that the security lock on MA-UMNT-MR-A3 is not engaged.

1. If JW046A / JW047A Aruba mounts are used, position the MA-UMNT-MR-A3 to align with the currently installed Aruba mount, placing the MA-UMNT-

MR-A3 so that it’s mounting tabs are at an angle of approximately 30 degrees to the Aruba mount. Pushing toward the wall, rotate the MA-UMNT-MR-A3

clockwise until it clicks into place.

If AP-200-MNT-W2 / AP-220-MNT-W2 / AP-220-MNT-W2W Aruba mounts are used, align the pins on the rear panel of the MA-UMNT-MR-A3 with the slots on

the Aruba mount plate. Press the button on the bottom on the Aruba mount in and slide the MA-UMNT-MR-A3 into the Aruba mount until the pins are fully

engaged. Release the button to secure the MA-UMNT-MR-A3 to the Aruba mount. For additional security, insert the Torx security screw into the hole located

next to the button to lock the MA-UMNT-MR-A3 to the Aruba mount.

2. Use a Phillips head screwdriver to secure MA-UMNT-MR-A3 and ensure it’s in a locked position.

3. Use the two Phillips head screws included in the mount kit to attach your Meraki mount cradle to the MA-UMNT-MR-A3 mount.

Attach your Meraki access point to the Meraki mount cradle by lining up the top edge of the AP with the top tab of the mount cradle. Since the cradle is already

mounted to MA-UMNT-MR-A3 universal mount, guide the AP towards the top tab and insert the top tab into the AP slot.

Then adjust your AP to guide the bottom slot into the cradle’s bottom tab until it clicks into place.

Once in place, the AP should be secured to the cradle by using one of the included screws in the cradle’s bottom tab.

4. Run Ethernet cable(s) to LAN Access ports of your Meraki access point and connect into the appropriate LAN Access port(s). Note some Meraki APs

have 1x LAN port and some have 2x LAN ports. Secure the AP with a Torx security screw.

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco 5400 Manual de usuario

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manual de usuario

Cisco

Cisco RSP7000 Manual de instrucciones

Cisco

Cisco Linksys Business Series Network Storage System... Manual de usuario

Cisco

Cisco CTE 1400 Series Manual de usuario

Cisco

Cisco MGX 8260 Guía de inicio rápido

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Manual del operador

Cisco

Cisco FirePOWER 8000 Series Manual de usuario

Cisco

Cisco IDS 4210 - Intrusion Detection Sys 4210... Manual de usuario

Cisco

Cisco linksys PLTK300 Manual de usuario

Cisco

Cisco ONS 15454 Manual de instrucciones

Cisco

Cisco ASA 5506-X Manual

Cisco

Cisco MX60 Manual de usuario

Cisco

Cisco SCE 1000 and Manual del operador

Cisco

Cisco Network Storage System NSS3000 Series Manual de usuario

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manual de usuario

Cisco

Cisco NCS 1001 Manual

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manual de usuario

Cisco

Cisco ONS 15327 Manual

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco PC4000 Manual de usuario

Cisco

Cisco o UCS X440p Instrucciones de instalación y mantenimiento

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco CX-FEIP-1FX= Installation and con?guration Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario