Cisco ASR 9000 Series Manual de usuario

Replacing Cisco ASR 9000 Series Router

Components

The router is equipped as ordered and is ready for installation and startup when it is shipped. As network

requirements change, you may need to upgrade the system by adding or changing components. This chapter

describes how to maintain router components.

•Prerequisites and Preparation, on page 1

•Replacing the Chassis Air Filter, on page 4

•Removing and Replacing the Fan Trays, on page 10

•Removing and Replacing Power System Components, on page 12

•Removing and Replacing Cards from the Chassis, on page 25

•Migrating from RP1 to RP2 Card, on page 27

•Migrating from RP2 to RP3 Card, on page 30

•Migrating from RSP440 to RSP880 or RSP880-LT Card , on page 33

•Migrating from RSP4-S to RSP880-LT Card (ASR 9906 Router), on page 36

•Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card, on page 38

•Migrating from FC1 to FC2 Card, on page 41

•Migrating from A99-SFC2 to A99-SFC3 Card, on page 41

•Migrating from A99-SFC-S/A99-SFC-T to A99-SFC3-S/A99-SFC3-T Card, on page 42

•Removing a Chassis from the Equipment Rack, on page 43

•Installing a Replacement Chassis in the Equipment Rack, on page 44

•Packing a Chassis for Shipment, on page 44

Prerequisites and Preparation

Before you perform any of the procedures in this chapter, be sure that you:

• Review the b-asr9k-hardware-installation-guide_chapter1.pdf#nameddest=unique_8.

• Read the safety and ESD-prevention guidelines described in b-asr9k-hardware-installation-guide_

chapter1.pdf#nameddest=unique_10.

• Ensure that you have all the necessary tools and equipment before beginning the procedure.

Have access to the safety and compliance document during the installation, see:

http://www.cisco.com/en/US/docs/routers/asr9000/hardware/rcsi/regulatory/compliance/asr9krcsi.html

Replacing Cisco ASR 9000 Series Router Components

Field Replaceable Units

In the Cisco ASR 9006 Router, Cisco ASR 9010 Router, and Cisco ASR 9904 Router, the following components

are field replaceable units (FRU):

• All line cards

• RSP cards

• Power modules

• Fan trays

• Air filters

• Line card and RSP blank fillers

• Compact flash disk

• Gigabit Ethernet small form-factor pluggable (SFP) transceiver modules

• 10-Gigabit Ethernet small form-factor pluggable (SFP+) transceiver modules

• 10-Gigabit Ethernet small form-factor pluggable (XFP) transceiver modules

• Optional card cage doors (Cisco ASR 9010 Router only)

The backplane is not field-replaceable.

Note

In the Cisco ASR 9906 Router, Cisco ASR 9910 Router, Cisco ASR 9912 Router, and Cisco ASR 9922

Router, the following components are FRUs:

• All line cards

• RP cards

• RSP cards (only for Cisco ASR 9906 Router and Cisco ASR 9910 Router)

• Fabric cards

• Power modules

• Fan trays and covers

• Air filters

• Foam media (only for Cisco ASR 9922 Router, Cisco ASR 9912 Router)

• Blank line card fillers

• Gigabit Ethernet small form-factor pluggable (SFP) transceiver modules

• 10-Gigabit Ethernet small form-factor pluggable (SFP+) transceiver modules

• 100-Gigabit Ethernet small form-factor pluggable (CFP) transceiver modules

• Optional card cage doors

Replacing Cisco ASR 9000 Series Router Components

Field Replaceable Units

The backplane, midplane (only for Cisco ASR 9906 Router and Cisco ASR 9910 Router), PEM, and BPID

cards are not FRUs but are field serviceable.

Note

Online Insertion and Removal

Most Cisco ASR 9000 Series Routers FRUs can be removed and replaced with the power on and the system

operating. This is known as online insertion and removal (OIR). Power modules, fan trays, Route Switch

Processor (RSP) cards, Route Processor (RP) cards, Fabric Controller (FC) cards, Line Cards (LCs), shared

port adapter (SPA), and SPA interface processor (SIP) cards all support OIR. Unless otherwise noted, the

maintenance tasks described in this chapter can be performed while the router remains powered on.

Never unplug all the fan trays at the same time.

Caution

Although the power trays are not a true FRU because they do not support OIR, a procedure for replacing the

power trays in Cisco ASR 9000 Series Routers is included in this chapter if a replacement becomes necessary.

Note

OIR Monitoring

The BPID board monitors OIR by counting the number of card insertions for each slot and saving that

information in non-volatile memory. OIR monitoring is done for all fan trays, RSP cards, RP cards, FCs, and

LCs. A card insertion is determined by the CAN Bus Controller (CBC) of the inserted card booting up and

sending a CBC message which is intercepted by the BPID board. Note that a CBC reset or power cycle on a

card will also be interpreted as a card insertion.

A card with an OIR count that exceeds 175 will generate a minor alarm against that slot. If the card OIR count

exceeds 200, a major alarm is generated against that slot. Fan tray insertion counts are not checked against a

threshold. See the Release Notes for Cisco ASR 9000 Series Aggregation Services Routers for Cisco IOS XR

Software Release 3.9.1 for information about CLI commands for obtaining and resetting card insertion data.

Note

Powering Off the Router

Do not turn off the switch on the power tray to remove individual power modules. Power modules support

OIR, so they can be removed and replaced with the power on and the system operating.

Caution

If it becomes necessary to turn all power off to the router, follow these steps:

Replacing Cisco ASR 9000 Series Router Components

Online Insertion and Removal

Procedure

Step 1 Set the power switch on each power tray to the off (0) position.

Step 2 Power off all circuit breakers for the source power lines connected to the power trays.

Step 3 Verify that the Pwr OK indicator on each power module is off.

Step 4 Verify that the OK indicator on the fan tray is off.

Replacing the Chassis Air Filter

The Cisco ASR 9000 Series Routers are equipped with user-replaceable air filters that help prevent dust from

being drawn into the router. One time per month (or more often in dusty environments), examine the air filters

for damage and cleanliness.

In the Cisco ASR 9006 Router, Cisco ASR 9010 Router, Cisco ASR 9904 Router, Cisco ASR 9906 Router,

and Cisco ASR 9910 Router, the chassis air filter is not serviceable. We recommend that you replace the filter

at regular maintenance intervals. The interval may vary between 3 and 12 months depending on the environment.

Note

In the Cisco ASR 9922 Router and Cisco ASR 9912 Router, the three air filters (left, center, and right) contain

foam media which filters the air going into the chassis. The three air filters can be removed from the chassis

so that the foam media (Cisco PIDs 9922-CEN-FLTRMED= and 9922-LR-FLTRMED=) can be replaced on

a regular maintenance interval. The interval may vary between 3 and 12 months depending on the environment.

Note

Damage to the air filter can restrict the airflow, cause overheating in the router, and degrade electromagnetic

interference (EMI) compliance. Be careful when cleaning and replacing the filter.

Caution

This table describes the air filter locations for the Cisco ASR 9000 Series Routers.

Table 1: Air Filter Locations for the Cisco ASR 9000 Series Routers

Air Filter LocationRouter

Located underneath the fan trays.Cisco ASR 9010 Router

Located along the right side of the chassis and is accessible from the rear.Cisco ASR 9006 Router

Single air filter located along the right side of the chassis and is accessible from

the rear.

Cisco ASR 9904 Router

Located underneath the card cage.Cisco ASR 9910 Router

Located underneath the card cage.Cisco ASR 9906 Router

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

Air Filter LocationRouter

Three air filters located on the front of the middle card cage (Figure 5: Cisco

ASR 9922 Router Chassis Air Filters, on page 7).

Cisco ASR 9922 Router

Three air filters on the front of the RP and FC card cage (Figure 7: Cisco ASR

9912 Router Chassis Air Filter , on page 8).

Cisco ASR 9912 Router

Follow these steps to replace an air filter:

Procedure

Step 1 For the Cisco ASR 9006 Router, Cisco ASR 9010 Router, Cisco ASR 9904 Router, Cisco ASR 9906 Router,

and Cisco ASR 9910 Router, choose the procedure for your router:

• For the Cisco ASR 9010 Router, Cisco ASR 9906 Router, and Cisco ASR 9910 Router, remove the air

filter by simply sliding it out of the chassis.

If the accessory grill has been installed on the front of the Cisco ASR 9010 Router, remove it

from the front of the chassis by simply pulling on the grill until it comes loose. See the Installing

Base Chassis Accessories on the Cisco ASR 9010 Router, and Figure 2 for information about

the accessory grill.

Note

Figure 1: Replacing the Cisco ASR 9010 Router Chassis Air Filter

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

Figure 2: Replacing the Cisco ASR 9906 Router Chassis Air Filter

• For the Cisco ASR 9006 Router and Cisco ASR 9904 Router, loosen the thumb screw that secures the

filter to the chassis, and then slide the air filter out of the chassis.

Figure 3: Replacing the Cisco ASR 9006 Router Chassis Air Filter

Thumb screw2Air filter1

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

Figure 4: Replacing the Cisco ASR 9904 Router Chassis Air Filter

Thumb screw2Air filter1

Step 2 For the Cisco ASR 9922 Router and Cisco ASR 9912 Router, remove the three air filters by pulling them off

the front of the chassis (Cisco ASR 9922 Router Chassis Air Filters) and (Cisco ASR 9912 Router Chassis

Air Filter ). Then, for each filter, loosen the thumb screws, rotate the inner frame out, and replace the foam

media (Removing the Cisco ASR 9922 Router Chassis Center Air Filter—Version 1 and Removing the Cisco

ASR 9922 Router Chassis Side Air Filter —Versions 1 and 2).

In the Cisco ASR 9922 Router (version 2 air filter) the center air filter, shown in Cisco ASR 9922

Router Chassis Center Air Filter—Version 2, does not contain replaceable foam media. The left

and right air filters are the same as version 1 and contain replaceable foam media.

Note

Figure 5: Cisco ASR 9922 Router Chassis Air Filters

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

Figure 6: Cisco ASR 9922 Router Chassis Center Air Filter—Version 2

Figure 7: Cisco ASR 9912 Router Chassis Air Filter

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

Figure 8: Removing the Cisco ASR 9922 Router Chassis Center Air Filter—Version 1

Remove foam filter media3Loosen thumb screws1

Rotate and lower inner

frame

Figure 9: Removing the Cisco ASR 9922 Router Chassis Side Air Filter —Versions 1 and 2

Remove foam filter media3Loosen thumb screws1

Rotate and lower inner

frame

Step 3 Visually check the condition of the air filter and/or its foam media to determine whether to install a new

replacement filter or foam media.

Step 4 Install the new air filter.

• For the Cisco ASR 9010 Router, Cisco ASR 9906 Router, and Cisco ASR 9910 Router, slide the new

air filter into the air filter door (honeycomb side up).

Replacing Cisco ASR 9000 Series Router Components

Replacing the Chassis Air Filter

• For the Cisco ASR 9006 Router and Cisco ASR 9904 Router, tighten the thumb screw to secure the filter

to the chassis.

• For the Cisco ASR 9922 Router (version 1 air filter) and Cisco ASR 9912 Router, tighten the thumb

screws that attach the inner frame to the air filter and re-attach the three air filters to the front of the

chassis. For the Cisco ASR 9922 Router (version 2 air filter) tighten the thumb screws that attach the

inner frame to the left and right air filters only. Attach the new center air filter, with arrows pointing

upwards, and re-attach both side filters to the front of the chassis.

For the version 2 air filter on the Cisco ASR 9922 Router, the center does not have thumb screws

because it does not have replaceable foam media.

Note

Align and seat the door carefully to avoid damaging the EMI-preventive gaskets on the door. The

air filter door must be closed and secured at all times to maintain correct EMI performance.

Caution

Removing and Replacing the Fan Trays

Prerequisites

• For the Cisco ASR 9010 Router remove the accessory grill before removing and replacing the fan trays.

• For the Cisco ASR 9906 Router, Cisco ASR 9922 Router and Cisco ASR 9912 Router, remove the fan

tray cover before removing the fan trays for replacement.

Required Tools and Equipment

• 6-inch long number 2 Phillips screwdriver (torque 10 in-lb)

Removing a Fan Tray

Follow these steps to remove and replace the fan trays:

Never unplug all the fan trays at the same time.

Caution

Be sure that the fans have stopped running before removing the fan tray. The fans can take from 3 to 5 seconds

to completely stop running after disengaging the fan tray latch. Handling the fan tray before the fans have

stopped running could cause fingertip injury.

Caution

Replacing Cisco ASR 9000 Series Router Components

Removing and Replacing the Fan Trays

Otros manuales para ASR 9000 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco 3600 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco CSC-C2FCIT Manual de instrucciones

Cisco

Cisco NCS 1001 Manual

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco ONS 15454 Hoja de instrucciones

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manual de usuario

Cisco

Cisco OSM-12CT3/T1 - Optical Services Module... Guía rápida

Cisco

Cisco CE 2000 Platform SCE 2000 4xGBE Manual del operador

Cisco

Cisco NCS 6008 LCC Manual de instrucciones

Cisco

Cisco 220 Series Smart Plus Manual de usuario

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Manual

Cisco

Cisco Aironet 340 Series Manual de usuario

Cisco

Cisco Meraki MX68 Manual

Cisco

Cisco NCS 1001 Guía

Cisco

Cisco SPA901-UK - Small Business Pro Manual de usuario

Cisco

Cisco 7606 Manual de usuario

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Manual de usuario

Cisco

Cisco NCS 1004 Manual de usuario

Cisco

Cisco Prisma EtherLinX Manual de usuario

Cisco

Cisco ONS 15310-CL Manual de usuario

Cisco

Cisco IAD2430 Series Guía de instalación

Cisco

Cisco CWDM-OADM 1 Series Guía de inicio rápido

Cisco

Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control... Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario