Cisco 5400 Manual de instrucciones

Installing and Upgrading FRUs

•Removing and Replacing the Chassis Cover, on page 1

•Replacing the Power Supply, on page 2

•Installing Drive Bays, on page 2

•Upgrading the M.2 Storage Module, on page 3

•Installing and Removing a DIMM, on page 4

•Installing and Removing a NIM, on page 7

Removing and Replacing the Chassis Cover

These are the steps to remove the chassis cover:

1. Confirm the router is turned off and disconnected from the power supply or power supplies.

2. Place the chassis on a flat surface.

3. Remove the screws at top of the chassis cover.

4. Remove the screws at the sides of the device (See Figure 11).

5. Lift the chassis cover once you have removed all the screws.

Figure 1: Removing the Chassis Cover

Installing and Upgrading FRUs

To replace the chassis cover, place the cover evenly on the top of the device and use the screws to secure it

to the device.

Note

Replacing the Power Supply

These are the steps to replace the power supply:

1. Disconnect the power cord from the power supply.

2. Remove the bezel. The bezel is secured with snap latches. To remove the bezel, hold the top and bottom,

and pull the bezel.

3. The latch that secures the power supply to the device is on the right. Press the latch to the left and pull

out the power supply using the handle.

Figure 2: Power Supply Latch and Handle

4. Insert the replacement power supply.

5. Replace the bezel.

Installing Drive Bays

There are two drive bays. You can use one of them, both of them, or none. Refer to Hardware Features -

Replaceable and Upgradable Units to know the types of storage module that each of this bay can hold. If you

had not ordered drives, the slots are closed with a blank cover as shown in the image.

These are the steps to install a drive in a drive bay:

1. The drive bays are in the front panel of the device. The bays are closed with a cover if there are no drives

in the slots.

Installing and Upgrading FRUs

Replacing the Power Supply

2. Press the push button on the center of the cover and pull the cover out of the system to expose the slot.

3. Slide the drive into the slot.

Keep the drive bays covered when there are no drives installed in the slot.

Note

Figure 3: Covers of Hard Disk Drive Slots

Upgrading the M.2 Storage Module

The M.2 storage module is a hardware that is 22mm wide and 80mm long. This hardware comes with different

storage capacities.

These are the steps to upgrade the M.2 memory module:

1. Remove the chassis cover.

2. Locate the M.2 storage module. Refer to the Chassis - Internal View section to identify and locate the

module.

3. Remove the old storage module by unscrewing the screw that secures the hardware and removing out the

storage module.

4. Plug in the new storage module in the same location and secure it with the screw.

Installing and Upgrading FRUs

Upgrading the M.2 Storage Module

Figure 4: Upgrading the M.2 Storage Module

5. Replace the chassis cover.

Installing and Removing a DIMM

There are two DDR4 DIMM slots. DIMMs have a polarization notch on the connecting edge to prevent

incorrect insertion.

Figure 5: DIMM Showing Polarization Notch

These are the steps to install a DIMM:

1. Remove the chassis cover.

2. Locate the DIMM module on the device.

Installing and Upgrading FRUs

Installing and Removing a DIMM

Figure 6: DIMM Module

3. Make sure that both latches on the DIMM connector are in the open position.

4. Orient the DIMM so that the polarization notch lines up with the polarization key on the connector.

5. Insert the DIMM into the connector.

Installing and Upgrading FRUs

Installing and Removing a DIMM

Figure 7: Inserting a DIMM

6. Replace the chassis cover.

These are the steps to remove a DIMM:

1. Remove the chassis cover.

2. Locate the DIMM module on the device. Refer to the Chassis - Internal View section to identify and locate

the DIMM module.

3. Pull the latches away from the DIMM at both ends to lift the DIMM slightly. Pull the DIMM out of the

socket.

Figure 8: Removing a DIMM

4. Place the DIMM in an antistatic bag to protect it from ESD damage.

5. Replace the chassis cover.

Installing and Upgrading FRUs

Installing and Removing a DIMM

Installing and Removing a NIM

These are the steps to install a NIM:

• Locate the NIM slot on the front panel.

• Loosen the screws to open the slot cover.

• Insert the NIM into the slot.

• Tighten the screws to secure the NIM in the slot.

These are the steps to remove a NIM:

• If the NIM is up and running, issue the following command to shut down the NIM gracefully before

removing it:

hw-module subslot slot 0/2 stop

If you do not shut down the NIM gracefully before removing it, the NIM card

could get damaged.

Caution

• Locate the NIM slot on the front panel.

• Loosen the screws that secure the NIM.

• Gently pull out the NIM from the slot.

ENCS supports hot swap or OIR (Online Insertion and Removal) for NIM. So, you can insert and remove the

NIM when ENCS is running; however, before removing the NIM, ensure that the NIM is shut down gracefully.

Code extract that shows the graceful shutdown of a NIM:

CSR-8#hw-module subslot 0/2 stop

Proceed with stop of module? [confirm]

CSR-8#

CSR-8#sh platform

Chassis type: ISRV

Slot Type State Insert time (ago)

--------- ------------------- --------------------- -----------------

0 ISRV ok 16:41:27

0/2 NIM-4G-LTE-NA stopped 00:00:05

R0 ISRV ok, active 16:42:19

F0 ISRV ok, active 16:42:19

Installing and Upgrading FRUs

Installing and Removing a NIM

Installing and Upgrading FRUs

Installing and Removing a NIM

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Manual de usuario

Cisco

Cisco ONS 15310-MA SDH Manual

Cisco

Cisco Mc3810 - 16MB Flash Memory Guía rápida

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Manual del operador

Cisco

Cisco NSS2000 Series Manual de usuario

Cisco

Cisco NCS 1004 Manual de usuario

Cisco

Cisco S170 Web Manual de usuario

Cisco

Cisco Linksys NSLU2 Manual de usuario

Cisco

Cisco WEC600N Manual de usuario

Cisco

Cisco ONS 15540 ESP Manual

Cisco

Cisco NCS 4206 Manual de instrucciones

Cisco

Cisco CVPN3015-NR - VPN Concentrator 3015 Manual de usuario

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manual de usuario

Cisco

Cisco Wide Area Application Engine 612 Manual

Cisco

Cisco CPS-MSP-1RU-K9 Manual de usuario

Cisco

Cisco SA520-K9 - SA 500 Series Security Appliances Manual de usuario

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco IPS 7.1 Manual de usuario

Cisco

Cisco CTM GateWay Guía de instalación

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manual de usuario

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco NCS 1010 Hoja de instrucciones

Cisco

Cisco 40-Gigabit and 100-Gigabit CFP Transceiver... Guía de inicio rápido

Cisco

Cisco ONS 15454 Manual de instrucciones

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario