Cisco DATAVOX 7941 Manual de usuario

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Requirements

■

2.1 Identifying phone model

■

2.2 Phone firmware

■

2.3 DHCP server

■

2.4 PBXware version

■

3 Installation

■

3.1 Power adapter

■

3.2 Reset to factory settings

■

4 Registering Phone

■

4.1 Manual Configuration

■

4.2 Auto Provisioning Configuration

■

Introduction

This "How to" is written as general guide on how to use Cisco 7941 with PBXware using SIP 7.1

Cisco 7941 firmware. It covers the most common tasks that are required to have your Cisco

7941 working efficiently.

Requirements

Identifying phone model

To start and successfully complete registration of your Cisco phone you need to know which

phone model you will setup.

On the front of each Cisco phone there are exact model information that you should check.

Although different phone models can have exactly the same requirements and installation

procedure, phone models can also have significantly different requirements and installation

procedure, so that ignorance of your own model may result in the inability to successfully set up

your phone.

Phone firmware

Make sure that device is loaded with firmware (Application Load ID) 7.X or 8.X.

Press the Settings button.

■

Scroll to Status and press the select button.

■

Scroll to Firmware Versions and press the select button.

■

The firmware is listed under Application Load ID.

■

DHCP server

Fully configured and operational DHCP server.

PBXware version

In order to find out the PBXware version, please login to PBXware and navigate to Settings:

About. On the top of About page is a code similar to this one "PBXware Edition: Business,

Release: 3.1 (041373f), Running: 1.4.24-gc-75ee203", where "Release" denotes the exact version

of your PBXware.

Installation

This chapter describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power adapter

■

Factory settings

■

Power adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

Reset to factory settings

This step is not required for out-of-the-box phones, however, if the phone has been already used

then it is a must.

Unplug the power cable from the phone.

■

Hold down the # key, and then plug the power cable in again. The phone should begin its

■

power up cycle.

Release the # key after the Speaker button is no longer lit. You should this message displayed

■

on the phone: Reset key sequence detected

Press 123456789*0# (or in some cases this sequence is 3491672850*# ) within 60 seconds

■

after the Headset, Mute, and Speaker buttons begin to flash.

-If you fail to complete this key sequence or do not press any keys, the Headset, Mute, and

Speaker buttons will stop flashing after 60 seconds and the phone will continue with its normal

start-up process. The phone will not reset.

-If you enter an invalid key sequence, the buttons will stop flashing immediately and the phone

will continue with its normal start-up process. The phone will not reset.

If you enter this key sequence correctly, the phone displays this prompt:

■

Keep network cfg? 1 = yes 2 = no

-To maintain existing network configuration settings for the phone when the phone resets, press

-To reset network configuration settings when the phone resets, press 2.

-If you press another key or do not respond to this prompt within 60 seconds, the phone will

continue with its normal start-up process and will not reset.

Registering Phone

Manual Configuration

UAD Settings

STEP ONE: PBXware IP address.

1. Find out the IP address of PBXware server.

STEP TWO: Login to PBXware.

1. Open a new browser window and enter the IP address to access the PBXware administration

interface login screen.

Example: http://192.168.1.2

2. Hit "Enter" on your keyboard.

3. Login to PBXware with your e-mail address and password.

STEP THREE: UAD status.

1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click

on the "edit" icon corresponding to "Cisco 7941".

2. Make sure the "Status" is set to "active", "Auto provisioning" is set to "No" and "DHCP" is set

to "Yes".

3. Click on the "Save" button to save changes.

Creating Extension

STEP ONE: Add Extension.

1. Navigate to "Extensions". Click on "Add Extension".

2. The standard options window will be shown below.

Creating

Extension/Extensions Add

3. Select Cisco 7941 from "UAD" select box.

4. Select Location: "Local" or "Remote".

Note:

-"Local" is for all extensions registered on LAN.

-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.

Creating

Extension/Extensions Add

5. Click on the "Next" button.

STEP TWO: Extension values.

1. Enter values into the required field text boxes.

REQUIRED FIELDS:

Name:

Enter a name for the extension being created. Example: John Smith.

E-mail:

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected].

Creating

Extension/Extensions Add

an example with details filled in

2. Click on the "Save" button.

Creating

Extension/Extensions Edit

an example with details filled in

3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address

associated with this extension.

OPTIONAL FIELDS:

Extension:

An auto-generated extension number based on the next available sequential number. An

extension value can be changed. Example: 1000.

Username:

Username is auto generated/populated and cannot be changed since it allows the system to use

this value for other important operations.

Secret:

A secret value associated with the UAD is auto-generated in order to allow the UAD to

successfully register with the system. The secret value can be changed.

PIN:

An auto-generated PIN will allow access to voicemail and online self care.

Registering Phone

STEP ONE: Electricity and Ethernet.

- Plug the power adapter into a power jack then connect it to the electricity network.

- Connect ethernet port to a hub, router or switch as to access LAN.

After successfully connecting the Cisco 7941 to the electricity and data networks, it is time to

STEP TWO: Cisco 7941 settings configuration.

Unlock configuration:

1. Press the "settings" button.

2. Use the "navigation" button and navigate down to "Unlock Config".

3. Press the "Select" button.

4. Enter password (Default factory password is "cisco").

5. Press the "Accept" button to unlock configuration.

SIP Configuration

1. Using the "navigation" button navigate up to "SIP Configuration".

2. Press the "Select" button.

3. Press the "Select" button to enter into "Line 1 Settings".

4. Enter details into:

REQUIRED FIELDS:

Name

Cisco 7941 extension number. Example: 1000.

Authentication Name

Usually the same number as "Name".

Authentication Password

The Secret of the extension as received in the e-mail associated with this extension. Example:

3dX3r5

Proxy Address

IP address of PBXware server. Example: 192.168.1.2

OPTIONAL FIELDS

Shortname

Example: John Smith, Reception, Entrance Main, Agent One etc.

Display Name

Example: John Smith, Reception, Entrance Main, Agent One etc.

Proxy Port

By default 5060

5. Press accept button and reboot Cisco 7941.

- Conclusion: If everything is done as above described you should have successfully registered

your Cisco 7941 to PBXware. Dial *123 to verify registration.

- For further information, please contact the manufacturer or check their web site

www.cisco.com.

Auto Provisioning Configuration

UAD Settings

STEP ONE: PBXware IP address.

1. Find out the IP address of PBXware server.

STEP TWO: Login into PBXware.

1. Open a new browser window and enter the IP address to access the PBXware administration

interface login screen.

Example: http://192.168.1.2

an example with IP address

2. Hit "Enter" on your keyboard.

3. Login to PBXware with your e-mail address and password.

STEP THREE: UAD status.

1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click

on the "edit" icon corresponding to "Cisco 7941".

2. Make sure "Status" is set to "active", "Auto provisioning" is set to "Yes" and "DHCP" is set to

"Yes".

3. Click on the "Save" button to save changes.

Creating Extension

STEP ONE: Add Extension.

1. Navigate to "Extensions". Click on "Add Extension".

2. The standard options window will be shown below.

Creating

Extension/Extensions Add

3. Select Cisco 7941 from "UAD" select box.

4. Select Location: "Local" or "Remote".

Note:

-"Local" is for all extensions registered on LAN.

-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.

Creating

Extension/Extensions Add

5. Click on "Next" button.

STEP TWO: Extension values.

1. Enter values into required field text boxes.

REQUIRED FIELDS:

Name:

Enter a name for the extension being created. Example: John Smith.

E-mail:

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Auto provisioning:

Set to "Yes".

MAC Address:

Cisco 7941 MAC address. Example: 001646f5f797

Creating

Extension/Extensions Add

an example with details filled in

2. Click on the "Save" button.

Creating Extension

an example with details filled in

3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address

associated with this extension. OPTIONAL FIELDS:

Extension:

An auto-generated extension number based on the next available sequential number. An

extension value can be changed. Example: 1000.

Username:

Username is auto generated/populated and cannot be changed since it allows the system to use

this value for other important operations.

Secret:

A secret value associated with the UAD is auto-generated in order to allow the UAD to

successfully register with the system. The secret value can be changed.

PIN:

An auto-generated PIN will allow access to voicemail and online self care.

Registering Phone

STEP ONE: Electricity and Ethernet.

- Plug the power adapter into a power jack then connect it to the electricity network.

- Connect the ethernet port to a hub, router or switch as to access LAN.

"TFTP Server" must be set with TFTP server value.

STEP TWO: Cisco 7941 TFTP configuration.

Otros manuales para DATAVOX 7941

Tabla de contenidos

Otros manuales de Teléfono IP de Cisco

Cisco

Cisco 8800 Series Manual de usuario

Cisco

Cisco Vodafone One Net 7841 Manual de usuario

Cisco

Cisco 7961 Manual de usuario

Cisco

Cisco 7942 Manual de usuario

Cisco

Cisco 7800 Series Manual de usuario

Cisco

Cisco MCS 7800 Series Manual de usuario

Cisco

Cisco Unified 8961 Manual de usuario

Cisco

Cisco 6945 Series Manual de usuario

Cisco

Cisco 7910 - IP Phone VoIP Manual de usuario

Cisco

Cisco 8841 Manual de usuario

Cisco

Cisco Cisco 7940 Manual de usuario

Cisco

Cisco 7811 Manual de usuario

Cisco

Cisco Unified 7905G Manual de servicio

Cisco

Cisco SPA 303 Series Manual de usuario

Cisco

Cisco 7941G - Unified IP Phone VoIP Manual de usuario

Cisco

Cisco 7920 - Unified Wireless IP Phone VoIP Manual de usuario

Cisco

Cisco 8941 Manual de usuario

Cisco

Cisco Unified 7912G Manual de usuario

Cisco

Cisco 7962 Manual de usuario

Cisco

Cisco Cisco 7960 Manual de servicio

Cisco

Cisco 7841 Manual de usuario

Cisco

Cisco 7800 Series Manual de usuario

Cisco

Cisco 7821 Manual de usuario

Cisco

Cisco 7931G - Unified IP Phone VoIP Manual de instrucciones

Manuales populares de Teléfono IP de otras marcas

Alcatel

Alcatel 4028 Manual de usuario

Polycom

Polycom Polycom VVX 600 Manual de usuario

Polycom

Polycom SoundPoint IP 450 Manual de usuario

Polycom

Polycom SoundPoint IP 650 Manual de usuario

Proximus

Proximus Maestro 3016 IP Manual de usuario

Fanvil

Fanvil X4 Manual de usuario

Snom

Snom 320 Manual de usuario

Yealink

Yealink Yealink SIP-T46G Manual de usuario

Avaya

Avaya 4625SW Manual de usuario

Yealink

Yealink SIP-T52S Manual de usuario

Nortel

Nortel 1140E Manual de usuario

Nexotek

Nexotek NT-P500 Manual de usuario

Avaya

Avaya Integral 5 R3.0 Manual de usuario

GE 28320EE2 - Dect 6.0 InfoLink 2 Manual de usuario

Avaya

Avaya 4600 Series Manual de servicio

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manual de usuario

Nortel

Nortel i2050 Manual de usuario

Fiberme

Fiberme FAP260 Series Manual de usuario