Cisco AS5400 Series Manual de usuario

Quick Start Guide

Cisco AS5350 and Cisco AS5400 Universal Gateways

1Documents, Equipment, and Tools

2Install Chassis

3Install Modules

4Connect Cables

5Power Up the Universal Gateway

6Perform Initial Configuration

7Slot Numbering

8Obtaining Documentation

9Obtaining Technical Assistance

10 Obtaining Additional Publications and Information

1 Documents, Equipment, and Tools

User Documentation

All of the documents described here are available on line and on the documentation CD-ROM that you received with your

universal gateway. To be sure of obtaining the latest information, you should access the online documentation.

Note The information in this document applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal

gateways.

To access online user documentation:

From Cisco.com at http://www.cisco.com, under Service & Support, select Technical Documents and select Cisco Product

Documentation.

To access user documentation on the Documentation CD-ROM:

On the Documentation CD-ROM, select Cisco Product Documentation.

Paths to specific documents are provided below, starting at Cisco Product Documentation.

Tip To navigate up to the next higher level in the documentation hierarchy, click on CONTENTS in the navigation bar at

the top of each page.

Cisco AS5350 and Cisco AS5400 Universal Gateway Documentation

Regulatory Compliance and Safety Information

The Regulatory Compliance and Safety Information document provides essential safety information applicable to your universal

gateway. A printed copy of this document is shipped with this device.

You can access this document at Cisco Product Documentation > Access Servers and Routers > Access Servers> Cisco AS5350

or Cisco AS5400> Regulatory Compliance and Safety Info for the Cisco AS5350 or Cisco AS5400.

Hardware Installation

The hardware installation guide provides additional detailed description, installation, and cabling information.

You can access this document at Cisco Product Documentation > Access Servers and Routers > Access Servers > Cisco AS5350

or Cisco AS5400 > Hardware Installation Documents for Cisco AS5350 or Cisco AS5400.

Software Configuration

The software configuration guide provides additional detailed configuration information.

You can access this document at Cisco Product Documentation > Access Servers and Routers > Access Servers> Cisco AS5350

or Cisco AS5400 > Software Configuration Documents for Cisco AS5350 or Cisco AS5400.

Release Notes

Cisco IOS release notes for the Cisco AS5350 and Cisco AS5400 universal gateways provide up-to-date information about

specific Cisco IOS software releases and new hardware used on these universal gateways.

You can access these documents at Cisco Product Documentation > Access Servers and Routers > Access Servers> Cisco AS5350

or Cisco AS5400 > Cisco IOS Release Notes for Cisco AS5350 or Cisco AS5400.

Related Hardware Documentation

Replacing the Power Supply in the Cisco AS5300 Series and Cisco AS5400 has instructions about replacing the power supply.

You can access this document at Cisco Product Documentation > Access Servers and Routers > Access Servers > Cisco AS5350

or Cisco AS5400 > Hardware installation documents for Cisco AS5350.

Cisco IOS Software Documentation

Master Index to Software Documentation

The master index provides links to topics and commands for specific Cisco IOS software releases.

You can access these documents at Cisco Product Documentation > Cisco IOS Software >

Cisco IOS Software Release you are using > Master index for Cisco IOS software release you are using.

Configuration Guides

The Cisco IOS software configuration guides provide detailed configuration procedures and examples.

You can access these documents at Cisco Product Documentation > Cisco IOS Software > Cisco IOS Software Release you are

using > Configuration Guides and Command References > Configuration guide for your application.

Command References

The Cisco IOS software command references provide detailed information about each command.

You can access these documents at Cisco Product Documentation > Cisco IOS Software > Cisco IOS Software Release you are

using > Configuration Guides and Command References > Command reference for your application.

New Feature Documentation

New Feature Documentation contains detailed information about new features introduced in specific Cisco IOS releases.

You can access these documents at Cisco Product Documentation > Cisco IOS Software > Cisco IOS Software Release you are

using > New Feature Documentation.

If you have an account on Cisco.com, you can get updated information about platform support for features by accessing Feature

Navigator at the following URL:

http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp

Release Notes

Cisco IOS release notes for all platforms provide up-to-date information about specific Cisco IOS software releases.

You can access these documents at Cisco Product Documentation > Cisco IOS Software > Cisco IOS Software Release you are

using > Release Notes > Release Notes for the Cisco IOS software release you are using.

Supporting Documents and Related Documentation

These documents contain additional information, including debug commands and error messages, about specific Cisco IOS

software releases.

You can access these documents at Cisco Product Documentation > Cisco IOS Software > Cisco IOS Software Release you are

using > Supporting Documents or Related Documentation.

Additional documents of this type are located at Cisco Product Documentation > Access Servers and Access Routers >

Access Servers > Cisco AS5350 or Cisco AS5400.

Items Included with Cisco AS5350 and Cisco AS5400 Universal Gateways

•19- and 24-inch rack-mount kits

•Rubber feet for desktop installation

•RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL)

•RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL)

•RJ-45-to-DB-25 male DCE adapter (labeled MODEM)

•RJ-45-to-RJ-45 rollover console cable

•ESD-preventive wrist strap

•Nylon cable ties

•Cable tie holder

•Grounding lug

•Cisco Information and CD-ROM Package

Items Not Included

Individual items in this list may be required for your particular application:

•Straight-through RJ-45-to-RJ-45 cable for an Ethernet connection

•Straight-through RJ-45-to-RJ-45 cables for T1 connections

•E1 cables for E1 connections

•Ethernet hub or PC with a network interface card for Ethernet LAN connections

•PC running terminal emulation software for local administrative access

•Modem for remote administrative access

•One breakout cable consisting of a 36-pin connector connected to eight RJ-45 adapters for CT1/CE1 connections

•75-ohm coaxial cable for a CT3 connection

2 Install Chassis

Note The information in this document applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal

gateways.

Note Unless specifically noted, all references to the Cisco AS5400 also apply to the Cisco AS5400HPX.

Safety Information

Warning

For safety information you need to know before working on your Cisco universal gateway, see the Regulatory

Compliance and Safety Information document that accompanied this device.

Setting Up the Chassis

You can install the chassis in a rack or set it on a desktop. Select the procedure that best meets the needs of your network:

•Rack-Mounting the Chassis, page 5

•Desktop Installation, page 7

Warning

This unit is intended for installation in restricted access areas. A restricted access area is where access can only

be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is

controlled by the authority responsible for the location. To see translations of the warnings that appear in this

publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Rack-Mounting the Chassis

This section describes how to rack-mount the chassis. The universal gateway arrives with 19-inch rack-mount brackets and

larger brackets for use with a 23- or 24-inch rack.

Cisco AS5350 Rack-Mount Brackets

Cisco AS5400 Rack-Mount Brackets

The following information will help you plan your equipment rack configuration:

•Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each unit generates heat. An

enclosed rack should have louvered sides and a fan to provide cooling air. Heat generated by equipment near the bottom of

the rack can be drawn upward into the intake ports of the equipment above.

•When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or exhaust ports. If the

chassis is installed on slides, check the position of the chassis when it is seated in the rack.

•Baffles can isolate exhaust air from intake air, which also helps to draw cooling air through the chassis. The best placement

of the baffles depends on the airflow patterns in the rack, which can be found by experimenting with different

configurations.

•When equipment installed in a rack (particularly in an enclosed rack) fails, try operating the equipment by itself, if possible.

Power off other equipment in the rack (and in adjacent racks) to allow the unit under test a maximum of cooling air and

clean power.

•Install the chassis and external devices to which it will connect in a contiguous stack.

36012

Bracket for 23-inch rackBracket for 19-inch rack

H6028

Bracket for 23- or 24-inch rackBracket for 19-inch rack

Required Tools and Equipment

You need the following tools and equipment to rack-mount the chassis:

•Number 2 Phillips screwdriver (not included)

•Medium flat-blade screwdriver (not included)

•Screws for attaching the chassis to the rack (not included)

•Standard rack-mount brackets (included)

•Screws for attaching the brackets to the chassis (included)

Attaching Brackets

Attach the mounting brackets to the chassis as shown, using the screws provided. Attach the second bracket to the opposite side

of the chassis.

Note The chassis may be installed with either the front or rear panel facing forward.

Cisco AS5350 Bracket Installation—Front Panel Forward (19-Inch Rack)

Cisco AS5400 Bracket Installation—Front Panel Forward (19-Inch Rack)

35669

Note: The second bracket attaches to the other side of the chassis.

The chassis can also be installed with the rear panel forward.

H10643

Installation in a Rack

Install the chassis in the rack. Rack-mounting screws are not provided. Use two screws for each side (supplied with the rack).

Installing the Cisco AS5350 in a Rack (19-Inch Rack)

Installing the Cisco AS5400 in a Rack (19-Inch Rack)

Desktop Installation

For desktop or shelf mounting, use the rubber “feet” shipped on a black adhesive strip with the chassis. They protect the chassis

and provide a nonskid surface.

The location of the chassis is extremely important for proper operation. Equipment placed too close together, inadequate

ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. The following

information will help you to plan the location of the chassis:

•Plan for access to both front and rear panels of the chassis.

•Ensure that the room where the chassis operates has adequate ventilation. Remember that electrical equipment generates

heat. Ambient air temperature may not cool equipment to acceptable operating temperatures without adequate ventilation

To attach the rubber feet, take the following steps:

Step 1 Locate the rubber feet that shipped with the chassis.

Step 2 Place the universal gateway upside-down on a smooth, flat surface.

35659

Note: The second bracket attaches to the rack at the other side

of the chassis. The chassis can also be installed with the

front panel forward.

29034

Note: The second bracket attaches to the rack at the other side

of the chassis. The brackets can also be installed with the

front panel forward.

Step 3 Peel the rubber feet off the black adhesive strip and place them adhesive-side down at each corner of the underside of

the chassis.

Step 4 Place the universal gateway top-side up on a flat, smooth, secure surface.

Caution Do not place anything on top of the universal gateway that weighs more than 10 lb (4.5 kg). Excessive weight on

top could damage the chassis.

Chassis Ground Connection

You must connect the chassis to a reliable earth ground using the ground lug (provided) and size AWG 6 (13 mm2) wire.

To attach the chassis ground, take the following steps:

Step 1 Strip one end of the ground wire to expose approximately 0.75 in. (20 mm) of conductor.

Step 2 Crimp the ground wire to the ground lug, using a crimp tool of the appropriate size.

Step 3 Attach the ground lug to the chassis. Use a medium flat-blade screwdriver and the screws supplied with the ground lug.

Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).

Step 4 Connect the other end of the ground wire to a suitable grounding point at your site.

Cisco AS5350 Ground Lug Attachment

Cisco AS5400 Ground Lug Attachment

82735

Ground lug

attachment

82734

Ground lug

attachment

3 Install Modules

Note The information in this document applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal

gateways.

Note Unless specifically noted, all references to the Cisco AS5400 also apply to the Cisco AS5400HPX.

Note Cisco AS5350 and Cisco AS5400 come with carrier cards and DFCs already installed. If the required dial feature cards

are already installed, proceed to the “Connect Cables” section on page 14.

For additional information about installing carrier cards and dial feature cards, refer to the Cisco AS5350 and Cisco AS5400

Universal Gateway Card Installation Guide.

You can access this document at Cisco Product Documentation > Access Servers and Access Routers > Access Servers >

Cisco AS5350 or Cisco AS5400 > Hardware Installation Documents for Cisco AS5350 or Cisco AS5400.

Installing Carrier Cards

Caution The carrier cards that carry the DFCs are not hot swappable. Removing a carrier card while the system is still

powered on may cause permanent damage to electronic circuits on the card.

Warning

Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network

voltages. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance

and Safety Information document that accompanied this device.

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity. To see translations

of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information

document that accompanied this device.

Installing a Carrier Card

If you need to install a carrier card, follow this procedure:

Step 1 Make sure the chassis is powered off.

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the

power at the circuit breaker on DC units. To see translations of the warnings that appear in this publication, refer

to the Regulatory Compliance and Safety Information document that accompanied this device.

Step 2 Attach an ESD-preventive wrist strap.

Step 3 Slide the carrier card into the slot until it touches the backplane connector.

Install the Carrier Card in the Cisco AS5350

Install the Carrier Card in the Cisco AS5400

Step 4 Align the captive screws with their holes, and seat the card completely.

Step 5 Tighten the two captive screws to secure the carrier card to the chassis.

Tighten the Captive Screws on the Cisco AS5350

Tighten the Captive Screws on the Cisco AS5400

36004

37161

36005

Captive screw

37162

Captive

screw Captive

screw

Otros manuales para AS5400 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Puerta de Cisco

Cisco

Cisco ACE XML Gateway Manual de usuario

Cisco

Cisco Expressway CE1000 Appliance Manual de usuario

Cisco

Cisco 3521 Manual de servicio

Cisco

Cisco ASR 9000 Series Manual de usuario

Cisco

Cisco DPQ2425 Manual de usuario

Cisco

Cisco LINKSYS RFC 2364 Manual de usuario

Cisco

Cisco DPC2425 Manual de usuario

Cisco

Cisco Intelligent Wireless Access Gateway Manual de usuario

Cisco

Cisco VG204 Manual de usuario

Cisco

Cisco Linksys WAG325N Manual de usuario

Cisco

Cisco T3 Manual de usuario

Cisco

Cisco ASR 5000 Series Manual de instrucciones

Cisco

Cisco TELEPRESENCE ISDN GATEWAYS 2.0 Guía de referencia

Cisco

Cisco 2650XM Instrucciones de instalación y funcionamiento

Cisco

Cisco VGD-1T3 Manual de usuario

Cisco

Cisco VG202 Manual de usuario

Cisco

Cisco Linksys WAG310G Manual de usuario

Cisco

Cisco DPC3827 Manual de usuario

Cisco

Cisco SPA8000-G1 Manual de usuario

Cisco

Cisco DPC3825 Manual de usuario

Cisco

Cisco IR510 Manual

Cisco

Cisco EPC3928 DOCSIS Manual de usuario

Cisco

Cisco AS5400XM Instrucciones originales

Cisco

Cisco EPC2425 Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario