Cisco TelePresence SX10 Manual de usuario
August 2019
Search Method
Cisco SX10, SX20
User
Guide
To turn on the system, press the ‘Power’ button on the remote control.
Ensure Cisco system white light is on.
To wake up the Telehealth system, press any button on the remote.
If the systems does not turn on/wake, ensure the TV is on the
appropriate input.
If you see the system name appear at the top of the screen the system is
online.
If you see ‘No Network Connection’ at the top of the screen the system
is offline. Please contact your regional technical support to resolve any
connectivity issues.
Turning On/Waking up theTelehealthSystem
1. Decrease/Increase volume.
2. Parameter keys which move the cursor
left/right/up/down.
3. OK/Enter.
4. Go back one step.
5. Microphone mute/unmute.
6. Go back/Call button/Accept incoming call.
7. Reject incoming call/End call/Cancel/Go back
to Home screen.
8. Keypad: used to dial.
1. The ‘Settings’ icon provides access to Standby mode,
System Information and the Do Not Disturb feature. When
set to ‘Do Not Disturb,' ringtones and call attempts made
by others to reach you will appear as missed calls. You
may, however, place a call. While in ‘Do Not Disturb,’ the
system will return to normal operation after 60 minutes.
2. The ‘Call’ icon is located to the left in the lower part of
the display.
3. The ‘Share Content’ icon is located to the right in the
lower part of the display.
4. The ‘Camera Control’ menu is located in the upper right
corner of the display.
If someone calls you, you may accept or decline the call. If you
decline the call, a message stating that the unit is busy will be
sent to the caller.You may also use the call keys located
below the circular buttons on the remote control to
accept/decline a call (green=accept, red=decline).
The Remote
The Home Screen
Receiving a Call
August 2019
Placing a Call
A.Select ‘Call’ and press ‘OK’ on the remote
control or press the green ‘Call’ button on the
remote control.
1. Placing a call using ‘Search or Dial’
C.To enter the dialing address, press the
corresponding keys on the remote control. To
invoke the virtual keyboard, use the left arrow
cursor key on the remote control. You may now
move about the virtual keyboard and select
characters. Press ‘OK’ to select a character. To
access numbers click ‘123’ and then ‘OK.’
D.Once your dialing address has been
entered, press the green ‘Call’ button to
place the call.
B. Use the up Cursor key to select the
‘Search or Dial’ field at the top of the
menu. Press ‘OK.’
2.Placing a call from ‘Contacts,’ ‘Favorites’ or the ‘Directory’
A.Select ‘Call’ and press ‘OK’ on the remote control or
press the green ‘Call’ button on the remote control.
B.When the contact list appears, use the
horizontal cursorkeys on the remote control
to go between 'Favorites', 'Recents' and
‘Directory’ (horizontally) and then down in
one of the lists.
C.Once an entry has been
located, press ‘OK’ on the
remote control to invoke the
‘Call’ menu.
D.Narrow down your search by typing the
part or all of the system name or location in
the ‘Search or Call’ bar.
E.Then press ‘OK’ or the green ‘Call’ button
on the remote control to place the call.
Favorites: contacts that have been saved by you. This list includes contacts you call frequently.
Directory: contacts from all Regional Health Authorities and NLCHI.
Recents: list of calls you have previously placed, received or missed.
August 2019
Changing Call Display Options
A.Go to the camera icon in the top right
corner of the screen and press ‘OK.’
A.Navigate to ‘Layout’ in the upper right
corner and press ‘OK’ on the remote control.
The icon below will appear only when relevant.
1.Self View
B.Select the push pin icon and press ‘OK.’To
turn off self-view press ‘OK’ on the push pin
again.
C.To change the position of the self-view
window, go to the ‘Layout’ icon in the top
left corner of the screen and press ‘OK.’
D.The layout menu will now appear. Press the
down arrow on the remote control to navigate to
the self-view image.
E.The self-view image will now turn blue to
show that it has been selected. Click ‘OK’ on
the remote control. Arrows will now appear to
indicate that the self-view image can be
moved. Possible new locations are indicated.
F.Use the arrow keys on the remote control to
move the image and press ‘OK’ when finished.
2.Change Call Layout
B.Use the horizontal arrow keys on the remote
control to move horizontally to the new layout
you would like to use and press ‘OK’ to select a
layout.
August 2019
i.While on a call or not on a call (as shown here),
move the cursor up to the upper right corner to the
‘Camera’ icon. Press ‘OK’ on the remote control.
3. Camera Control
iii.You may now adjust the pan, zoom and tilt of the
camera. Use ‘Increase’/ ‘Decrease’ controls on the remote
control to adjust the zoom and the cursor controls to
adjust the pan and tilt. Press ‘Back’ to exit the menu.
While on a call, there may be capability to control the camera on both sides of the call. Camera control
on your side of the call is called ‘Near End’ and on the other side of the call is called ‘Far End.’
A. Near End Camera Control
ii.The ‘Camera’ icon will now appear. Press ‘OK’
again on the remote control.
B. Far End Camera Control
i.Navigate to ‘Participants’ in the upper right
corner and press ‘OK’ on the remote control. A
list of the participants will then appear.
ii.A menu showing a list of the participants on
the call will now appear. Navigate to the
participant whose camera you want to control
and press ‘OK’ on the remote control.
A submenu will now appear.
Note: if you select ‘Drop’ that participant will
be disconnected from the call.
iii.To control the far end camera, navigate to
‘Camera’ and click ‘OK’ on the remote control.
iv.Adjust the pan, tilt and zoom and use ‘OK’
or ‘Back’ on the remote control to exit.
August 2019
Changing Call Audio Options
A.To adjust the volume, use the ‘+/-‘ button at the top of
the remote control.Ensure the TV volume is appropriate
using the TV remote control.
Note: You cannot adjust the volume while adjusting
camera control.
B.To mute the microphone so that others cannot hear you,
press the mute button on the remote control or microphone
itself. The button on the microphone will be red when
muted.
Press either button again to unmute. The microphone
button will be green when unmuted.
Note: Other participants cannot hear you while you are
muted, they are still able to see you.
Sharing Content
A.During a Telehealth call you may want to share a
document or presentation. To do this, make sure your
presentation/documentation source is connected and on.
You may need to select ‘Share’ (located in the center
bottom of the screen, if it appears) and press ‘OK’ on the
top remote control.
B.Your source will now be shared.
C. The size of the shared images is controlled by means
of the ‘Minimize/Maximize’ field which appears along the
bottom of the display (number two from the left). Select
this and press ‘OK’ on the remote control, if needed.
D.To stop sharing content, select ‘Stop sharing’
(which appears along the bottom of the display,
number one from the left) and press ‘OK’ on the
remote control.
Ending The Call
To leave or end the call, press the red ‘End Call’ button on the
remote control or use the cursor keys to select ‘End’ and then press
‘OK’ to end the call.
If you have technical difficulties with your call, please contact your regional help desk.
Otros manuales para TelePresence SX10
21
Este manual sirve para los siguientes modelos
1
Otros manuales de Sistema de conferencias de Cisco
Cisco
Cisco Codec C Series Manual de usuario
Cisco
Cisco IP Conference Station 7935 Manual de usuario
Cisco
Cisco Service Manual Manual de usuario
Cisco
Cisco DX650 Manual de usuario
Cisco
Cisco TelePresence System C20 Plus Manual de usuario
Cisco
Cisco TelePresence Codec C-series Manual de usuario
Cisco
Cisco CTS 1000 - TelePresence System 1000 Video... Manual de instrucciones
Cisco
Cisco Desk Manual de usuario
Cisco
Cisco TelePresence SX10 Manual de usuario
Cisco
Cisco TelePresence MX700 Manual de servicio
Cisco
Cisco Tandberg 1700 MXP Instrucciones de montaje
Cisco
Cisco Webex Room Kit Plus Manual de usuario
Cisco
Cisco Quick Set C20 Manual de usuario
Cisco
Cisco Spark Room 70 Single Manual de usuario
Cisco
Cisco TelePresence SpeakerTrack 60 Manual de usuario
Cisco
Cisco TelePresence Profile Series Manual de usuario
Cisco
Cisco TelePresence SX10 Manual de usuario
Cisco
Cisco TelePresence Profile Series Manual de usuario
Cisco
Cisco TelePresence MX300 Manual de servicio
Cisco
Cisco TelePresence DX70 Manual de usuario
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
