Cisco SPA122 Manual de usuario
INSTALLATION GUIDE
1
Cisco SPA122 ATA Installation Guide
For analog phone or fax extensions
Activating Your Cisco ATA
You will need your activation code to activate your Cisco ATA. The activation code was sent via
email. You can also retrieve it in the 8x8 Account Manager by following these instructions:
1. Go to www.8x8.com, click Sign In and select Account Manager; enter your administrator
username and password.
2. Click Phone System from the top navigation bar, select View All Extensions, then click
Activate Device next to the extension you wish to activate.
3. A pop-up screen displays the activation code for the extension.
Note: If you are activating an Overhead Paging system, follow the special instructions provided
in the pop-up screen.
4. To activate your device for voice or fax service, connect an analog phone (or fax machine with
phone) to the Phone 1 port on the Cisco ATA. Lift the handset and follow the voice instructions
to enter the activation code. You will hear a message conrming your ATA is activated.
Installing your Cisco SPA122 ATA
Connect your device using the ports on the back panel. You will need either an analog phone or a
fax machine with an analog phone to activate your device using the Phone 1 port.
Fax Machine
(2nd-Port Fax Plan Only)
Computer or
Laptop
Internet Connection
(Router or Broadband Modem)
Power AdapterAnalog Phone, Fax
or Paging System
• Use the PHONE 1 port to connect an analog phone, analog overhead pager or fax machine with
an RJ-11 telephone cable. (If you purchased a 2nd-Port Fax Plan, connect that fax to the
PHONE 2 port.)
• The ETHERNET port connects to an individual network device, such as a PC or a laptop.
• The INTERNET port connects to your router or if you have no router, directly to your cable or
DSL broadband modem.
Note: If you connect directly to a broadband modem, you must rst congure your Cisco ATA to
act as a router. Please see the Using your Cisco ATA as a Router section.
• The Power port is where you connect your AC power adapter.
For further assistance
on activating your Cisco
SPA122 ATA, contact 8x8
Customer Support on
1.888.898.8733
INSTALLATION GUIDE
Cisco SPA122 ATA
2
Indicator Lights
The status of your adapter can be determined by looking at the indicator lights on the side panel.
Icons Light Description
PHONE 1 & 2
Steady green—On hook.
Slow ashing green—O hook.
O—Port not ready.
INTERNET
Flashing green—Transmitting or receiving data through the INTERNET (WAN) port.
O—No link.
SYSTEM
Steady green—System ready, IP address acquired.
Slow ashing green—Acquiring IP address. (By default, uses DHCP.)
Fast ashing green—Upgrading rmware.
O—No power or system can not boot up.
Making a Call for the First Time
To dial outside, dial the number:
• Long Distance (1-555-555-5555)
• Local Calls (555-5555 or 1-555-555-5555)
To dial internally, dial the extension number:
• 1001 (Extension)
• 555 (Voicemail)
• 444 (Auto Attendant)
INSTALLATION GUIDE
Cisco SPA122 ATA
3
Using your Cisco ATA as a Router
These instructions are only for use when you have no separate router, wireless router, or combination broadband
modem/router already in your network. This is for advanced users only.
If you do not have a router, you can connect your broadband modem directly into your Cisco ATA and then congure it to act as a router. Please
follow the instructions below to congure it:
Congure Cisco ATA as a Router
1. Determine the IP address of your Cisco ATA.
a. Plug in an analog phone to the Phone 1 or Phone 2 port.
b. Dial **** and you will hear the Cisco Conguration Menu.
c. Dial 110# to obtain the IP address of your Cisco ATA.
2. Access the Cisco ATA web interface to your Cisco ATA.
a. Open a browser window on your PC or laptop.
b. Enter the IP address into your browser. Your default Username is “cisco” and your default Password is “cisco”.
c. This should open up the conguration window. If you can’t access the conguration window:
• Recheck your IP address
• If you have diculty, plug your PC or laptop directly into the Ethernet port of the ATA and type in the IP address.
• If you still have diculty, go back to the IVR and dial **** from the phone connected to your ATA, then dial 7932# and then
dial 1to turn on the web interface.
INSTALLATION GUIDE
Cisco SPA122 ATA
NASDAQ: EGHT
www.8x8.com
© 2012. The 8x8, Inc. logo is a registered trademark of 8x8, Inc. 8x8, Inc. is a publicly traded company. PM482/312
The Champion
For Business
Communications
3. Under the Network Setup tab, under Basic Setup, select Network Service, then using the pull down menu select the item NAT to make
the SPA122 operate as a basic router, then click the Submit button. Refer to the diagram below.
After changing the SPA122 to router mode, your network administrator can use this same interface to make additional router settings
changes to congure the device to work with your Internet Service Provider (ISP) and broadband modem. Your ISP will provide those
settings and conguration requirements.
4. Your ATA Internet port can be connected directly to a broadband modem and the Cisco SPA122 can be used as an ATA for your phone, and
as a router for your PC or laptop when plugged directly into the Ethernet port of the ATA.
a. To return to the original settings, so your ATA device can be used with a router (rather than connected directly to a broadband modem),
select Bridge from the Networking Service pull-down menu.
If you need detailed instructions on connecting your Cisco ATA as a router to your Internet Service Provider, please refer to the Cisco SPA122
Administrator Guide at http://sims.8x8.com/GetDocument.aspx?docid=710739. Please contact 8x8 Support if you or your IT manager require
access to advanced settings not available under your login.
Otros manuales para SPA122
1
Tabla de contenidos
Otros manuales de Adaptador de Cisco
Cisco
Cisco Linksys PLEK400 Manual de usuario
Cisco
Cisco AIR-CB21AG-W-K9 Manual del operador
Cisco
Cisco LINKSYS WUSB54AG Manual de usuario
Cisco
Cisco ATA 186 Manual de usuario
Cisco
Cisco LINKSYS WUSB54GP Instrucciones de funcionamiento originales
Cisco
Cisco Linksys AE6000 Manual de usuario
Cisco
Cisco CVA122 Guía de configuración
Cisco
Cisco Linksys RT31P2 Manual de instrucciones
Cisco
Cisco LINKSYS WUSB54GC Manual de usuario
Cisco
Cisco MicroCell Manual de usuario
Cisco
Cisco Linksys PLS300 Manual de usuario
Cisco
Cisco Small Business SPA8800 Manual de usuario
Cisco
Cisco WUSB54GSC Manual de usuario
Cisco
Cisco PA-A2 Manual del operador
Cisco
Cisco PA-8T-232 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco PA-2JT2 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco WUSB54GC-RM - Refurb Wireless-g Compact USB Manual de usuario
Cisco
Cisco Small Business SPA2102 Manual de instrucciones
Cisco
Cisco WPC54G Manual de usuario
Cisco
Cisco LINKSYS USB1000 Manual de usuario
