Cisco ATA 191 Manual de instrucciones
Install the ATA 191
•ATA 191 Installation Information, page 1
•Network Requirements, page 1
•Safety Recommendations, page 2
•Package Contents, page 2
•Install Your Cisco ATA , page 2
•Attach a Phone to the ATA 191, page 3
•Startup Process Verification, page 3
•Configure Startup Network Settings, page 4
•Security on the ATA 191, page 4
ATA 191 Installation Information
You connect the ATA 191 hardware and configure the ATA 191 by loading the QED and firmware files.
Install the QED file first, then install the firmware file. For more information about loading the QED and
firmware files, see the "Installation Notes" section of the "Release Notes for Cisco ATA 191 Analog Telephone
Adapter".
Network Requirements
The ATA 191 acts as an endpoint on an IP telephony network. The following equipment is required:
•Call Control system
•Voice packet gateway—Required if you are connecting to the Public Switched Telephone Network
(PSTN). A gateway is not required if an analog key system is in effect.
•Ethernet connection
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager
1
Safety Recommendations
To ensure general safety, follow these guidelines:
•Do not get this product wet or pour liquids into this device.
•Do not open or disassemble this product.
•Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
•Use only the power supply that comes with the ATA.
•Ultimate disposal of this product should be handled according to all national laws and regulations.
•Read the installation instructions before you connect the system to its power source.
•The plug-socket combination must always be accessible because it serves as the main disconnecting
device.
•Do not work on the system or connect or disconnect cables during periods of lightning activity.
•To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
For translated warnings, see the Regulatory Compliance and Safety Information for the Cisco ATA 191
document.
Package Contents
The ATA 191 package contains the following items:
•Cisco ATA 191 Analog Telephone Adapter
•Regulatory Compliance and Safety Information for the ATA 191
•5V power adapter with appropriate country clip
•Ethernet cable
The ATA is intended for use only with the 5V DC power adapter that comes with the
unit.
Note
Install Your Cisco ATA
You can use either Category 3/5/5e/6 cabling for 10-Mbps connections, but you must use Category 5/5e/6 for
100-Mbps connections.
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager
2
Install the ATA 191
Safety Recommendations
Procedure
Step 1 Connect the power supply to the Cisco DC Adapter port.
Step 2 Connect a straight-through Ethernet cable from the network to the network port on the ATA. Each ATA ships
with one Ethernet cable in the box.
Attach a Phone to the ATA 191
Before You Begin
You can attach one or two phones to an ATA 191.
Procedure
Connect one or more phones to a phone port of the ATA with an RJ11 cable.
The PHONE1 and PHONE2 LEDs on the ATA light as solid green when there is activity on that port.
Startup Process Verification
After your ATA has power connected to it, it begins the startup process by cycling through these steps:
1The Power LED flashes during the startup process.
2The Problem Report Tool (PRT) LED lights solid amber during initial bootup. The LED then flashes
amber and then green while the application and kernel are booting.
If the PRT LED lights red during bootup, then either the MIC certificate failed, or the ATA failed to obtain
a network address.
3The LED for Phone 1 flashes while the Phone1 port boots, followed by the LED for Phone 2.
After the Phone1 and Phone2 ports register with Cisco Unified CM successfully, the corresponding LEDs
are lit with solid green. If a phone port fails to register, the LED rapidly flashes in green three times, then
repeats.
4When the ATA has successfully booted, the Power LED lights solid green and the PRT LED turns off.
The Network LED flashes as traffic is detected.
When you go offhook on the phone, the phone LED begins to flash, and you hear the dial tone. The ATA has
completed the startup process.
Related Topics
Start up Process with Standby Image
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager
3
Install the ATA 191
Attach a Phone to the ATA 191
Configure Startup Network Settings
Before You Begin
Perform this configuration if you are not using DHCP in your network.
Procedure
Step 1 Configure these network settings on the ATA after you install the device on the network:
•IP subnet information (subnet mask and gateway)
•TFTP server IP address
Step 2 Configure these optional settings as necessary:
•Administration VLAN ID
Step 3 Collect this information.
Security on the ATA 191
Security features protect against several threats, including threats to the identity of the phone and to data.
These features establish and maintain authenticated communication streams between the phone and the Cisco
Unified Communications Manager server, and digitally sign files before they are delivered.
For more information about the security features, see the Security Guide for Cisco Unified Communications
Manager.
You can start the installation of a Locally Significant Certificate (LSC) on the device profile from Cisco
Unified Communications Manager. Use the Device >Phone >Phone Configuration menu option. You can
also use this menu option to update or remove an LSC.
Before you begin, make sure that the appropriate Cisco Unified Communications Manager and the CAPF
security configurations are complete:
•On Cisco Unified Communications Operating System Administration, verify that the CAPF certificate
has been installed.
•The CAPF is running and configured.
See the Security Guide for Cisco Unified Communications Manager for more information.
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager
4
Install the ATA 191
Configure Startup Network Settings
Otros manuales para ATA 191
9
Tabla de contenidos
Otros manuales de Adaptador de Cisco
Cisco
Cisco LINKSYS USB1000 Manual de usuario
Cisco
Cisco SPA112 Manual de instrucciones
Cisco
Cisco PA-E3 Series Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco 10BASE-FL Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco Linksys AE1200 Instrucciones de instalación y funcionamiento
Cisco
Cisco PA-2JT2 Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco STM-1 Manual de usuario
Cisco
Cisco ATA 186 Guía de instalación
Cisco
Cisco iDTA153 Manual de usuario
Cisco
Cisco ATA 186 Manual de usuario
Cisco
Cisco LINKSYS WUSB54GC Manual de usuario
Cisco
Cisco ATA 186 Manual de usuario
Cisco
Cisco ATA 187 Manual de instrucciones
Cisco
Cisco MWA1221 Manual de usuario
Cisco
Cisco ATA 191 Manual de instrucciones
Cisco
Cisco AIR-PCM352 - Aironet 350 Series 11Mbps Wireless LAN PC Card... Manual del operador
Cisco
Cisco WUSB54GSC Manual de usuario
Cisco
Cisco Small Business SPA2102 Manual de instrucciones
Cisco
Cisco WUSB100 Manual de usuario
Cisco
Cisco PA-8T-232 Instrucciones de funcionamiento y mantenimiento
