Christie Q Series Manual de usuario

Q Series Lamp Hot Swap Instruction Sheet 1

020-101356-01 Rev. 1 (03-2014)

Q Series Lamp Hot Swap

Instruction Sheet

This document provides instructions for replacing a Q Series lamp using the hot swap method.

Safety Precautions

Tools and Hardware Required

• DWU951, DWX951, and DXG1051 replacement lamp (PN: 003-004774-XX)

• #2 Phillips screwdriver

Hot Swap Procedure Timing

The hot swap procedure must be completed in three minutes or the hot swap command is canceled

and the projector shuts down. The hot swap countdown is initiated when the first lamp cover screw is

loosened. The countdown completes when the lamp door is re-attached with its two screws

tightened.

Failure to comply with these safety precautions results in death or serious injury.

• Lamp replacement must be performed by a Christie authorized service technician.

• Never attempt to remove the lamp when hot. The lamp is under a great deal of pressure

when hot and may explode, causing personal injury or death and/or property damage.

Allow the lamp to cool completely before handling.

• Always wear manufacturer approved protective safety clothing (gloves, jacket, face

shield) whenever the lamp door is open or when handling the lamp. Only qualified

technicians should install projector lamps.

• If the lamp is blown out, do not perform this procedure.

Failure to comply with these safety precautions could result in death or serious injury.

• Possibly hazardous optical radiation emitted from this product. (Risk group 3)

• Thermal radiation emitted from this product may cause burns. (Risk group 3)

• Do not insert your hand or tools into the lamp house while the lamp is removed.

Do not look straight into the ignited lamp or strongly lighted portion after the lamp is

removed. Failure to comply with this safety precaution might cause decreased vision or loss

of sight.

Q Series Lamp Hot Swap Instruction Sheet

Q Series Lamp Hot Swap Instruction Sheet 2

020-101356-01 Rev. 1 (03-2014)

Replace a Lamp Using the Hot Swap Method

1. While the lamp is on, press Function and then Zoom and hold for a minimum of three seconds.

2. From the Setup menu, press Select Lamp and press the Up or Down arrows to determine

which lamp to change.

3. To select the lamp, press the Right arrow.

The selected lamp turns off and the LED located on the back of the projector displays red.

If a lamp error has previously occurred, the lamp name needing to be replaced is displayed in the

LCD monitor. Hot swap mode is automatically selected for the lamp needing to be replaced. Both

the front and back LAMP-# LEDs display red.

4. Wait 45 minutes for the lamp to cool down.

5. When the back LAMP-#LED is solid orange, remove the two screws on the lamp cover.

Where #is the number of the lamp you are changing.

If you open the lamp door while the LED is flashing, it turns off both lamps and you receive a

COVER[open] error.

6. Remove the lamp cover.

7. Remove the three lamp screws.

8. Remove the lamp by its handle.

9. Insert the new lamp.

10. Tighten the three lamp screws.

11. Re-attach the lamp cover and tighten the two screws.

The back LAMP-#LED blinks orange. The front LAMP-#LED turns off if lit due to a previous lamp

error.

12. To reset the run time, from the Setup menu select Lamp & Filter > LAMP-#Time.

When successfully reset, the back LAMP-# LED turns off. If the LED continues to blink orange,

the lamp run time is not initializing. Refer to the Operator’s Guide for details on how to reset the

lamp run time.

13. To return to normal display in the LCD monitor, press Function.

Technical Support

North and South America: +1-800-221-8025 or [email protected]

Europe, Middle East, and Africa: +44 (0) 1189 778111 or [email protected]

Asia Pacific: tech-[email protected]

Otros manuales para Q Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de Christie

Christie

Christie LW400 Manual de usuario

Christie

Christie M Series Manual de usuario

Christie

Christie E Series Manual de usuario

Christie

Christie DS+305 Manual de usuario

Christie

Christie DWU1052 Manual de usuario

Christie

Christie DS Series Manual de usuario

Christie

Christie LWU701i Manual de usuario

Christie

Christie 38-RS1002-01 Manual de usuario

Christie

Christie LX400 Manual de usuario

Christie

Christie DWU500S Manual de usuario

Christie

Christie Mirage S+ 4K Manual de usuario

Christie

Christie Crimson Series Manual de uso y cuidado

Christie

Christie 38-VIV306-01 Manual de usuario

Christie

Christie CP2208-LP Manual de usuario

Christie

Christie DS+60 Manual de usuario

Christie

Christie DS Series Manual de usuario

Christie

Christie Mirage M Series Manual de usuario

Christie

Christie DS+650 Manual de usuario

Christie

Christie LHD700 Manual de usuario

Christie

Christie Boxer 4K Series Manual de usuario

Christie

Christie CP4230 Manual de usuario

Christie

Christie HD5Kc Manual de usuario

Christie

Christie 38-VIV211-01 Manual de usuario

Christie

Christie CP2220 Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario