Christie DS Series Manual de usuario
DS Series
LWU1200-DS
User’s Manual (detailed)
Firmware upgrade of the projector
020-001901-01
1
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
Firmware update of the projector
Firmware update of the projector
The update le may be published on our website to add functions or x defects.
The following is how to update the projector rmware by yourself.
Our website: http://www.christiedigital.com
►Follow the procedure for updating the rmware. Follow the instructions. When
the instructions are not followed, the projector may not start up correctly. Update
the rmware at your own responsibility.
• Never turn off the projector during the update. When the projector is
unexpectedly turned off, disconnect the power cord and allow the projector to
cool down sufciently. After the projector has sufciently cooled down, turn on
the projector again and start the rmware update again from the beginning.
• Never remove the USB storage device while using it for the update.
• When updating the rmware by using the Web Control screen, make sure that
the network is not disconnected during the update. Wireless LAN is more likely
to be disconnected than wired LAN. Wired connection is recommended.
• Updating cannot be cancelled after starting it.
• Firmware cannot be back to the old version.
• The network function of the projector cannot be used during the update.
• HTTP is used for uploading the update le. Conrm with a network
administrator that there is no restriction of the le uploading.
CAUTION
The network function does not work properly after the update
1. Connect the power cord and turn on the projector, after pulling out the power
cord and leaving the projector for more than one minute.
2. Conrm the network setting of the projector after waiting more than two minutes.
Some of the settings may return to the default after the rmware update.
3. When the projector does not work properly and there is no problem in the
network settings, please contact your dealer.
2
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
Firmware update of the projector
1 Preparation
It is necessary to get an update le from our website.
The applicable update le can be selected from "Firmware Version" and "Model
Name" of the projector on our website.
Conrm "Model Name" and "Firmware Version", and download the update le.
1.1 Conrming the "Model Name" and "Firmware Version"
1. There are two conrmation methods.
• Select OPTION - SERVICE - FIRMWARE UPDATE in ADVANCED MENU of
the projector.
(The following is an example.)
Model Name LWU1200-DS
Firmware Version PRJ_LWU1200-DS_V0100
• Select Firmware Update from Main Menu in the Projector Web Control.
(The following is an example.)
Model Name LWU1200-DS
Firmware Version PRJ_LWU1200-DS_V0100
2. Take a note of the content of “Model Name” and “Firmware Version”.
1.2 Downloading the update le
Use a computer that can be connected to the Internet, and download the update
le from our website. For more information, please check our website.
NOTE • Do not change the name of an update le. The update may not be
performed correctly.
When the same update les are downloaded, subscripts may be added.
Make sure to use the le without subscripts.
(good example) PRJ_LWU1200-DS_V0100
(bad example) PRJ_LWU1200-DS_V0100(1)
3
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
Firmware update of the projector
2 Update
There are two ways of update: "update using a USB storage device" and "update
using the Web Control via network connection".
Each method is as follows.
2.1 Update by using the USB storage device
○ Necessary equipment
USB storage device
• USB2.0 compliant
• Memory capacity 32GB or less (100MB or more space is required)
• FAT16 and FAT32 format are supported.
○Update procedure
1. Make a folder in a USB storage device to save an update le.
Create a "PRJ" folder using single-byte uppercase letters in the root directory of
a USB storage device.
[USB storage device] ----
►Make sure to save the update le as follows. If the update le is not saved
correctly, the projector cannot recognize it.
• Create "PRJ" folder in the root directory of a USB storage device.
• Name a folder using single-byte uppercase letters.
• Save only one update le of the model you want to update in “PRJ” folder.
If plural les are saved in this folder, the projector may not recognize the
update le correctly.
CAUTION
PRJ
2. Save the downloaded le in “PRJ” folder made in step 1.
3. Turn on the projector and the light source.
4. Insert the USB storage device to the projector after waiting at least two minutes.
Do not connect two or more USB storage devices.
5. Select OPTION - SERVICE - FIRMWARE UPDATE in ADVANCED MENU
of the projector.
File saved in the "PRJ" folder in the USB storage device is displayed. Make
sure that the le name is correct.
When the le name is not displayed, conrm step 1.
4
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
Firmware update of the projector
6. When you perform the update, select “YES”.
7. The update is completed in about a few minutes, and the projector restarts
automatically.
The following message is displayed after rmware update has completed
normally.
The projector will automatically turn off the light source to reect the updated
rmware in the operation. After the light source is turned off for a short time, the
light source is automatically turned on again.
After the light source is turned on, conrm the rmware version in OPTION -
SERVICE - FIRMWARE UPDATE in ADVANCED menu.
5
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
2.2 Update by Web Control via the network connection
○Necessary equipment
Computer that can be connected to a wired or wireless network by Web Control
• Use a browser which operation has been con rmed.
For more information, please check our website.
• Prepare a LAN cable or a router necessary for connection.
○Update procedure
1. Copy the downloaded update le to the computer that can connect to the Web
Control.
2. Turn on the projector.
3. Select Firmware Update from Main Menu after connecting to Web Control.
Select the update le saved in Computer by using the [Browse...] button.
When an appropriate le is selected, the [Update Firmware] button gets ready
to be clicked.
4. Click the [Update Firmware] button to update.
Firmware update of the projector
5. The update is completed in about a few or several minutes (it depends on le
transfer speed), and the projector restarts automatically.
Con rm the rmware version in the Projector Web Control - Main Menu -
Firmware Update after the restart has been completed.
6
LWU1200-DS
User's Manual - Firmware upgrade of the projector 020-001901-01 Rev. 1 (01-2021)
LIT MAN USR LWU1200-DS Upgrade
Firmware update of the projector
NOTE • Do not operate the browser during the rmware update.
• The update may not be performed correctly if the device you are using goes
to sleep mode during the rmware update.
• The projector cannot be controlled or its settings cannot be changed from the
web screen during the rmware update.
• The rmware can also be updated by using a USB storage device. The update
by Web Control cannot be performed during the update by using a USB storage
device.
• The rmware update cannot be executed when STANDBY MODE in the
SETUP menu is set to NETWORK-WOL and the projector is in standby mode
(light source is not turned on).
Set STANDBY MODE to NORMAL or QUICK START, or turn on the power and
make sure the light source is on to execute the update.
•
The rmware update cannot be executed when the shutter function of the
projector is on. Please execute the rmware update with the shutter function off.
Corporateoffices Worldwide offices
Christie Digital SystemsUSA,Inc.
ph: 714 236 8610
ChristieDigitalSystemsCanadaInc.
ph: 519 744 8005
Africa
ph:+27(0)11 510 0094
Australia
ph:+61(0)73624 4888
Brazil
ph:+55(11)2548 4753
China (Beijing)
ph:+86 10 6561 0240
China (Shanghai)
ph:+86 21 6030 0500
Columbia
ph:+57(318)447 3179
Gemany
ph:+49(0) 221 99512 0
India
ph:+91(080)67089999
Japan(Tokyo)
ph:81 33599 7481
Korea(Seoul)
ph:+82 2702 1601
Mexico
Ph:+52 55 4744 1790
Singapore
Ph:+65 6877 8737
Spain
Ph:+34 91 633 9990
Middle East
Ph:+971(0)503 6800
United Kingdom
Ph:+44(0)118 9778000
United States (Arizona)
ph: 602 943 5700
Independant sales
consultant offices
Italy
ph: +39 (0) 2 9902 1161
Russia
ph: +36 (0) 1 47 48 100
For the most current technical documentation, visit www.christiedigital.com.
Otros manuales para DS Series
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Proyector de Christie
Christie
Christie LX501 Manual de usuario
Christie
Christie LW40U Manual de usuario
Christie
Christie CP4415-RGB Gen2 Instrucciones de montaje
Christie
Christie Mirage 304K Manual de usuario
Christie
Christie LW720 Manual de usuario
Christie
Christie Lcd projector Manual de usuario
Christie
Christie LX505 Manual de usuario
Christie
Christie DHD675-E Manual de usuario
Christie
Christie Crimson Manual de uso y cuidado
Christie
Christie CineLife+ 4K-RGB Instrucciones de montaje
Christie
Christie CineLife+ CP4415-RGB Instrucciones de montaje
Christie
Christie DS Series Manual de usuario
Christie
Christie DS+26 Manual de usuario
Christie
Christie I Series Manual de usuario
Christie
Christie Boxer 30 Instrucciones de montaje
Christie
Christie D4K2560 Manual de usuario
Christie
Christie Vivid Lite Manual de usuario
Christie
Christie Mirage S+2K Manual de usuario
Christie
Christie CCM-LX Manual de usuario
Christie
Christie GS Series Manual de usuario
