Chiayo Live-100 series Manual de usuario

UHF 2-Way Synchronising True Diversity / Diversity Wireless Microphone System

ISO 9001

ISO 14001

OHSAS 18001

GREEN PRODUCT

Operation Manual

IS O

1 4 0 0 1

R E G I S T E R E D

O H S A S

1 8 0 0 1

R E G I S T E R E D

-1-

Thank you for choosing this wireless microphone system!

Our products are designed to last and for user-friendly operation. Each system consists of:

1. A receiver

2. A handheld or beltpack transmitter

3. A pair of antennas

4. A switching adaptor

5. An operation manual

For more details, please take a few moments to read this operating manual to gain a

thorough understanding of the function and operation of both transmitter and receiver.

Parts and functions of SDR-6200 IrDA/SDR-6100 IrDA receiver

Front panel

1. Power switch

2. IR sensor area

3. Diversity indicator

4. Audio signal indicator

5. LCD display

6. UP button

7. DOWN button

8. IrDA synchronisation button

9. SET button

Rear panel

SDR-6200 IrDA

SDR-6100 IrDA

POWER

D I V E R S I T Y

A B

A U D IO SDR-61 00 IrDA UHF 2-WAY SYNC. DIVERSITY RECEIVER

3 4

10 11 12 13

L IN E O U T

UN BA LA NC EDB A L A N C E D

D C I N

12V

A N T.AA N T.B

1 .G N D

M IC O U T

12 13 14

-2-

10. Antenna B socket (TNC)

11. Balanced audio output

12. Unbalanced audio output

13. Antenna A socket (TNC)

14. DC in

Changing CHANNEL / FREQUENCY

First, press "SET" till the display shows .

Then press UP or DOWN to select a new channel. As the channel changes, the

frequency changes accordingly, too. After the setting is made, the data will be

automatically saved.

CHANNEL scanning

For an interference-free operation, a cleaner channel might be necessary if the current

one receives too much interference. Before scanning, the transmitter must be switched off.

First, press "SET" till the display shows .

Then press UP or DOWN to go to the next clean channel.

After the setting is made, the data will be automatically saved.

CHANNEL SYNCHRONISING of the receiver and microphone

a. Limit the distance between the receiver and transmitter within 30cm.

b. Align both infrared areas

c. To change the receiver’s channel, please press the synchronising button of the microphone.

The microphone's LED will grow to imply synchronising signal transmitted and

will appear on the receiver's LCD, which means the receiver has been

successfully synchronised.

d. To change the microphones channel, please press the SYNC button of the receiver and

will appear on the receiver’s display, followed by

indicating data transferred.

-3-

Adjusting VOLUME level

The setting can be made right on the main menu .

Press UP or DOWN to choose a new level. After the setting is made, the data will be

automatically saved.

Adjusting SQUELCH level

First, press "SET" till the display shows .

Then press UP or DOWN to choose a new level. After the setting is made, the data will be

automatically saved.

Receiver installation

For best operation, the receiver should be at least 1m above the

ground and 1m away from a wall or metal surface to minimise

reflections. The transmitter should also be at least 1m away from

a wall or metal surface to minimise reflections. The transmitter

should also be at least 1m away from the receiver. Keep

antennas away from noise source such as motors, automobiles,

neon light as well as large metal objects.

Audio output connection

There are two audio outputs on the back of the receiver, Mic-level balanced and Line-

level unbalanced. Use shielded audio cable for the connection between the receiver and

the amplifier/mixer. If the amplifier/mixer has a 1/4"(6.3mm) phone jack, connect a cable

from the 1/4"(6.3mm) unbalanced audio output from the receiver to the amplifier/mixer. If

the amplifier/mixer has an XLR input, connect a cable from the balanced XLR audio

output from the receiver to the amplifier/mixer input.

Rack mounting

The receiver can be cabinet-mounted by either one or two units. If only one receiver is to

be mounted, an optional kit is available and it's installed as shown in Fig 1. If two

receivers are to be mounted, they can be assembled by another kit and installed as

shown in Fig 2.

(Fig 1)

(Fig 2)

-4-

UHF handheld microphones（SQ-6100 IrDA/SQ-2100 IrDA/SQ-1100 IrDA）

SQ-6100 IrDA

SQ-2100 IrDA

SQ-1100 IrDA

Parts and functions

SQ-6100 IrDA

SQ-2100 IrDA

SQ-1100 IrDA

Cartridge

Battery power LED

Power switch

LCD

Menu button

Setting button

IrDA synchronising button

Battery compartment

Color cap

IrDA sensor area

Charging port

Battery installation & indicator

This microphone requires 2 x AA batteries to operate.

To install, remove the battery cover and slide the batteries into the battery compartment &

replace the battery cover.

Note: Batteries contain a corrosive acid that may leak and damage the microphone when

stored for a long period. Batteries should be removed from the microphone before storing

without use for more than 4 weeks.

When the microphone is switched ON a red LED (2) will blink once to indicate the batteries

installed are in good condition. If the LED remains illuminated the batteries have expired

and require replacement.

1 2 3 7

4 5

-5-

Channel synchronising of the receiver and microphone

1. Limit the distance between the receiver and transmitter within 30cm.

2. Align both sensor areas

3. To change the receiver’s channel, please press the synchronising button of the microphone.

The microphone's LED will grow to imply synchronising signal transmitted to the receiver

and change its channel.

4. To change the microphone’s channel, please press the synchronising button of the receiver.

The receiver will transmit synchronising signal to the microphone and change its channel.

Other settings（SQ-6100 IrDA）

1. Channel setting

Use SET button to go to the CHANNEL/ FREQUENCY page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Pressing SET/MENU buttons will increase/decrease the channel number. The corresponding

frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically

saved.

2. Battery type setting

Use SET button to go to the BATTERY TYPE page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3

seconds after selecting a channel, it will be automatically saved.

Remark: NiMH battery must be selected when rechargeable battery is being used. Never select

AKLN (alkaline) when microphone is intended for charging, as alkaline battery isn’t

rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong

and misleading status information.

-6-

UHF belt-pack transmitters（SM-7100 IrDA/SM-6100 IrDA/SM-1100 IrDA）

SM-7100 IrDA/SM-6100 IrDA SM-1100 IrDA

Parts and functions

SM-7100 IrDA

SM-6100 IrDA

SM-1100 IrDA

Antenna

LCD

Cover release button

Power switch

IrDA synchronising button

Menu button

Setting button

High-impedance gain control (GT)

Low-impedance gain control (MT)

Battery compartment

Audio mute switch

Battery power LED

IrDA sensor area

Mini XLR connector

Charging contacts

3 3

84 5

11 12

11 11

-7-

Battery installation & indicator

This belt-pack requires 2 x AA batteries to operate.

To install, open the battery cover using the cover release buttons and insert the batteries into

the battery compartment.

Note: Batteries contain a corrosive acid that may leak and damage the belt-pack when stored

for a long period. Batteries should be removed from the belt-pack before storing without use for

more than 4 weeks.

When the microphone is switched ON, the battery power LED (red) will blink once to indicate

the batteries installed are in good condition. If the LED remains illuminated the batteries

have expired and require replacement.

Channel synchronising of the receiver and transmitter

1. Limit the distance between the receiver and transmitter within 30cm.

2. Align both sensor areas

3. To change the receiver’s channel, please press the synchronising button of the transmitter.

The transmitter's LED will grow to imply synchronising signal transmitted to the receiver and

change its channel.

4. To change the transmitter’s channel, please press the synchronising button of the receiver.

The receiver will transmit synchronising signal to the transmitter and change its channel.

GAIN setting (GT/MT)

Gain control enables the user to set different output levels. GT is for the use of instrument with

high impedance, such as guitar while MT is for the use of low impedance such as lapel or

headset microphones.

Other settings（SM-7100 IrDA/SM-6100 IrDA）

1. Channel setting

Use SET button to go to the CHANNEL/ FREQUENCY page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Pressing SET/MENU buttons will increase/decrease the channel number. The corresponding

frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically

saved.

-8-

2. Battery type setting

Use SET button to go to the BATTERY TYPE page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3

seconds after selecting a channel, it will be automatically saved.

Remark: NiMH battery must be selected when rechargeable battery is being used. Never select

AKLN (alkaline) when transmitter is intended for charging, as alkaline battery isn’t

rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong

and misleading status information.

-9-

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de micrófono de Chiayo

Chiayo

Chiayo AIR-812 Manual de usuario

Chiayo

Chiayo NDR-3100 Manual de usuario

Chiayo

Chiayo SDR-6200 IrDA Manual de usuario

Chiayo

Chiayo IRX2 Manual de usuario

Chiayo

Chiayo QR-2000N Manual de usuario

Chiayo

Chiayo IRX2 Manual de usuario

Chiayo

Chiayo SQ-6100 IrDAR Manual de usuario

Chiayo

Chiayo SDR-8200 Manual de usuario

Chiayo

Chiayo RR-2000 Manual de usuario

Chiayo

Chiayo Q-200 Manual de usuario

Chiayo

Chiayo QR-4000N Manual de usuario

Chiayo

Chiayo IWM-202 Manual de usuario

Chiayo

Chiayo QR-4000 U Manual de usuario

Chiayo

Chiayo RRS-2000 Manual de usuario

Chiayo

Chiayo R-1001 Manual de usuario

Chiayo

Chiayo SDR-5100 IrDA Manual de usuario

Chiayo

Chiayo R-1010 Manual de usuario

Chiayo

Chiayo IWR-320 Manual de usuario

Chiayo

Chiayo Artist Manual de usuario

Chiayo

Chiayo Smart 300 Manual de usuario

Chiayo

Chiayo R-1001 Manual de usuario

Chiayo

Chiayo Stage-100 Series Manual de usuario

Chiayo

Chiayo UDR-500 Manual de usuario

Chiayo

Chiayo DWR-5420 Manual de usuario

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario