Check-line CDT-1000HD Manual de usuario
1
OI407G-1000
TABLE OF CONTENTS
01.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
02.0 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
03.0 CONTENTS OF COMPLETE OUTFIT . . . . . . . . . . . . . . . . . .3
04.0 OVERVIEW OF CDT-1000HD . . . . . . . . . . . . . . . . . . . . . . . . .4
4.1 LCD Display
4.2 Front Panel Key Functions
05.0 INSTALLING BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
06.0 REMOVING PROTECTIVE RUBBER SHELL . . . . . . . . . . . .5
07.0 MEASURING RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
08.0 MEMORY SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
99.0 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
10.0 SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
11.0 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
8
9.0 SPECIFICATIONS
10.0 SPARE PARTS
Measuring Ranges
RPM 1.00 – 99,999 rpm (non-contact)
Resolution .01 from 0 –100
.1 from 100 – 1,000
1 from 1000 – 99,999
Accuracy ± 0.02% of reading or ±1 digit
Display 5-Digit LCD, 10mm high
Decimal Point Automatic
Memory System Maximum, minimum, last reading and average (retained
in memory for the life of batteries)
Measurement System
Non-Contact Visible LED light beam
Engineering units
RPM RPM
Sensing Distance Up to 24 inches (60 cm)
Display Update Time 0.5 seconds
Auto Power Off After 30 seconds of non-use (minimum, maximum,
last and average reading retained in memory)
Battery Life 30 hours continuous use, approx.
Battery Type 2 AA (1.5V) or rechargeable
Weight 5 ounces (140 grams)
Housing Material ABS Plastic
Operating Temperature 32 to 122° F (0 to 50° C)
Storage Temperature – 4 to 150° F (–20 to 70° C)
Accessories Included Reflective tape, 2 AA batteries and operating instructions
in a foam-fitted, hard-plastic carrying case,
NIST-traceable calibration certificate
Warranty 5 years
P/N: CDT-TAPE 10 strips of reflective tape—1/2" x 4" (12 x 100mm)
2
1.0 INTRODUCTION
The CDT-1000HD Digital Tachometer accurately measures RPM without
contacting the rotating element or object. A small piece of reflective tape
(supplied) is applied to the rotating element (shaft, wheel, etc.) The CDT-
1000HD utilizes a visible LED light beam to accurately measure the RPM
from a distance of up to 24 inches (60 cm) away from the “target.”
The CDT-1000HD is supplied with a built-in memory system which permits
the user to recall the maximum, minimum and last reading to the display for
viewing. It is powered by two (2) AA batteries (supplied).
1.1 Applications
Non-Contact RPM — Used when contact
measurement is not possible due to access
space restrictions, safety concerns, etc.
2.0 SAFETY PRECAUTIONS
All operators should wear safety goggles when using this or any other
tachometer. Failure to do so could result in serious injury!
7
8.0 MEMORY SYSTEM
The CDT-1000HD is supplied with
a built-in memory system which
stores the last measurement, maximum
measurement, minimum measurement,
and the average measurement which
occurred during a measuring period.
A measuring period is the interval of time while the Measure key is
depressed. The stored values are retained in memory even when the power
turns off (auto power off). To recall the stored values after auto power off:
1. Press the Measure key to turn the power on
2. Press the MEM key to recall the desired value
The Memory key accesses the CDT-1000HD’s built-in
memory. Each time the MEM key is pressed the values
stored in memory will be recalled to the display in the sequence listed
below. The appropriate memory indicator will be shown together with
the recalled value on the display.
Note: When the batteries are removed, the values stored in memory
will be lost.
MEM
MEM
MAX
MIN
AV
rpm
8.8.8.8.8
MEM
MAX
MIN
AV
rpm
8.8.8.8.8
MEM
MAX
MIN
AV
rpm
8.8.8.8.8
MEM
MAX
MIN
AV
rpm
8.8.8.8.8
Last
Maximum
Minimum
Average
3
3.0 CONTENTS OF COMPLETE OUTFIT
1
3
2
The CDT-1000HD is supplied with the following accessories in a foam-fitted,
carrying case:
1. Meter with molded rubber shell
2. Reflective Tape (10 strips)
3. Two AA Batteries
4. NIST-traceable Calibrations Certificate (not shown)
5. Instruction Manual (not shown)
6
7.0 MEASURING RPM
1. Attach a piece of reflective tape to the rotating
element (shaft, pulley, etc.).
2. Aim the CDT-1000HD at the target
using the red visible light beam for
alignment assistance.
3. Press and hold the Measure key to begin taking
measurements. The “On-Target” indicator on the
LCD will flash on and off if the instrument is
properly aimed at the target (reflective tape).
4. Release the Measure key prior to removing the
instrument from the target. The last reading
will be retained on the LCD display.
Hints for Non-Contact Measurements
1. The non-reflective area should be larger than the reflective area.
2. If the rotating element is highly reflective, cover it with black
tape or paint to improve the contrast between the reflective tape
and the surface of the rotating element.
Reflective Tape
4
4.0 OVERVIEW OF CDT-1000HD
4.1 LCD Display
1. On-Target Indicator — Indicates that the unit is lined up
correctly for an accurate measurement
2. Memory Indicators — Indicates which measurement
stored in memory (last, max., min., avg) is displayed.
3. Low Battery Indicator — Illuminates to indicate that
batteries need replacement.
4.2 Front Panel Key Functions
4. MEM: Acesses the memory. Each time the key is pressed
the values stored in memory will be recalled to the display.
5. MODE: Not functional in this model.
6. MEASURE: Performs the following functions:
• Turns on the power
• Starts and stops the measuring period
• Exits from the memory mode
1
2
5
6
4
3
5
5.0 INSTALLING BATTERIES
1. Turn the gauge over and locate the battery
compartment. You do not have to remove
the rubber shell.
2. Open the battery compartment by pulling
down on the tab located at the top of the
battery cover and remove the cover.
Insert two AA batteries following the
orientation engraved on the inside of the
battery compartment.
3. Replace the battery cover by inserting the
two tabs located on the bottom edge of the
cover into the matching slots in the housing.
4. Push the cover closed until the tab at the top
of the battery cover “clicks” into position.
5. Replace the cut-out section of the protective
rubber shell.
6.0 Removing Protective Rubber Shell
The gauge is supplied with a durable rubber
shell that provides an added measure of
physical and environmental protection in
harsh applications.
To remove the shell, follow the procedure
outlined below:
1. Using your thumbs, slide the rubber shell
up and off of one corner of the gauge.
Repeat for the other corner
2. Pull the shell down until it is completely
off the corners of the gauge, the pull the
gauge forward and out of the shell.
3. Replace the shell by sliding the gauge
bottom first into the large center opening,
then, one at a time, slip the corners of the
shell back over the gauge.
click
12.0 WARRANTY
ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the
original purchaser that this product is of merchantable quality and confirms in
kind and quality with the descriptions and specifications thereof. Product failure or
malfunction arising out of any defect in workmanship or material in the product
existing at the time of delivery thereof which manifests itself within one year from
the sale of such product, shall be remedied by repair or replacement of such product,
at ELECTROMATIC’s option, except where unauthorized repair, disassembly, tamper-
ing, abuse or misapplication has taken place, as determined by ELECTROMATIC. All
returns for warranty or non-warranty repairs and/or replacement must be authorized by
ELECTROMATIC, in advance, with all repacking and shipping expenses to the
address below to be borne by the purchaser.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE
WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR
PURPOSE OR APPLICATION. ELECTROMATIC SHALL NOT BE RESPONSIBLE
NOR LIABLE FOR ANY CONSEQUENTIAL DAMAGE, OF ANY KIND OR
NATURE, RESULTING FROM THE USE OF SUPPLIED EQUIPMENT, WHETHER
SUCH DAMAGE OCCURS OR IS DISCOVERED BEFORE, UPON OR AFTER
REPLACEMENT OR REPAIR, AND WHETHER OR NOT SUCH DAMAGE IS
CAUSED BY MANUFACTURER’S OR SUPPLIER’S NEGLIGENCE WITHIN
ONE YEAR FROM INVOICE DATE.
Some State jurisdictions or States do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation may not apply to you. The duration
of any implied warranty, including, without limitation, fitness for any particular
purpose and merchantability with respect to this product, is limited to the duration of
the foregoing warranty. Some states do not allow limitations on how long an implied
warranty lasts but, not withstanding, this warranty, in the absence of such limitations,
shall extend for one year from the date of invoice.
ELECTROMATIC Equipment Co., Inc.
600 Oakland Ave. Cedarhurst, NY 11516—USA
Tel: 1-800-645-4330/ Tel: 516-295-4300/ Fax: 516-295-4399
Every precaution has been taken in the preparation of this manual. Electromatic Equipment Co., Inc., assumes
no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of
information contained herein. Any brand or product names mentioned herein are used for identification purpos-
es only, and are trademarks or registered trademarks of their respective holders.
CDT-1000HD
Non-Contact Tachometer
Operating Instructions
CHECK
•
LINE®
BY ELECTROMATIC
Distributed by: ABQ Industrial LP USA
Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451
Web: https://www.abqindustrial.net E-mail: [email protected]
Tabla de contenidos
Otros manuales de Instrumento de medición de Check-line
Check-line
Check-line TI-25MX Manual de usuario
Check-line
Check-line TI-CMXDL Manual de usuario
Check-line
Check-line MINI-MAX Manual de usuario
Check-line
Check-line MKM Manual de usuario
Check-line
Check-line DX2/DXX Manual de usuario
Check-line
Check-line CDT-2000HD Manual de usuario
Check-line
Check-line BLL Manual de usuario
Check-line
Check-line TI-25SX Manual de usuario
Check-line
Check-line ULTRASONIC TI-25LT Manual de usuario
Check-line
Check-line CTM Manual de usuario
Check-line
Check-line TI-CMX Manual de usuario
Check-line
Check-line DLM 107A Manual de usuario
Check-line
Check-line ETB Manual de usuario
Check-line
Check-line TI-25M Manual de usuario
Check-line
Check-line DCF-900 Manual de usuario
Check-line
Check-line DLM-107A Manual de usuario
Check-line
Check-line BTM-400PLUS Manual de usuario
Check-line
Check-line DTS-200 Manual de usuario
Check-line
Check-line StroboVision SMS-400B Manual de usuario
Check-line
Check-line RH6 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario