Chamberlain 050DCTWFLK Manual de usuario

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 050DCTWFLK

1.2 To maintain your warranty,

place the provided label

over the existing label

on the end panel of the

garage door opener.

1.1 Remove the light lens by pulling

the top sides of the light lens

and rotate the light lens down.

Squeeze the light lens clips to

remove lens from end panel.

1.3 Disconnect electrical and battery

power (if applicable) to the

garage door opener.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals

(A). Disconnect any wires from the lock terminals.

Remove the receiver logic board end panel from the

garage door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers, to

remove the harnesses.

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

Screws

Wire clip

Clips

To insert or remove the wires from the terminal,

push in the tab with a screwdriver tip.

Lock

Terminals

Red

White

Grey

Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the MyQ®serial number found on the provided label to add your

garage door opener to your MyQ®account. The products illustrated in the instructions are for reference. Your product may look different.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

Front of Logic Board

End Panel

Button Pad

Back of Logic Board

Install new receiver logic board

3.1 Connect the wire harnesses to the

new receiver logic board. When

reconnecting the wire harness, be sure

the tabs on the wire harness are facing

the end panel, not the logic board.

3.3 Reinsert the wires.

Door control wires:

• white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires:

• white wires into the white terminal.

• white/black wires into the

grey terminal.

Reconnect any lock terminal wires.

NOTE: A test of the safety reverse system is necessary for safe operation.

To insert or remove the wires from

the terminal, push in the tab with a

screwdriver tip.

Programming

1.1 Press and release the Learn button on the garage door opener. The Learn indicator light will

glow steadily for 30 seconds.

1.2 Within 30 seconds, press and hold the

button on the remote control.

1.3 Release the button when the garage door

opener light blinks. It has learned the

code. If light bulbs are not installed, two

clicks will be heard.

Program a remote using the learn button

Learn

Indicator

Light

Yellow Learn

Button

3.4 Install the light lens by aligning with

the hinges and snapping into place.

Reconnect power.

NOTE: When installing the light lens, ensure the

antenna wires are hanging straight down.

Red

White

Grey

Logic Board

Wire Clip

End Panel

Wire

Harness

Tabs

3.2 Insert the antenna wires through

the holes in the end panel. Snap the

receiver logic board into place on the

end panel and fasten with screws.

NOTE: Some

models will require

the short antenna

wire to be placed in

the traps of the end

panel.

Antenna wires

Antenna

wires

To program the Wi-Fi garage door opener to your network refer to your owner’s manual.

For garage door openers without a battery

back up system: remove the button pad from

the logic board and replace it with the alternate

button pad.

NOTE: If your logic board

has a wire clip, use the

wire clip to hold wires to

the logic board.

Lock

Terminals

Program the travel

Without a properly installed safety reversal

system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by

a closing garage door.

• Incorrect adjustment of garage door travel

limits will interfere with proper operation

of safety reversal system.

• After ANY adjustments are made, the

safety reversal system MUST be tested.

Door MUST reverse on contact with 1-1/2"

(3.8 cm) high object (or 2x4 laid ﬂat) on

ﬂoor.

1.1 Press and hold the Adjustment Button

until the UP Button begins to ﬂash and/

or a beep is heard.

1.2 Press and hold the UP Button until the

door is in the desired UP position.

1.3 Once the door is in the desired

UP position press and release the

Adjustment Button. The garage door

opener lights will ﬂash twice and the

DOWN Button will begin to ﬂash.

NOTE: The UP and DOWN Buttons can be used to move

the door up and down as needed.

1.4 Press and hold the DOWN Button

until the door is in the desired DOWN

position.

NOTE: The UP and DOWN Buttons can be used to move

the door up and down as needed.

1.5 Once the door is in the desired

DOWN position press and release the

Adjustment Button. The garage door

opener lights will ﬂash twice and the UP

Button will begin to ﬂash.

1.6 Press and release the UP Button.

When the door travels to the

programmed UP position, the DOWN

Button will begin to ﬂash.

1.7 Press and release the DOWN Button.

The door will travel to the programmed

DOWN position. Programming is

complete.

* If the garage door opener lights are ﬂashing 5 times during the steps for Program the Travel, the programming has timed out. If the garage door opener lights are ﬂashing 10 times during the steps for

Program the Travel, the safety reversing sensors are misaligned or obstructed. When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote

control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat the steps for Programming the Travel.

Adjustment

3.2 Press the remote control push button

to close the door. The door will not

move more than an inch (2.5 cm), and

the garage door opener lights will ﬂash

10 times.

Test the Protector System®

Synchronize the Door Control

3.1 Open the door. Place the garage door

opener carton in the path of the door. The garage door opener will not close from

a remote control if the LED in either safety

reversing sensor is off (alerting you to the fact

that the sensor is misaligned or obstructed).

If the garage door opener closes the door when

the safety reversing sensor is obstructed (and

the sensors are no more than 6 inches [15 cm]

above the ﬂoor), call for a trained door systems

technician.

2.1 With the door fully open, place a

1-1/2 inch (3.8 cm) board (or a 2x4 laid

ﬂat) on the ﬂoor, centered under the

garage door.

Test the Safety Reversal System

2.2 Press the remote control push button

to close the door. The door MUST

reverse when it makes contact with the

board.

If the door stops and does not reverse on the

obstruction, increase the down travel (refer to

Adjustment Step 1).

Repeat the test. When the door reverses upon

contact with the 1-1/2 inch board, remove the

board and open/close the door 3 or 4 times to

test the adjustment.

If the test continues to fail, call a trained door

systems technician.

Without a properly installed safety reversal

system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by

a closing garage door.

• Safety reversal system MUST be tested

every month.

• After ANY adjustments are made, the

safety reversal system MUST be tested.

Door MUST reverse on contact with 1-1/2"

high (3.8 cm) object (or 2x4 laid ﬂat) on

the ﬂoor.

Without a properly installed safety reversing

sensor, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by

a closing garage door.

To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar. Each

press of the push bar will activate the garage door opener.

Otros manuales para 050DCTWFLK

Tabla de contenidos

Otros manuales de Receptor de Chamberlain

Chamberlain

Chamberlain 955D Manual de usuario

Chamberlain

Chamberlain 635LM - Sears LiftMaster Chamberlain Manual de usuario

Chamberlain

Chamberlain PPWR Manual de usuario

Chamberlain

Chamberlain LiftMaster PROFESSIONAL 635-315LM Manual de usuario

Chamberlain

Chamberlain 050DCTB Manual de uso y cuidado

Chamberlain

Chamberlain LiftMaster Professional CPWR3 Manual de usuario

Chamberlain

Chamberlain LiftMaster Star250 Manual de usuario

Chamberlain

Chamberlain Liftmaster ULTRX900R Manual de usuario

Chamberlain

Chamberlain 1025 Manual de usuario

Chamberlain

Chamberlain 050DCTWFLK Manual de usuario

Chamberlain

Chamberlain LiftMaster 423LM Manual de usuario

Chamberlain

Chamberlain LiftMaster 422LM Manual de usuario

Chamberlain

Chamberlain LiftMaster 312HMC Manual de usuario

Chamberlain

Chamberlain CHAMBERLAIN 635LM Manual de usuario

Chamberlain

Chamberlain Ultra RX ULTRX900R Manual de usuario

Chamberlain

Chamberlain TRICODE TCG2 Manual de usuario

Chamberlain

Chamberlain 955D Manual de usuario

Chamberlain

Chamberlain PPWR Manual de usuario

Chamberlain

Chamberlain 955CB Manual de usuario

Chamberlain

Chamberlain 8003EV Manual de usuario

Chamberlain

Chamberlain 050DCTBMC Manual de usuario

Chamberlain

Chamberlain TRICODE TCR2 DUAL Manual de usuario

Chamberlain

Chamberlain TriCode TCG1 Manual de usuario

Chamberlain

Chamberlain 045DCT Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario