Central Pneumatic 46446 Manual de usuario

4848

48 PiePie

PiePie

Piecc

ceses

eses

es Pneumatic TPneumatic T

Pneumatic TPneumatic T

Pneumatic Tool Kitool Kit

ool Kitool Kit

ool Kit

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

withouttheexpress written consent of Harbor FreightTools.

For technical questions and replacement parts, please call 1-800-444-3353

46446

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 2

:emaNlooThcnerWtcapmIriA"2/1

:noitcurtsnoC gnisuoHmunimulAtsaC stnenopmoCleetS :evirD dradnatS"2/1erauqS elbisreveR

:euqroTmumixaM.sbl.tf032:yticapaCtloB"8/5

:erusserPgnitarepOISP09:noitpmusnoCriAISP09@MFC5

:deepSgnitarepOXAMMPR000,7:ylppuSriATPN81-"4/1

:snoisnemiDllarevOH"4/3-7xW"4/3-2xL"8/3-7:thgieWteN.SBL09.4

:emaNlooTllirDriAelbisreveR"8/3

:noitcurtsnoC ydoBmunimulA stnenopmoCleetShtiw :epyTreggirT elbairav-noN reveLesreveRhtiw

:kcuhCyeKhtiw"8/3:gniraeG epyTyratenalPelpitluM sgniraeBllaBhtiw

:erusserPgnitarepOXAMISP09:noitpmusnoCriAISP09@MFC6

:deepSgnitarepO )drawrof(MPR055,1 )esrever(MPR054,1 :ylppuSriATPN81-"4/1

:snoisnemiDllarevOH"8/1-6xW"8/5-1xL"2/1-7:thgieWteN.SBL07.2

:emaNlooTrednirGeiDriA"4/1

:noitcurtsnoC dnamunimulAdehsiloP leetSdetalPcniZkcalB :evirD gnidulcniepyTtelloC stelloc"4/1dna"8/1

:daerhTeldnipShctiPmm0.1xmm61:gniraeBeldnipSgniraeBllaBdedleihSlluF

:erusserPgnitarepOXAMISP09:noitpmusnoCriAISP09@MFC6

:deepSgnitarepOXAM000,32:ylppuSriATPN81-"4/1

:snoisnemiDllarevOW"8/3-2xL"4/3-6:thgieWteN.SBL52.1

:emaNlooTrednaSriAnoitcAlauD"6

:noitcurtsnoC ydoBmunimulAtsaC hgiHdenedraH&denihcaMhtiw leetSnobraC :daPgnidnaS retemaiD"6 daPdekcaBevisehdA )dedulcniton(

:daerhTeldnipSIPT42-"61/5:ylppuSriATPN81-"4/1

:erusserPgnitarepOXAMISP09:noitpmusnoCriAISP09@MFC11

:deepSgnitarepOMPR000,01:rotalugeRbonKnruTdelrunK

:snoisnemiDllarevOH"8/3-5xW"4/3-2xL"8/5-8:thgieWteN.SBL01.4

:emaNlooTremmaHtcapmIriAmm051

:noitcurtsnoC ydoBmunimulAtsaC hgiHdenedraH&denihcaMhtiw leetSnobraC :gnirpSleetSgnirpSnobraChgiH

:noisnemiDlesihCslesihCmm01dradnatS:ylppuSriATPN81-"4/1

:erusserPgnitarepOXAMISP09:noitpmusnoCriAISP09@MFC4

:deepSgnitarepO)etuniMrepswolB(MPB005,4:rotalugeRbonKnruTdelrunK

:snoisnemiDllarevOH"8/1-6xW"2xL"6:thgieWteN.SBL07.2

Specifications

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 3

Included Accessories

Accessory Specifications:

When unpacking, check to make sure the listed parts are included. If any parts

are missing or broken, please call Harbor FreightTools at the number on the cover

of this manual.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING:Whenusing tool,basicsafetyprecautions shouldalwaysbe followed

to reduce the risk of personal injury and damage to equipment.

Read all instructions before using these tools!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in

damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not

use electrically powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of children.

sgnittiFriAelaM)5(stnioPrednirGenotSdetnuoM)01(eldnaHnoisnetxEtcapmI"5)1(launaMs'renwO)1(

stiBlesihC)4(retpadA"8/3ot"2/1)1(stiBrevirD)4(stekcoStcapmI)01(

yeKxeHmm4)1(sehcnerWrennapS)2(esaCgniyrraCcitsalP)1(

:sepyTlesihC

tnioPlesihC lesihCtalF evoorG-V gniraehS

tiBrevirD :seziS

revirDdettolS"23/5 revirDdettolS"4/1 spillihP2# spillihP3#

:seziStekcoStcapmI ,"61/11,"8/5,"61/9,"2/1,"61/7 "1,"61/51,"8/7,"61/31,"4/3

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 4

5. Use the right tool for the job.Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. It will do the job better

and more safely at the rate for which it was intended. Do not modify this

tool and do not use this tool for a purpose for which it was not intended.

6. Dress properly while working. Protect your skin from accidental abrasion

burnsbywearing tough long sleeves and safety gloves. Donotwearloose

clothing or jewelry as they can be caught in moving parts. Protective,

electricallynon-conductive clothes andnon-skidfootwearare recommended

whenworking. Wearrestrictivehair covering to contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety

gogglesandfullface shield when using this tool. WearanANSIapproveddust

maskorrespiratorwhenworkingaroundmetal,wood,andchemicaldustsandmists.

8. Do not overreach. Keep proper footing and balance at all times. Do not

reachoveror across running machines.

9. Maintain tools with care. Keep tools clean and in good condition for better

andsafer performance. Follow instructionsforlubricatingand changing

accessories.Inspecttoolfittingsandhosesperiodicallyand,ifdamaged,have

them repaired by an authorized technician. The handles must be kept clean,

dry, and free from oil and grease at all times.

10. Disconnect power.Disconnect from air pressure source when not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting

wrenchesareremovedfromthetoolormachineworksurfacebeforeconnectingit.

12. Avoid unintentional starting. Be sure the throttle lever is in the Off position

when not in use and before attaching to pressure source. Do not carry any

tool with your hand on the throttle lever, whether it is attached or not.

Disconnect the air hose from the tool when not in use.

13. Stay alert. Watch what you are doing, use common sense. Do not operate

any tool when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate

properly and perform its intended function.Check for alignment and binding

of moving parts; any broken parts or mounting fixtures; and any other

condition that may affect proper operation.Any part that is damaged should

be properly repaired or replaced by a qualified technician.Do not use the tool

ifthethrottleleverdoes not function properly.

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 5

15. Guard against electric shock when working on electrical equipment,

such as your air compressor.Prevent body contact with grounded surfaces

suchaspipes,radiators,ranges,and refrigerator enclosures.

16. Replacement parts and accessories. Whenservicing, use onlyidentical

replacement parts.Use of any other parts will void the warranty. Only use

accessoriesintendedforusewith this tool. Approved accessories are

availablefromHarborFreightTools.

17. Do not operate tool if under the influence of alcohol or drugs. Read

warninglabelsonprescriptions to determine if your judgment or reflexes are

impaired while taking drugs. If there is any doubt, do not operate the tool.

18. Use proper size and type air pressure line and fittings. The recommended

airlineshoulddelivernomorethan90psi.

Recommended air inlet size is 1/4”- 18 NPT, using a 3/8” air hose.

19. Maintenance. For your safety, service and maintenance should be performed

regularlybyaqualified technician.

20. You should maintain a proper regulator and moisture trap in your air

line at all times.

21. Do not increase the air pressure to the tool beyond 90 PSI. This may

damagethe tool, or cause personal injury.

WARNING: Some dust created by power sanding,sawing,grinding,drilling,

and other construction activities, contain chemicals known [to the State of

California] to cause cancer,birth defects or other reproductive harm. Some

examples of these chemicals are:

* Lead from lead-based paints

* Crystalline silica from bricks and cement or other masonry products

* Arsenic and chromium from chemically treated lumber

(California Health & Safety Code 25249.5,

et seq.

)

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 6

Operation

1. Install one of the Standard 1/4” Male Fittings to the Air Inlet of each tool. First

wrapthethreadedportion of the Fitting with pipe thread seal tape before

threading it into the Air Inlet.Tighten securely.

2. Attach a standard quick connector (not included) to your air pressure source

hose.Then attach the air hose to theTool.

NOTE: If you are not using an automatic in-line oiler, add a few drops of pneumatic

oil to the Air Inlet before attaching the air hose. Add a few more drops of oil

afterevery hour of continualuse.

3. Set the air pressure regulator at 90 psi.

WARNING:DO NOT INCREASETHE AIR PRESSURE to the tool beyond 90

PSI.This may damage the tool, or cause personal injury.

4. Check the air line and its connections for air leaks. Make note of these, and

repairthembeforeusingthistool.

CAUTION: Turnoffyour air compressor and disconnect theairpressurehose

beforechangingattachmentsormakinganyadjustmentstothesetools. Severe

injuryorpropertydamagemay otherwise result.

Direction Controller (25)

Pneumatic

Tool

NOTE:Werecommend the use of in-line filter, regulator, and oilerinany

compressedairsystem using tools purchased from Harbor FreightTools.Please

refer to the schematic below for a suggested system set up.These components

are not included in this kit, but are available from Harbor FreightTools.

Note:Performanceofthesetoolsmayvarydependingonvariationsinlocalairpressure.

Warning:The warnings,cautions,and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may occur. It

mustbe understoodby theoperator thatcommon senseand cautionare factors

which cannot be built into this product, but must be supplied by the operator.

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 7

1/2” Air Impact Wrench

OPERATION

NOTE: Part numbers in this section refer to the Parts List on page 8, and Assembly

Drawing on page 9.

Your Impact Wrench

features an Air Regulator (37),

allowingyou to varytheamount of

torque exerted on the nut or bolt

you are working on. Setting “1” is

the lowest setting, and is

recommendedforsmallernutsand

bolts. Setting “4” is the highest

setting and provides the most

torqueand speed.

Loosening

1. Attach the correct size socket to the Anvil (8).

2. Set the compressor’s pressure regulator to 90 PSI. Do not set the outlet

regulatorof the compressor above90PSI.

3. Connect the Impact Wrench to the air compressor’s hose. If leaking is

detected,disconnecttheairhoseandrepairbefore use.

4. Place the socket over the nut to loosen.

5. Pressthe ReverseValve (44) in from the area above theTrigger (29) so that

the ReverseValve protrudes out the back of the Housing.Grip the Impact

Wrench firmly. Press the Trigger to start the Impact Wrench.

Caution: Before starting work, check the rating of the nut or bolt to be sure

it can withstand the working torque of the Impact Wrench.

6. If the Impact Wrench cannot loosen the nut, DO NOT raise the outlet pressure

oftheaircompressor.

7. If the Impact Wrench’s Air Regulator is set on a low setting, you may raise the

setting and try again. If the Impact Wrench’s Air Regulator is already set on

the “4” setting, do not continue attempts to loosen the nut with the Impact

Wrench. Use other appropriate tools and methods to loosen the nut.

8. Whenthenutisremoved,stoptheImpactWrenchbyreleasingtheTriggerand

removetheImpactWrenchfromthenut. Removethenutfromthesocketifneeded.

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 8

Tightening

The working torque of the Impact Wrench is 230 foot/lbs. Make sure the nut or

bolt you are using the Impact Wrench to tighten can withstand the rated torque.

1. Tighten the nut on as far as you can by hand.

2. Pressthe ReverseValve forward so it protrudes out the front of the Housing.

Place the socket on the nut. Press the Trigger to start the Impact Wrench.

3. If the Impact Wrench stalls while tightening, DO NOT raise the outlet pressure

oftheair compressor above 90 PSI.

4. If the Impact Wrench’s Air Regulator is set on a low setting, it may be raised

before you try again. If the nut will not tighten at the maximum setting, do not

continue attempts to tighten the nut. Use other appropriate tools and

methods to tighten the nut.

5. When the nut has been tightened, remove the Impact Wrench and socket. Do

notovertighten.

6. If available, check the recommended torque specifications for the nut. You

should use a torque wrench to torque the nut after using the Impact Wrench.

1/2” Air Impact Wrench Parts List

#traPnoitpircseD#traPnoitpircseD

1rotcetorPrebbuR32)4(wercS

2laeSliO42revoCrebbuR

3gnisuoH52niP

4wercS62niP

5gnihsuB72)2(wercS

6telloClivnA82revoCrelffuM

7gniR"O"7P92reggirT

8livnA03niPreggirT

9niPremmaH13desunU

01goDremmaH23desunU

11maCevirD33wercS

21egaCremmaH43wercSteS

31)2(gniraeB100653gnirpS

41desUtoN63gniR"O"8P

51etalPtnorF73rotalugeR

61)6(edalBrotoR83taeSevlaV

71rotoR93regnulPevlaVelttorhT

81rednilyC04llaB

91etalPdnE14gnirpS

02teksaG24neercShtiwtelnI

12revoCraeR34eveelSevlaV

22)4(rehsaW5m44evlaVesreveR

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 9

1/2” Air Impact Wrench Assembly Diagram

NOTE: Some parts are listed and shown forillustrationpurposes only and are not

availableindividuallyasreplacement parts. Some parts are available only as partof

an assembly.

Brought to You by www.snapwhole.com

SKU 46446

For technical questions and replacement parts, please call 1-800-444-3353

Page 10

3/8” Reversible Air Drill

OPERATION

NOTE: Part numbers in this section refer to the Parts List on page 11 and the

Assembly Drawing on page 12.

1. Settheairpressureregulatorat

90 psi.

WARNING: Do not exceed the

recommended pressure of 90 psi.

Damage to your tool, and possible

personal injury may result.

2. Check the air line and its

connections for air leaks. Make

note of these, and repair them before using this tool.

NOTE: Turnoffyour air compressor and disconnecttheairpressure hose before

changing bits or making any adjustments to this tool. Severe injury or property

damagemayotherwise result.

WARNING:Thistoolgeneratesconsiderable

torque when in use. Always hold the tool with

bothhandswhenusing,andbraceyourselfto

resistthe torquewhichwill bedeliveredto the

workpiece.

3.Select the appropriate sizedrillbit(not

included)foryourneeds.TheChuckmaybe

openedand closed using theChuckKey (see

photo).TurntheChuckKeycounterclockwise

to open, and clockwise to close the Chuck.

4.Insert the base of the drill bit into the

Chuck (16a). With the bit in place, tighten

the Chuck with the Chuck Key until the bit is securely held.

5. Move the Direction Switch (30a) to the LEFT to drill clockwise, move the

DirectionSwitch(30a)totheRIGHTtodrillcounterclockwise.NOTE: Inmost

cases, drill bits are designed to bore into the work material turning clockwise,

andtoreverseoutoftheworkmaterialbyturning counterclockwise.

6. Place the point of the drill bit at the spot you wish to drill. When it is safe to do

so, squeeze the Trigger (24a). The Drill will begin to operate, and the drill bit

will begin to drill into the work material. Drill until you have reached the desired

depth.ReleasetheTrigger (24a) to cease operation of the drill.

Using the Chuck Key

Brought to You by www.snapwhole.com

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Central Pneumatic

Central Pneumatic

Central Pneumatic Contractor 46365 Manual de usuario

Central Pneumatic

Central Pneumatic CENTRALPNEUMATIC 98580 Instrucciones de montaje

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 68128 Manual de instalación

Central Pneumatic

Central Pneumatic 66874 Manual de instalación

Central Pneumatic

Central Pneumatic 60801 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 68426 Manual de usuario

Central Pneumatic

Central Pneumatic 66886 Manual de instalación

Central Pneumatic

Central Pneumatic 98898 Manual de instalación

Central Pneumatic

Central Pneumatic 65902 Manual de instalación

Central Pneumatic

Central Pneumatic 94802 Manual de usuario

Central Pneumatic

Central Pneumatic 95098 Manual de usuario

Central Pneumatic

Central Pneumatic 65706 Manual de instalación

Central Pneumatic

Central Pneumatic Earthquake 65159 Manual de instalación

Central Pneumatic

Central Pneumatic 99792 Manual de instalación

Central Pneumatic

Central Pneumatic 95801 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 167 Manual de usuario

Central Pneumatic

Central Pneumatic 54753 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 47214 Manual de instrucciones original

Central Pneumatic

Central Pneumatic 68423 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor 90399 Manual de usuario

Central Pneumatic

Central Pneumatic 92849 Manual de usuario

Central Pneumatic

Central Pneumatic 68018 Manual de instalación

Central Pneumatic

Central Pneumatic 36567 Manual de usuario

Central Pneumatic

Central Pneumatic 54700 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual