Central Pneumatic 96068 Manual de instalación

12 VOLT HIGH VOLUME 100 PSI

AIR COMPRESSOR

Model

96068

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of Harbor

Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve-

ments, actual product may differ slightly from the product described herein. Tools required for assembly

and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 10g

Page 2SKU 96068 For technical questions, please call 1-800-444-3353.

SPECIFICATIONS

Electrical Requirements 12 VDC / 14 Amps

Power Cord Type: 18 AWG x 2 C x 121” Long

Power Plug Type: Cigarette Lighter Adapter Plug

Fuse Type: 15 Amp/250V

Power Switch Type: ON/OFF Rocker Button

Equipped with Overload Protection

Maximum Working Pressure 100 PSI

Pump Style Single Cylinder

Maximum Continuous

Working Time

12 Minutes

Recommended ON/OFF

Cycle Time

12 Minutes On / 30 Minutes Off

Air Gauge 0 to 100 PSI / 0 to 7 kg/cm2

Air Flow Capacity 0.88 GP/Minute (25 L/Minute)

Air Hose Diameter 5/16”

Overall Dimensions 6-5/8” L x 2.83” W x 5-1/4” H

Weight 3.5 Lb.

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, oper-

ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES AND PRECAUTIONS

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, re, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit.1. Cluttered benches and dark areas invite

accidents.

Do not operate air compressors in explosive atmospheres, such as in the2.

presence of ammable liquids, gases, or dust. Air Compressors create sparks

which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating an air tool.3.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed. Children

should not be allowed in the work area.

Page 3SKU 96068 For technical questions, please call 1-800-444-3353.

PERSONAL SAFETY

Stay alert. Watch what you are doing, and use common sense when operat-1.

ing an air tool. Do not use an air tool while tired or under the inuence of

drugs, alcohol, or medication. A moment of inattention while operating air tools

may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.2.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure the Power Switch (4) is in its “OFF” posi-3.

tion, all pressure is safely released, and the unit is unplugged before moving

the Compressor and before performing any service, maintenance, or cleaning

procedures on the unit.

Remove adjusting keys or wrenches before turning the Compressor on.4. A

wrench or a key that is left attached to a rotating part of the machine may result in

personal injury.

Do not overreach. Keep proper footing and balance at all times.5. Proper footing

and balance enables better control of the air tool in unexpected situations.

6. Use safety equipment. Always wear eye protection. Always wear ANSI-

approved safety impact goggles and heavy duty safety gloves during use.

TOOL USE AND CARE

Do not force the tool. Use the correct tool for your application.1. The correct

tool will do the job better and safer at the rate for which it is designed.

Do not use the Compressor if the Compressor’s Power Switch (4) does not2.

turn it on or off. Any tool that cannot be controlled with its Power Switch is dan-

gerous and must be replaced.

Store idle tools out of reach of children and other untrained persons.3. Tools

are dangerous in the hands of untrained users.

Maintain tools with care.4. Properly maintained tools are less likely to bind and are

easier to control. Do not use a damaged tool. Tag damaged tools “Do not use”

until repaired.

Check for misalignment or binding of moving parts, breakage of parts, and any5.

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your6.

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

Page 4SKU 96068 For technical questions, please call 1-800-444-3353.

SERVICE

Tool service must be performed only by qualied repair personnel. 1. Service or

maintenance performed by unqualied personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instruc-2.

tions in the “Inspection, Maintenance, And Cleaning” section of this manual.

Use of unauthorized parts or failure to follow maintenance instructions may create

a risk of electric shock or injury.

SPECIFIC SAFETY RULES AND PRECAUTIONS

CAUTION!1. Your Warranty is voided if:

Youa. drop the Air Compressor. Always lift the Air Compressor using its

Handle (52).

DANGER! This Air Compressor is NOT equipped and should not be used2.

“as-is” to supply breathing air. For any application of air for human consump-

tion, you must t the Air Compressor with suitable in-line safety and alarm equip-

ment (not included). This additional equipment is necessary to properly lter and

purify the air to meet minimal specications for Grade D breathing as described

in Compressed Gas Association Commodity Specication G 7.1-1966, OSHA 29

CFR 1910. 134, and/or Canadian Standards Associations (CSA). In the event the

Air Compressor is used for the purpose of breathing air application and proper in-

line safety and alarm equipment is not simultaneously used, existing warranties

are void, and Harbor Freight Tools disclaims any liability whatsoever for any loss,

personal injury, or damage.

Maintain labels and nameplates on the Air Compressor.3. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replace-

ment.

Always use a tire pressure gauge to check the actual pressure in the item4.

inated.

Do not use this Compressor continuously for over 12 minutes.5. Allow the

Compressor to cool approximately 30 minutes after inating an item.

Make sure all inatable items used with the Air Compressor are inated to 6.

the appropriate capacity. Do not inate any item over or under its manufacturer’s

recommended PSI rating.

Inatable items constructed of soft materials 7. (balls, beach toys, air mattresses,

rubber rafts, etc.) usually will not show the manufacturer’s recommended air pres-

sure. Take care not to over-inate the object.

Avoid burns.8. After several minutes of use, the Compressor will become hot to the

touch. Always wear heavy duty safety gloves when using the Compressor.

Page 5SKU 96068 For technical questions, please call 1-800-444-3353.

Avoid injury.9. Never direct the Air Nozzle (57) at people or animals.

Make sure the Air Compressor is located on a at, level, sturdy surface ca-10.

pable of supporting the weight of the Compressor and any additional tools

and equipment.

Industrial applications must follow OSHA guidelines.11.

Never leave the Air Compressor unattended when it is plugged in and running.12.

Turn off the Compressor, and unplug the unit before leaving.

Do not allow children and other unauthorized people to handle or play with13.

the Air Compressor.

Do not modify the factory set pressure shutoff or startup switches.14. This tool will

do the work better and safer at the speed and capacity for which it was designed.

Never point the Air Nozzle (57) at people or animals.15.

16. WARNING! The brass components of this product contain lead, a chemical

known to the State of California to cause birth defects (or other reproductive harm).

(California Health & Safety code § 25249.5, et seq.)

17. WARNING! People with pacemakers should consult their physician(s) before

use. Electromagnetic elds in close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

18. WARNING! The warnings and precautions discussed in this manual

cannot cover all possible conditions and situations that may occur. It must

be understood by the operator that common sense and caution are factors

which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

UNPACKING

When unpacking, check to make sure all parts shown on the Parts List are included.

If any parts are missing or broken, please call Harbor Freight Tools at the number

shown on the cover of this manual (and at the bottom of each page) as soon as

possible.

REV 10g

Page 6SKU 96068 For technical questions, please call 1-800-444-3353.

OPERATING INSTRUCTIONS

Power

Switch (4)

Cigarette

Lighter

Adapter

(1)

Air

Nozzle

(57)

Pressure

Meter

(49)

FIGURE A

To Inate Automotive Tires:

Place the Air Compressor on a at, 1.

level, dry surface.

2. Remove the valve cap from the

valve stem of a

tire. Thread on

the Air Nozzle

(57) to the tire

stem. (See

Figure B.)

Plug the Cigarette Lighter Adapter3.

(1) into the vehicle’s cigarette lighter

socket. (See Figure C.)

FIGURE C

CIGARETTE LIGHTER ADAPTER (1)

Caution: Always start the vehicle’s

engine prior to operating the Air

Compressor so as to not deplete

the vehicle’s battery.

4. Turn the Air Compressor’s Power

Switch (4) to

its “ON” posi-

tion. (See

Figure D.)

The Pressure Meter (49) is located5.

on top of the Air Compressor. The

maximum air pressure this unit will

produce is 100 PSI. Do not inate

the air pressure beyond the tire

manufacturer’s ination rating.

To obtain an accurate air pressure

reading, turn off the Air Compressor

when the desired pressure is indi-

cated on the gauge. (See Figure

A.)

When nished, turn the Power 6.

Switch (4) to its “OFF” position. Re-

mover the Air Nozzle (57) from the

vehicle’s tire valve stem. Replace

the valve cap. Then, disconnect

the Cigarette Lighter Adapter (1)

from the vehicle’s cigarette lighter

socket.

FIGURE B

OFF ON

FIGURE D

REV 10g

Page 7SKU 96068 For technical questions, please call 1-800-444-3353.

To Inate Balls, Toys, Air Mattresses, Rubber Rafts, Etc.:

The compressor comes with three nozzles for inating a variety of items. Thread 1.

on the desired nozzle onto the Air Nozzle (57). Insert the nozzle into the item you

want to inate then turn on the Air Compressor, and inate the object. Do not

over-inate.

When nished, turn the Power Switch (4) to its “OFF” position. Remove the nozzle 2.

from the inated object. Then, disconnect the Cigarette Lighter Adapter (1) from

the vehicle’s cigarette lighter socket. (See Figures A and B)

INSPECTION, MAINTENANCE, AND CLEANING

WARNING!1. Make sure the Power Switch (4) of the Air Compressor is in its

“OFF” position and the unit is unplugged from the vehicle’s cigarette lighter socket

before performing any inspection, maintenance, or cleaning procedures.

Before each use,2. inspect the general condition of the Air Compressor. Check for

loose screws, misalignment or binding of moving parts, cracked or broken parts,

damaged electrical wiring, loose air ttings, and any other condition that may affect

the safe operation of the Compressor. If abnormal noise or vibration occurs, have

the problem corrected before further use. Do not use damaged equipment.

To clean,3. wipe with a clean, damp cloth and a mild detergent. Then dry. Do not

use solvents. Do not immerse the unit in liquids.

To replace the Fuse (58),4. unscrew and remove the cap on the Cigarette Lighter

Adapter (1). Remove the old Fuse, and replace with a new Fuse (type: 15 Amp).

Then, screw the cap back onto the Cigarette Lighter Adapter. (See Figure C)

CAP

GLASS FUSE (58)

CIGARETTE LIGHTER ADAPTER (1)

FIGURE C

CAUTION! All maintenance, service, or repairs not mentioned in this5.

manual must only be performed by a qualied service technician.

Page 8SKU 96068 For technical questions, please call 1-800-444-3353.

PARTS LIST

Part Description Part Description Part Description

1 Cigarette Lighter Adapter 21 Bearing (608Z) 41 Seal Ring

2 Cord 22 End Cover 42 Air Exhaust Slice

3 Screw (3 x 25) 23 Inner Hex Screw (4 x 8) 43 Rivet

4 Power Switch 24 Shockproof Pad 44 Seal Ring

5 Rear Cover 25 Air Intake Cover 45 Cylinder Cover

6 Shockproof Pad 26 Filter Mesh 46 Spring Washer (4mm)

7 Connection Cap 27 Screw (3 x 10) 47 Screw (4 x 35)

8 Screw (4 x 102) 28 Front Cover 48 Support Ring

9 Spring Washer (4mm) 29 Offset Shaft 49 Pressure Meter

10 Washer (4mm) 30 Offset Wheel 50 Protective Sleeve

11 Cord Sleeve 31 Bearing (626Z) 51 Air Outlet Tube (8 x 114)

12 Overload Protector 32 Crank 52 Handle

13 Connection Wire 33 Piston Ring 53 Air Outlet

14 Motor Rear Cover 34 Press Ring 54 Quick Connector

15 Brush Holder 35 Air Intake Slice 55 Air Hose (8 x 1500)

16 Motor Housing 36 Rivet 56 Lock Spring

17 Bearing (608Z) 37 Cylinder Liner 57 Air Nozzle

18 Spring Washer 38 Radiation Cover 58 Glass Fuse (15 Amp)

19 Rotor 39 Seal Ring 59 Needle Nozzle

20 Spring Washer 40 Cover 60 (2) Inator Nozzle

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKESANY REPRESENTATION OR WARRANTY OFANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.

THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

Compressor will not start. Cigarette Lighter Adapter (1) not1.

securely inserted in vehicle’s cigarette

lighter socket.

Power Switch (4) not on.2.

Vehicle battery not fully charged.3.

Blown Compressor Fuse.4.

Blown automotive fuse.5.

Insert Cigarette Lighter Adapter (1) securely.1.

Turn Power Switch (4) ON.2.

Charge vehicle battery.3.

Replace Fuse.4.

Check automotive manual and replace blown5.

fuse.

Low pressure. Loose connection(s).1. Make sure all connections are tight.1.

Overload Protector trips. Continuous use too long.1. Do not use unit continuously for over 121.

minutes. Allow 30 minutes for unit to cool

down after each use.

REV 10g

Page 9SKU 96068 For technical questions, please call 1-800-444-3353.

ASSEMBLY DIAGRAM

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 10SKU 96068 For technical questions, please call 1-800-444-3353.

LIMITED 1 YEAR / 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that for a period

of one year from date of purchase that the tank is free of defects in materials and work-

manship (90 days if used by a professional contractor or if used as rental equipment).

Harbor Freight Tools also warrants to the original purchaser, for a period of ninety days

from date of purchase, that all other parts and components of the product are free from

defects in materials and workmanship. This warranty does not apply to damage due

directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations out-

side our facilities, normal wear and tear, or to lack of maintenance. We shall in no event

be liable for death, injuries to persons or property, or for incidental, contingent, special

or consequential damages arising from the use of our product. Some states do not allow

the exclusion or limitation of incidental or consequential damages, so the above limitation

of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection veries the defect, we will either

repair or replace the product at our election or we may elect to refund the purchase price

if we cannot readily and quickly provide you with a replacement. We will return repaired

products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning

the product.

This warranty gives you specic legal rights and you may also have other rights

which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Tabla de contenidos

Otros manuales de Compresor de aire de Central Pneumatic

Central Pneumatic

Central Pneumatic 60638 Manual de usuario

Central Pneumatic

Central Pneumatic CentralPneumatic 69269 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 67698 Manual de usuario

Central Pneumatic

Central Pneumatic 61454 Manual de usuario

Central Pneumatic

Central Pneumatic PROFESSIONAL 99901 Manual de usuario

Central Pneumatic

Central Pneumatic 69667 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 60567 Manual de instrucciones original

Central Pneumatic

Central Pneumatic 67847 Guía del usuario

Central Pneumatic

Central Pneumatic 61615 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 42321 Manual de usuario

Central Pneumatic

Central Pneumatic 93271 Manual de usuario

Central Pneumatic

Central Pneumatic 95386 Manual de instalación

Central Pneumatic

Central Pneumatic 9592 Manual de usuario

Central Pneumatic

Central Pneumatic 60637 Guía del usuario

Central Pneumatic

Central Pneumatic 61489 Manual de usuario

Central Pneumatic

Central Pneumatic 45214 Manual de usuario

Central Pneumatic

Central Pneumatic 90385 Manual de usuario

Central Pneumatic

Central Pneumatic 61489 Guía del usuario

Central Pneumatic

Central Pneumatic 93351 Manual de usuario

Central Pneumatic

Central Pneumatic 93785 Manual de usuario

Central Pneumatic

Central Pneumatic 96469 Manual de instalación

Central Pneumatic

Central Pneumatic 98635 Manual de instalación

Central Pneumatic

Central Pneumatic 67696 Manual de instalación

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 47407 Manual de lista de piezas

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario