Central Pneumatic 42321 Manual de usuario

SKU 42321 For technical questions, please call 1-800-444-3353. Page 3

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

2. Do not operate compressors in explosive atmospheres, such as in the presence

of flammable liquids, gases, or dust. Compressors create sparks which may ignite

the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a compressor.

Provide barriers or shields as needed.

ELECTRICAL SAFETY

1. Grounded compressors must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter plugs.

Check with a qualified electrician if you are in doubt as to whether the outlet is

properly grounded. If the compressors should electrically malfunction or break down,

grounding provides a low resistance path to carry electricity away from the user.

2. Do not expose compressors to rain or wet conditions. Water entering an electric

motor will increase the risk of electric shock.

3. Do not abuse the Power Cord. Never use the Power Cord to pull the Plug from an

outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts.

Replace damaged Power Cords immediately. Damaged Power Cords increase the

risk of electric shock.

4. AN EXTENSION CORD MUST NEVER BE USED WITH THIS ITEM. Connecting

this item to an outlet through an extension cord MAY CAUSE ELECTRICAL

DAMAGE TO THE MOTOR and could present a FIRE HAZARD.

PERSONAL SAFETY

1. Stay alert. Watch what you are doing, and use common sense during use. Do not

use while tired or under the influence of drugs, alcohol, or medication. A moment

of inattention while operating may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

3. Avoid accidental starting. Be sure the Power Switch is turned off before plugging

in. Plugging in compressors with the Power Switch on, invites accidents.

4. Remove adjusting keys or wrenches before turning the compressor on. A wrench

or a key that is left attached to a rotating part of the compressor may result in personal

injury.

5. Do not overreach. Keep proper footing and balance at all times.

SKU 42321 For technical questions, please call 1-800-444-3353. Page 4

6. Use safety equipment. Always wear eye protection. Make sure you are wearing

your protective clothing, safety glasses with side shields and dust mask or air respirator,

if appropriate.

TOOL USE AND CARE

1. Do not force the compressor. Use the correct compressor for your application.

The correct compressor will do the job better and safer at the rate for which it is designed.

Never attempt to force the compressor to provide more pressure than it was designed

for.

2. Do not use the compressor if the Power Switch does not turn it on or turn it off.

Any compressor that cannot be controlled with the Power Switch is dangerous and

must be repaired or replaced.

3. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the compressor. Such preventive

safety measures reduce the risk of starting the compressor accidentally.

4. Keep idle compressors out of reach of children and other untrained persons.

Compressors are dangerous in the hands of untrained users.

5. Maintain compressors with care. Keep all components of this product clean and

dry. Do not use a damaged compressor. Tag damaged compressors “Do not use” until

repaired.

6. Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the compressor’s operation. If damaged,have the

compressor serviced before using. Many accidents are caused by poorly maintained

compressors.

7. Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one compressor may become hazardous when

used on another compressor.

SERVICE

1. Compressor service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

2. When servicing a compressor, use only identical replacement parts. Follow

instructions in the

“Inspection,Maintenance, And Cleaning”

section of this manual.

Use of unauthorized parts or failure to follow maintenance instructions may create a

risk of electric shock or injury.

SPECIFIC SAFETY RULES

1. CAUTION! Prior to its

first

use, and thereafter prior to each

subsequent

use, make

sure to fill the Air Compressor with a premium quality, 30 weight, non-detergent

oil to the specified level. Running the Air Compressor with no oil or with low oil will

SKU 42321 For technical questions, please call 1-800-444-3353. Page 5

cause damage to the equipment and void its warranty. Refer to the

“Operating

Instructions”

section for details on filling the Air Compressor with oil.

2. When filling the Air Compressor with oil, make sure to

unscrew

(do not pull) the

Oil Fill Cap to remove.

3. Use eye and ear protection. Always wear ANSI-approved safety impact eye goggles,

and ear plugs when using the Air Compressor.

4. Make sure all tools and equipment used with the Air Compressor are rated to the

appropriate air pressure capacity of the Air Compressor. Do not use any tool or

equipment that does not operate from 0-115 PSI. If necessary, check the owner’s manual

of the tool or equipment for its air pressure rating.

5. Always disconnect the Air Compressor from its electrical outlet, release any

remaining air pressure from the unit, and disconnect all pneumatic tools and

equipment from the unit, before performing any services or maintenance.

6. Avoid injury. Never direct the air jet at people or animals.

7. Inspect safety valve daily.If the safety valve is not working properly, tank pressure can

build up to dangerous levels. The tank could explode. For this reason, pull the ring on

the safety valve before each use and verify that it operates freely. Replace safety valve

if it does not operate freely.

Never remove or alter the factory sealed Safety Release Valve.

8. Do not attempt to readjust the automatic start and shutoff valves. Any change to

the automatic ON/OFF pressure levels will cause additional stress on the motor, which

may result in shortened motor life.

9. Drain the Air Compressor’s air tank every day. Do not allow moisture to build up

inside the Air Tank.

10. Do not unscrew the tank drain valve so that

more than

four threads are showing.

11. Avoid risk of tank explosion.

a) Avoid weakening of tank by draining condensation after each use.

b) Never modify tank by drilling holes, welding to it, or modifying it’s parts.

c) The tank is designed, and factory set, to operate within a specific pressure range.

For that reason, never make adjustments to, or substitute parts, to the compressor.

12. Avoid bodily injury from moving parts. The compressor cycles on automatically,

without notice. For this reason, always keep hands and arms away from compressor

parts when the unit is connected to electrical power. Always have compressor safety

guards in place before turning compressor on.

13. Use approved air hose. Never use plastic or PVC pipe (unless specified for Air

Compressors) to carry air under pressure. Regardless of its pressure rating, it can burst

under pressure. Use only metal pipe.

14. Never plug the power cord of this product into an electrical outlet while standing

on a wet or damp surface.

SKU 42321 For technical questions, please call 1-800-444-3353. Page 6

15. THIS AIR COMPRESSOR MAY REQUIRE A DEDICATED ELECTRICAL CIRCUIT

AS THE AMPERAGE DRAW UNDER FULL LOAD, COMBINED WITH USE OF ANY

OTHER ITEM, MAY OVERLOADYOUR CIRCUIT.

16. Always turn off the Air Compressor in the event of a power failure.

17. Performance of this Air Compressor may vary depending on variations in local

line voltage.

18. Maintain labels and nameplates on the Air Compressor. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

19. WARNING! People with pacemakers should consult their physician(s) before using

this product. Electromagnetic fields in close proximity to a heart pacemaker could cause

interference to or failure of the pacemaker.

20. WARNING! The brass components of this product contain lead, a chemical known

to the State of California to cause birth defects (or other reproductive harm). (California

Health & Safety code § 25249.5,

et seq.

)

21. WARNING! The warnings, precautions, and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may occur. It must be

understood by the operator that common sense and caution are factors which cannot

be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

SKU 42321 For technical questions, please call 1-800-444-3353. Page 7

Setup

Dipstick

Warning: Fill compressor with oil before using; running with NO OIL or with LOW OIL

will void the warranty. The optimal capacity of the oil reservoir is 7.8 ounces of oil.

The Dipstick is used to determine if oil is needed. Never operate the compressor without

sufficient oil. Use a 30 weight, non-detergent compressor oil. To check the oil:

1. Unscrew the Dipstick.

2. Check the level of the oil. There are two lines on the bottom of the Dipstick. The oil

level should be somewhere between the two lines, as high as possible.

3. Add oil through the Gauge’s hole as necessary, but do not overfill. Always use a high

grade oil specially designed for air compressors. Never mix oils of different types.

Never use a low quality oil which may not afford adequate lubrication.

4. Replace the Dipstick.

Install an Air Intake Filter and Hose (not included)

The filter and oiler (not supplied) are recommended but not mandatory for operation.

1. Remove and discard the plastic cap which covers the threaded hole at the top of the

Cylinder Case (B-6).

2. Screw the threaded part of the air filter assembly into the Cylinder Case until it is

firmly seated.

3. Connect the air tool, air hoses, filter, and oiler to the Compressor Air Output as

illustrated on the next page.

If the filter and oiler are not used, connect the air hose directly to the 1/4 inch NPT

barbed connector located at the Air Flow Valve (A-8). For easy connection or removal,

a quick coupler should be installed on the end of the air output.

Note: Use pipe thread seal tape on all threaded connections.

REV 08/01; 02/04

SKU 42321 For technical questions, please call 1-800-444-3353. Page 8

Operation

Caution: Prior to use, inspect the compressor or any damaged parts or unsafe condi-

tions. Make any necessary repairs before using again.

Turning Compressor On

1. Verify Tank Drain Valve (A-7) is closed.

2. Verify oil level is correct.

3. Verify that the Safety Valve (A-4) is operational.

4. Turn the Air Flow Valve (A-8) to the OFF position.

5. Plug the power cord into a electrical outlet with a grounding prong.

6. Turn the ON/OFF Switch Lever(A-5) down to turn on. Turn the Switch Lever up

to shut off.Allow the pressure to build up to at least 80 PSI before using air.

7. Open the Air Flow Valve (A-8) and check for air leaks.

The operation of the compressor is automatic, as controlled by the an internal pressure

switch. When the pressure drops below its operating range the compressor turns on.

When the pressure is above 115 PSI, the compressor shuts off.

Warning; The compressor may become very hot during operation. Do not touch the

cylinder area of the compressor, or allow flammable materials to come in contact with

the cylinder area.

Adjusting Pressure Gauge and Pressure Adjustment Screw

Caution:The Pressure Switch is adjustable but changes to the pressure levels are not

recommended; any change to the automatic ON/OFF pressure levels will cause addi-

tional stress on the motor which may shorten motor life.

Adjusting Air Output

1. When the Lever of the Air Flow Valve (A-8) is to the up or down position, the valve is closed.

When it is in the middle, it is open.

2. Turn the Air Flow Valve to the appropriate pressure.

Maintenance

Warning: Do not make any repairs, adjustments, or maintenance on the air compressor

unless it is disconnected from the electrical power and the tank pressure is released.

Maintenance should always be performed by a qualified technician.

1. Check the oil level before each use. If the oil is low, add some. If it is high, drain some

by removing the Drain Plug. Replace the oil once a year.

2. Check and clean the Air Filter (B-5) every 50 hours, or sooner if used in a dusty

environment. REV 02/04

SKU 42321 For technical questions, please call 1-800-444-3353. Page 9

3. Drain the air tanks after each use by opening the drain petcock or the Tank Drain Valve

(A-7). Leave open until the next use.

4. Clean compressor with a damp rag containing mild detergent and water. Do not use

flammable liquids or solvents.

Parts List “A”

#metInoitpircseDytQ

1-AylbmessArosserpmoC1

2-AeguaGerusserP1

3-ApirGrebbuR1

4-AevlaVytefaS1

5-AhctiwSFFO/NO1

6-AknaTriA2

-AevlaVniarDknaT1

8-AevlaVwolFriA1

9-AevlaVyaWenO1

01-AebuT1

11-AesaB1

21-AtooFrebbuR4

31-AtuNdnatloB.ae1

NOTE: Some parts are listed and shown for

illustration purposes only and are not available

individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM INTHIS

MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-

TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER

REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING

OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Tabla de contenidos

Otros manuales de Compresor de aire de Central Pneumatic

Central Pneumatic

Central Pneumatic 94724 Manual de usuario

Central Pneumatic

Central Pneumatic 67696 Manual de instalación

Central Pneumatic

Central Pneumatic 95370 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 93657 Manual de usuario

Central Pneumatic

Central Pneumatic 96068 Manual de instalación

Central Pneumatic

Central Pneumatic 67696 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 67847 Manual de instrucciones original

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 95499 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 67708 Manual de instalación

Central Pneumatic

Central Pneumatic 9592 Manual de usuario

Central Pneumatic

Central Pneumatic 95630 Manual de instalación

Central Pneumatic

Central Pneumatic 34844 Manual de usuario

Central Pneumatic

Central Pneumatic 99659 Manual de instalación

Central Pneumatic

Central Pneumatic 95275 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 67847 Guía del usuario

Central Pneumatic

Central Pneumatic 93271 Manual de instalación

Central Pneumatic

Central Pneumatic 21 Manual de usuario

Central Pneumatic

Central Pneumatic 93657 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 60637 Guía del usuario

Central Pneumatic

Central Pneumatic 93351 Manual de usuario

Central Pneumatic

Central Pneumatic 60567 Manual de instrucciones original

Central Pneumatic

Central Pneumatic 92097 Manual de usuario

Central Pneumatic

Central Pneumatic CentralPneumatic 68064 Manual de instalación

Central Pneumatic

Central Pneumatic 56101 Instrucciones de montaje

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario