Central Pneumatic 95630 Manual de instalación

COMPRESSOR AND

AIR BRUSH KIT

Model

95630

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read and understand tool labels and

manual. Failure to follow warnings could

result in DEATH or SERIOUS INJURY.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1‑800‑444‑3353.

Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 95630

SAVE THIS MANUAL

Keep this manual for the safety warnings

and precautions, assembly, operating,

inspection, maintenance and cleaning

procedures. Write the product’s serial number

in the back of the manual near the assembly

diagram (or month and year of purchase if

product has no number). Keep this manual

and the receipt in a safe and dry place for

future reference.

Safety Alert Symbol and Signal

Words

In this manual, on the labeling, and

all other information provided with

this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that follow

this symbol to avoid possible

injury or death.

DANGER indicates a

hazardous situation

which, if not avoided, will result

in death or serious injury.

WARNING indicates a

hazardous situation

which, if not avoided, could

result in death or serious injury.

CAUTION, used with

the safety alert

symbol, indicates a hazardous

situation which, if not avoided,

could result in minor or moderate

injury.

NOTICE is used to

address practices not

related to personal injury.

CAUTION, without the

safety alert symbol, is

used to address practices not

related to personal injury.

Symbol Denitions

Symbol Property or statement

PSI Pounds per square inch of pressure

CFM Cubic Feet per Minute ow

SCFM Cubic Feet per Minute ow at standard

conditions

NPT National pipe thread, tapered

NPS National pipe thread, straight

WARNING marking concerning Risk of

Eye Injury. Wear ANSI-approved safety

goggles with side shields.

Read the manual before set-up and/or

use.

WARNING marking concerning Risk of

Hearing Loss. Wear hearing protection.

WARNING marking concerning Risk

of Respiratory Injury. Wear NIOSH-

approved dust mask/respirator.

WARNING marking concerning Risk of

Explosion.

IMPOINSTRUCTIONS

INSTRUCTIONS PERTAINING

TO A RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY

TO PERSONS

WARNING – When using tools, basic

precautions should always be followed,

including the following:

Important Safety Instructions

Page 3For technical questions, please call 1‑800‑444‑3353.SKU 95630

General

a. To reduce the risks of electric shock,

re, and injury to persons, read all the

instructions before using the tool.

Work area

a. Keep the work area clean and well

lighted. Cluttered benches and dark

areas increase the risks of electric

shock, re, and injury to persons.

b. Do not operate the tool in explosive

atmospheres, such as in the presence

of ammable liquids, gases, or dust.

The tool is able to create sparks resulting

in the ignition of the dust or fumes.

c. Keep bystanders, children, and

visitors away while operating the tool.

Distractions are able to result in the loss

of control of the tool.

Electrical Safety

a. Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with grounded power tools.

Unmodied plugs and matching outlets

will reduce risk of electric shock.

b. Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your

body is grounded.

c. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric

shock.

d. Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep cord

away from heat, oil, sharp edges or

moving parts. Damaged or entangled

cords increase the risk of electric shock.

e. When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk

of electric shock.

f. If operating a power tool in a damp

location is unavoidable, use a Ground

Fault Circuit Interrupter (GFCI)

protected supply. Use of a GFCI

reduces the risk of electric shock.

Personal safety

a. Stay alert. Watch what you are

doing and use common sense when

operating the tool. Do not use the

tool while tired or under the inuence

of drugs, alcohol, or medication. A

moment of inattention while operating

the tool increases the risk of injury to

persons.

b. Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep hair, clothing, and gloves away

from moving parts. Loose clothes,

jewelry, or long hair increases the risk

of injury to persons as a result of being

caught in moving parts.

c. Avoid unintentional starting. Be

sure the Power Switch if off before

connecting to the air supply. Do not

carry the tool with your nger on the

Power Switch or connect the tool to the

air supply with the trigger pressed.

d. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enables

better control of the tool in unexpected

situations.

Page 4 For technical questions, please call 1‑800‑444‑3353. SKU 95630

e. Use safety equipment. A

dust mask, non-skid safety

shoes and a hard hat must be

used for the applicable

conditions. Wear heavy-duty work

gloves during use.

f. Always wear eye protection.

Wear ANSI-approved safety

goggles with side shields.

g. Always wear hearing

protection when using the

tool. Prolonged exposure to

high intensity noise is able to

cause hearing loss.

Tool use and care

a. Use clamps or another practical way

to secure and support the workpiece

to a stable platform. Holding the work

by hand or against the body is unstable

and can lead to loss of control.

b. Do not force the tool. Use the correct

tool for the application. The correct tool

will do the job better and safer at the rate

for which the tool is designed.

c. Do not use the tool if the Power

Switch does not turn the tool on or

off. Any tool that cannot be controlled

with the Power Switch is dangerous and

must not be used until repaired.

d. Disconnect the tool from the air

source before making adjustments,

doing tool maintenance, clearing

jams, touching the safety nosepiece,

leaving work area, loading, or

unloading the tool. Such precautionary

measures reduce the risk of injury to

persons.

e. Store the tool when it is idle out of

reach of children and other untrained

persons. A tool is dangerous in the

hands of untrained users.

f. Maintain the tool with care. A properly

maintained tool reduces the risk of

binding and is easier to control.

g. Check for misalignment or binding

of moving parts, breakage of parts,

and any other condition that affects

the tool’s operation. If damaged,

have the tool serviced before using.

Many accidents are caused by poorly

maintained tools. There is a risk of

bursting if the tool is damaged.

h. Use only accessories that are

identied by the manufacturer for

the specic tool model. Use of an

accessory not intended for use with the

specic tool model, increases the risk of

injury to persons.

Service

a. Tool service must be performed only

by qualied repair personnel.

b. When servicing a tool, use only

identical replacement parts. Use only

authorized parts.

SAVE THESE

INSTRUCTIONS.

Page 5For technical questions, please call 1‑800‑444‑3353.SKU 95630

SPECIFIC SAFETY S

1. Maintain labels and nameplates on the

tool. These carry important information.

If unreadable or missing, contact Harbor

Freight Tools for a replacement.

2. DANGER! This Air Compressor is

NOT equipped and should not be used

“as is” to supply breathing quality air.

For any application of air for human

consumption, you must t the Air

Compressor with suitable in-line safety

and alarm equipment (not included).

This additional equipment is necessary

to properly lter and purify the air to

meet minimal specications for Grade D

breathing as described in Compressed

Gas Association Commodity

Specication G 7.1-1966, OSHA 29 CFR

1910. 134, and/or Canadian Standards

Associations (CSA).

3. Make sure all tools and equipment

used with the Air Compressor are

rated to the appropriate capacity.

Do not use any tool or equipment that

operates above 58 PSI.

4. Drain the Air Compressor everyday.

Do not allow excessive moisture to build

up inside the Air Compressor. Do not

open the Water Drain Valve (23) with

more than 10 PSI of air pressure in the

Compressor.

5. Avoid injury. Do not direct compressed

air at people of animals. Do not direct

airow at eyes or ears.

6. Make sure the Air Compressor is

located on a at, level, sturdy surface

capable of supporting the weight of

the Compressor and any additional

tools and equipment.

7. Industrial applications must follow

OSHA guidelines.

8. Do not stand or sit on the Air

Compressor. Serious injury could result

if the Compressor is tipped.

9. Do not leave the Air Compressor

unattended when it is plugged in.

Turn off the Compressor and unplug

before leaving.

10. Do not move or transport the

Air Compressor if the unit is

under pressure.

11. Do not force the Air Compressor.

This tool will do the work better and safer

at the speed and capacity for which it

was designed.

12. This Air Compressor will

automatically shut off on overload

or under excessive heat. Should

this occur, turn the Power Switch (34)

to its “OFF” position. Wait until the

Air Compressor cools. Then turn the

Power Switch (34) to its “ON” position to

resume work.

13. Spray painting only. Do not use this Air

Compressor with gasoline, kerosene, or

any other ammable solvent.

14. Maintain a safe working environment.

Make sure there is adequate

surrounding workspace. Do not use

this product in a damp or wet location.

15. People with pacemakers should

consult their physician(s) before

using this product. Electromagnetic

elds in close proximity to a heart

pacemaker could cause interference to

or failure of the pacemaker. In addition,

people with pacemakers should adhere

to the following:

• Avoid operating power tools alone.

• Don’t use a power tool with the power

switch locked on.

• If powered via a power cord be certain

that the tool is properly grounded. A

Specic Safety Instructions

Page 6 For technical questions, please call 1‑800‑444‑3353. SKU 95630

ground fault interrupt (GFCI) system

is also a good precaution. This

inexpensive device is a good safety

measure because it prevents a sustained

electrical shock.

• Properly maintain and inspect all tools

before use to avoid electrical shock

16. Never leave the tool unattended when

it is plugged into an electrical outlet.

Turn off the tool, and unplug it from its

electrical outlet before leaving.

17. WARNING: The brass components of

this product contain lead, a chemical

known to the State of California

to cause birth defects (or other

reproductive harm). (California Health

& Safety code § 25249.5, et seq.)

18. WARNING: Some dust created by

power sanding, sawing, grinding,

drilling, and other construction

activities, contains chemicals

known [to the State of California] to

cause cancer, birth defects or other

reproductive harm. Some examples of

these chemicals are:

Lead from lead-based paints

Crystalline silica from bricks and cement

or other masonry products

Arsenic and chromium from chemically

treated lumber

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemicals: work in a well

ventilated area, and work with approved

safety equipment, such as those dust

masks that are specially designed to

lter out microscopic particles. (California

Health & Safety Code § 25249.5, et seq.)

19. Always maintain adequate ventilation,

especially when using solvent based

paints and during clean up.

SAVE THESE

INSTRUCTIONS.

Groun

ding

TO PREVENT ELECTRIC

SHOCK AND DEATH

FROM

INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualied electrician

if you are in doubt as to whether

the outlet is properly grounded.

Do not modify the power cord

plug provided with the tool.

Never remove the grounding

prong from the plug. Do not use

the tool if the power cord or plug

is damaged. If damaged, have it

repaired by a service facility

before use. If the plug will not t

the outlet, have a proper outlet

installed by a

qualied electrician.

Grounded Tools:

Tools with Three Prong Plugs

3‑Prong Plug and Outlet

1. Tools marked with “Grounding Required”

have a three wire cord and three prong

grounding plug. The plug must be

connected to a properly grounded outlet.

Grounding

Page 7For technical questions, please call 1‑800‑444‑3353.SKU 95630

If the tool should electrically malfunction

or break down, grounding provides a

low resistance path to carry electricity

away from the user, reducing the risk

of electric shock. (See 3‑Prong Plug

and Outlet.)

2. The grounding prong in the plug is

connected through the green wire inside

the cord to the grounding system in the

tool. The green wire in the cord must

be the only wire connected to the tool’s

grounding system and must never be

attached to an electrically “live” terminal.

(See 3‑Prong Plug and Outlet.)

3. The tool must be plugged into an

appropriate outlet, properly installed

and grounded in accordance with all

codes and ordinances. The plug and

outlet should look like those in the

preceding illustration.

(See 3‑Prong Plug and Outlet.)

Double Insulated Tools:

Tools with Two Prong Plugs

Outlets for 2‑Prong Plug

1. Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satises

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian

Standard Association, and the National

Electrical Code.

2. Double insulated tools may be used in

either of the 120 volt outlets shown in the

preceding illustration.

(See Outlets for 2‑Prong Plug.)

Extension Cords

1. Grounded tools require a three wire

extension cord. Double Insulated

tools can use either a two or three wire

extension cord.

2. As the distance from the supply outlet

increases, you must use a heavier gauge

extension cord. Using extension cords

with inadequately sized wire causes a

serious drop in voltage, resulting in loss

of power and possible tool damage.

(See Table A on page <?>.)

3. If you are using an extension cord

outdoors, make sure it is marked with the

sufx “W-A” (“W” in Canada) to indicate it

is acceptable for outdoor use.

4. Protect the extension cords from sharp

objects, excessive heat, and damp or

wet areas

TABLE A: RECOMMENDED MINIMUM

WIRE GAUGE FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25´ 50´ 75´ 100´ 150´

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop to ve volts at

150% of the rated amperes.

Page 8 For technical questions, please call 1‑800‑444‑3353. SKU 95630

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute

(RPM)

WARNING marking

concerning Risk of Eye Injury.

Wear ANSI-approved safety

goggles with side shields.

Read the manual before set-up

and/or use.

WARNING marking concerning

Risk of Hearing Loss.

Wear hearing protection.

WARNING marking concerning

Risk of Fire.

Do not cover ventilation ducts.

Keep ammable objects away.

WARNING marking concerning

Risk of Electric Shock.

Properly connect power cord to

appropriate outlet.

Description

Compressor Specications

Type Single cylinder, oiless piston

Power 1/5 HP

Voltage 120, 60HZ, 1.18 AMP

Thermo-Overload

shutoff protection Auto shutoff

Air output 0 - 58 PSI

Air outlet size 1/8 - 27 NPT male threads

Motor RPM 1750

Pressure Gauge 0-100 PSI

Cord length 6’-2 1/2”L

Air Brush Specications

Working Air

Pressure 0.5 CFM @ 20 PSI

Air Hose length Approx. 5FT

Housing Anodized Aluminum

Accessories

22cc Glass jar assembly

5cc Metal cup

Metal Hanger

INITIAL ASSEMBLY

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set up

or use of this product.

Note: For additional information regarding

parts listed in following pages, refer to

Assembly Diagrams near end of manual.

Unpacking

When unpacking, make sure that the

item is intact and undamaged. If any parts

are missing or broken, please call Harbor

Freight Tools at 1-800-444-3353 as soon

as possible.

Functional Description

Page 9For technical questions, please call 1‑800‑444‑3353.SKU 95630

Assembly

Read the ENTIRE

IMPORTANT SAFETY

INFORMATION section at the

beginning of this manual

including all text under

subheadings therein before set

up or use of this product.

Inspect tool before use, looking

for damaged, loose, and missing

parts. If any problems are found,

do not use tool until repaired.

1. Connect one end of the air hose to the

Air Outlet (38).

2. Connect other end of air hose to the Air

Brush (27).

3. Inspect the air connections for leaks.

Repair any leaks found.

Operating Instructions

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set up

or use of this product.

Inspect tool before use, looking

for damaged, loose, and missing

parts. If any problems are found,

do not use tool until repaired.

Work Piece and Work Area Set Up

1. Designate a work area that is clean and

well-lit. The work area must not allow

access by children or pets to prevent

distraction and injury.

2. Route the air hose along a safe route to

reach the work area without creating a

tripping hazard or exposing the air hose

to possible damage. The air hose must

be long enough to reach the work area

with enough extra length to allow free

movement while working.

3. Secure loose workpieces using a vise

or clamps (not included) to prevent

movement while working.

4. There must not be hazardous objects

(utility lines or foreign objects) nearby

that present a hazard while working.

General Operating Instructions

1. Choose a 120V power supply and plug in

Air Compressor.

2. Set the Pressure Gauge to desired air

pressure (maximum 58 PSI).

3. Fill the 22cc Glass Jar (31A) after

thinning your paint properly.

NOTE: Use the proper solvent for thinning.

Use lacquer thinner for all lacquers, paint

thinner for oil based paints, and water for

all latex based paints.

4. Hold the Air Brush Housing (8A) lightly

in your hand and push the tappered

tting on the lid of the 22cc Glass Jar

Assembly (31A) into the base of the Air

Brush Housing (8A). It is held in place

with friction and not threading.

5. Turn on the Power Switch (34) and

the Air Compressor will start and

work continuously until it reaches its

maximum preset pressure which will

be approximately 55 PSI at which time

it will automatically shut down. It will

re-start when the pressure drops to

approximately 42 PSI.

6. By pressing the Finger Lever (10A)

air will emerge from the Nozzle (3A).

Draw back slowly/gently on the Finger

Initial Tool Setup/Assembly

Operating Instructions

Page 10 For technical questions, please call 1‑800‑444‑3353. SKU 95630

Lever (10A)) and the uid will atomize.

Continue to move the Finger Lever (10A)

to achieve the air volume you need for

your spray technique.

7. Continue to adjust the spray volume by

using the Finger Lever (10A), moving it

front to back. When you have the correct

spray volume, you may x the position

using the Adjustment Screw (9A).

8. The size of the spray pattern will be in

accordance with the distance between

the work surface and the Nozzle (3A)

of the Air Brush. For extra-ne spray,

remove the Protective Cap (1A) and hold

the Air Brush nearer the work surface.

9. When you are nished painting, gently

release pressure on Finger Lever (10A).

NOTE: If while using this Air Brush and

uid blocks the Nozzle (3A) from

working, move Needle Chucking

Guide (13A) back and forth. If this

does not clear the Nozzle (3A), try

loosening the Needle Adjustment

Screw (9A). This will allow a longer

movement for the Needle (18A) and

allow the blocked uid to escape

clearing the Nozzle (3A).

10. After ushing the Air Brush unit

completely with the proper solvent:

Lacquer thinner if you used a lacquer

paint, water if you used a latex based

paint and paint thinner for all oil based

enamels, spray remaining solvent

through the Nozzle (3A) until clear

solvent sprays from end of Airbrush tip.

NOTE: ALL paints used with this Air Brush

are fast drying by design and can

seriously damage your tool if they are

NOT ushed immediately.

11. Bleed excess air from hose and drain

water out of the Water Drain Valve (23)

on the Air Compressor only after turning

OFF Power Switch (34) and unplugging

the Compressor from the 120 V power

supply, or from your extension cord.

NOTE: The 5cc Metal Cup (28A) has two

uses. It is used for excess thinned paint,

and also for solvent when it is time to

clean the Air Brush.

NOTE: The Metal Hook (30A) can be

attached to a solid surface and used to

hang Air Brush when it is not being used.

USER‑INSTRUCTIONS

Procedures not specically

explained in this manual must

be performed only by a qualied

technician.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL OPERATION,

make sure Power Switch of tool

is in its “Off” position and that

the tool is unplugged from its

electrical outlet before any

maintenance or repairs are done.

Note: These procedures are in addition to

the regular checks and maintenance

explained as part of the regular operation

of the air-operated tool.

1. BEFORE EACH USE, inspect the

general condition of the tool. Check for

loose screws, misalignment or binding

of moving parts, cracked or broken

parts, damaged electrcial wiring, and

any other condition that may affect

its safe operation. If abnormal noise

or vibration occurs, have the problem

corrected before further use. Do not

use damaged equipment.

2. AFTER EACH USE, wipe off with a

clean, moist cloth. Also completely ush,

User‑Maintenance Instructions

Tabla de contenidos

Otros manuales de Compresor de aire de Central Pneumatic

Central Pneumatic

Central Pneumatic 95498 Manual de instalación

Central Pneumatic

Central Pneumatic 42321 Manual de usuario

Central Pneumatic

Central Pneumatic 45214 Manual de usuario

Central Pneumatic

Central Pneumatic 93351 Manual de usuario

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 47407 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 99659 Manual de instalación

Central Pneumatic

Central Pneumatic Central Pneumatic 30 Gallon, 180 PSI Gas Powered Two-Stage Air... Manual de usuario

Central Pneumatic

Central Pneumatic CentralPneumatic 68064 Manual de instalación

Central Pneumatic

Central Pneumatic 62913 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 90234 Manual de usuario

Central Pneumatic

Central Pneumatic 93657 Manual de usuario

Central Pneumatic

Central Pneumatic 68067 Instrucciones de montaje

Central Pneumatic

Central Pneumatic CentralPneumatic 17 GAL Instrucciones de montaje

Central Pneumatic

Central Pneumatic PROFESSIONAL 99901 Manual de usuario

Central Pneumatic

Central Pneumatic 67696 Manual de instalación

Central Pneumatic

Central Pneumatic 90749 Manual de usuario

Central Pneumatic

Central Pneumatic 56101 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 62380 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 40131 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 62779 Manual de usuario

Central Pneumatic

Central Pneumatic 60637 Guía del usuario

Central Pneumatic

Central Pneumatic 95386 Manual de instalación

Central Pneumatic

Central Pneumatic 98635 Manual de instalación

Central Pneumatic

Central Pneumatic CentralPneumatic 69269 Instrucciones de montaje

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario