Cembre B-TC650NA Manual de usuario

OPERATION AND MAINTENANCE MANUAL

17 M 208 U

BATTERY OPERATED HYDRAULIC

CUTTING TOOL

ENGLISH

B-TC650A B-TC650NA

Low battery

FIG. 2

FIG. 3a

FIG. 4

16 2

Cu Al Steel

FIG. 3

Makita

battery FIG. 1b

FIG. 1a

Metabo

battery

LED WORKLIGHT

UPPER BLADE

LOWER BLADE

LATCH

OPERATING BUTTON

PRESSURE RELEASE BUTTON

BATTERY RELEASE

BATTERY

RING FOR SHOULDER STRAP

BATTERY ADAPTER

FIG. 5

B-TC650A B-TC650NA

– Before using the tool, carefully read the instructions in this manual.

– Keep hands clear of cutting blades.

– Always wear safety glasses and gloves when operating this tool.

WARNING SYMBOLS

– User information applies in member states of the European Union

(Directives 2011/65/EU and 2012/19/EU), see page 9.

Battery

Tool

(

– Do not cut Steel.

– Never throw batteries into re or water.

– Always recycle the batteries.

– Do not discard batteries into domestic refuse or waste disposal.

1. GENERAL CHARACTERISTICS

(1) Directive 2006/42/EC, annexe 1, point 1.7.4.2 letter u

LpA

= weighted continuous acoustic pressure level equivalent.

LpCPeak

= maximum value of the weighted acoustic displacement pressure at the work place.

LWA

= acoustic power level emitted by the machine.

(2) Directive 2006/42/EC, annexe 1, point 2.2.1.1

Weighted root mean square in frequency of the acceleration the upper limbs are exposed to for each biodynamic

reference axis. Tests carried out in compliance with the indications contained in EN ISO 5349-1/2 Standard and under

operating conditions much more severe than those normally found.

B-TC650A B-TC650NA

Application range suitable for cutting Copper, Aluminium

or telephone cables

Max. cutting diameter mm (inches) 65 (2-9/16")

Operating pressure

bar (psi) 700 (10,000)

Dimensions (Fig. 9 and g.

10 page 10) mm (inches) 429 x 415 x 83

(16.9 x 16.3 x 3.3)

429 x 435 x 83

(16.9 x 17.1 x 3.3)

Weight with battery kg (lbs) 6,4 (14.1) 6,5 (14.4)

Motor V DC 18

Operating temperature °C (°F) -15 to +50 (+5 to +122)

Recommended oil ENI ARNICA ISO 32 or equivalents

Operating speed twin speed operation and automatic switching from

a rapid advancing speed of the ram to a slower, more

powerful speed

Safety maximum pressure valve

Rechargeable battery type CB1840L MAKITA BL1850B

Type V / Ah (Wh) 18 / 4.0 / (72) 18 / 5.0 (90)

Weight kg (lbs) 0,66 (1.45) 0,6 (1.3)

Acoustic noise

(1)

dB (A)

pCPeak

dB (C) 94.5

dB (A) 79

Vibration

(2)

m/s

0.575 max.

Battery charger

Input

type

V / Hz

ASC30-36 MAKITA DC18RC

115 / 60 120 / 50 - 60

This tool has been specically designed for cutting Copper or Aluminium cables.

DO NOT ATTEMPT TO CUT STEEL ROPES OR STEEL REINFORCED CONDUCTORS.

Do not use the tool for purposes other than those intended by Cembre.

The operator should concentrate on the work being performed and be careful to maintain a bal-

anced working position.

Work in a clean, uncluttered area. Keep persons away from immediate work area.

Inspect the blades before each use. Do not use damaged blades.

Damaged blades can break and cause injury or damage to the tool.

Before each use, verify the integrity of the tool; replace any worn, possibly damaged or missing

parts with original Cembre spares.

Wear eye protection. Metal chips can y from blades when cutting.

Do not cut live cables or conductors.

The tool is unsuitable for continuous use and should be allowed to cool down following uninter

rupted, successive cutting operations; for instance, having exhausted a fully charged battery in

one session, delay battery replacement for a few minutes.

Protect thetoolfromrainandmoisture.Waterwilldamage thetool andbattery.Electro-hydraulic

tools should not be operated in pouring rain.

The part reference includes the following:

Hydraulic cutting tool (B-TC650NA is tted with adapter to use Makita battery).

Li-Ion rechargeable battery (2 pcs) (model depends on the tool version).

Battery charger

Shoulder strap.

Plastic carrying case.

USB cable (Ref. to § 5).

2. INSTRUCTIONS FOR USE

The tool can be easily carried using either the handle or the shoulder strap attached to ring (9)

(Ref. to Fig. 5).

Before starting any work, check the battery charge (Ref. to § 2.7) and recharge if necessary.

Refer to the manufacturer's instructions for the correct use of battery and battery charger.

To replace the battery, remove it by pressing the release button (7) (Ref. to Fig. 1a and 1b),

B-TC650A: in the g. 1a press the release button (7) and slide the battery out unlocking it.

B-TC650NA: in the g. 1b press the release buttons (7) and slide the battery out unlocking it.

Insert a charged battery by sliding it into the guides until it locks.

2.1) Head rotation

For ease of operation, the tool head can rotate, allowing the operator to work in the most comfort-

able position (Ref. to Fig. 3).

Do not attempt to rotate the head when the hydraulic circuit is pressurised.

WARNING

2.2) Setting

Insert the conductor between the blades, up to the desired cutting point (Ref. to Fig. 3).

For a running conductor, release the latch (4) and open the tool head (Ref. to Fig. 3a).

Fully retract the lower blade (3) before attempting to open the tool head (Ref. to § 2.6).

With the conductor on the lower blade (3), close the tool head and fully secure the latch (4).

Before commencing the cutting operation ensure that the latch (4) is fully secured: partial

closure may damage the tool head.

2.3) Blade advancement

Press the operating button (5) (Ref. to Fig. 3) to activate the motor-pump, the ram will gradually

move forward until the lower blade (3) touches the conductor.

To halt the advancement, release the button (5) and the motor will cut out.

2.4) Cutting

Firmly hold thetoolandoperatethebutton(5)togradually move thelowerblade (4)to cuthrough

the conductor.

When the cut is performed, release the button (5), otherwise after the maximum pressure relief

valve has activated the motor will stop automatically.

2.5) LED Worklights

Whilst the tool is in operation, the work area is illuminated by two high luminosity LED Worklights

that switch o automatically at the end of the cycle.

2.6) Blade retraction

By operating the pressure release button (6), the ram will retract and open the lower blade.

2.7) Battery status

The battery is equipped with LED indicators that indicate the

remaining battery life at any time by pressing the adjacent but-

ton (P):

4 LEDs illuminated: fully charged

2 LEDs illuminated: 50 % capacity

1 LED flashing: minimum charge, replace the battery

Worklights (1) illuminated combined with an alarm au-

dible when the operating button (5) is pressed (Ref. to Fig.

5), indicate that the battery voltage has dropped below a

minimum safety threshold; under these conditions the tool will not start, and it is necessary to re-

charge or replace the battery.

The approximate time to fully recharge a battery is about 80 minutes.

After each working cycle, and after the extraction of the battery from the tool, an integrated

battery cut-o device will operate after 70 s approx. Then the LED nearest to button (P) will

ash 5 times each 14 s approx. The battery will be reactivated when it is reintroduced into

the tool and the operating button is pressed.

2.8) Using the battery charger

Carefully follow the instructions in the battery charger user manual.

3. MAINTENANCE

The tool is robust, completely sealed, and requires very little daily maintenance. Compliance with

the following points, should help to maintain its optimum performance:

3.1) Thorough cleaning

Dust, sand and dirt are a danger for any hydraulic device. Every day, after use, the tool must be

wiped with a clean cloth taking care to remove any residue, especially close to pivots and move-

able parts.

Do not use hydrocarbons to clean the rubber parts.

Regularly lubricate the moving parts and pivot pins of the head with a few drops of oil.

3.2) Storage case

When not in use, the tool should be stored and transported in the plastic case, to prevent damage.

The case, type VAL-P40, is suitable for storing the tool and accessories.

VAL-P40: Size 520x432x126 mm (20.5x17.0x5.0 inches). Weight 2,6 kg (5.7 lbs).

3.3) Routine maintenance

When the tool reaches the predetermined number of hours worked, it will signal that routine

maintenance is recommended.

The tool will continue to work however 15 sec. after use an alarm comprising 3 beeps com-

bined with illumination of the worklights will signal that its return to Cembre for service is

recommended (see § 6).

4. BLADE REPLACEMENT (Ref. to Fig. 4)

When changing blades, the battery must rst be removed from the tool.

After extended use, the blades may lose their cutting edge. Replace the blades as follows:

Lower blade

– Release latch (4) and open the tool head.

– Operate tool to advance the lower blade (3) until holding screw (13) is visible on the ram (12),

than remove the battery from the tool.

– Using a at blade screwdriver remove the holding screw (13) and release the lower blade (3).

– Insert the new blade and t the holding screw.

Before closing the tool head, release the oil pressure and retract the lower blade, otherwise

the tool head assembly may hit and damage the lower blade.

Upper blade

– Release latch (4) and open the tool head.

– Remove the circlip (18) and extract the head pivot (14), enough to release the tool head assembly.

– Remove circlip (22) and pivot pin (21), to release the latch (4).

Remove latch spring (17) from the upper blade (16).

– Unscrew the 4 screws (20) and remove the left hand guide (15) and the right hand guide (16) to

release the blade (2).

– Fit the left and right hand guides to the new blade, place the spring (17) into its seat and re-t

the latch (4).

– Fit the blade assembly to the head (19), fully insert the pivot (14) and secure with the circlip (18).

5. CONNECTION TO COMPUTER

Thememorycardintegratedinthetoolrecordsoperatingdata fortransferviatheUSBcablesupplied.

To view and manage this data, go to www.cembre.com and register in the dedicated area, then

download the free Cembre software CEM_SWBT01.

Keeping the Firmware of the tool updated, via free of charge download from here, will optimise

the tool’s performance.

B-TC650NA: To access the mini-USB

port (Ref. to g. 6) and connect the USB

cable to the computer it is necessary to

remove CBA-MTMK battery adapter.

Remove the screw (Ref. to g. 7 and 7a)

and slide the adapter out.

CBA-MTMK

Screw

FIG. 7

mini-USB

FIG. 7a

FIG. 6

B-TC650NA

USER INFORMATION in accordance with “Directives 2011/65/EU and 2012/19/EU.“

The ‘Not in the bin’ symbol above when shown on equipment or packaging means that

the equipment must, at the end of its life, be disposed of separately from other waste.

The separate waste collection of such equipment is organised and managed by the manufacturer.

Users wishing to dispose of such equipment must contact the manufacturer and follow the prescribed

guidelines for its separate collection. Appropriate waste separation, collection, environmentally compat-

ible treatment and disposal is intended to reduce harmful environmental eects and promote the reuse

and recycling of materials contained in the equipment. Unlawful disposal of such equipment will be sub-

ject to the application of administrative sanctions provided by current legislation.

–

Following information applies in member states of the European Union:

429 (16.9)

435 (17.1)

83 (3.3)

429 (16.9)

415 (16.3)

83 (3.3)

FIG. 9 mm (inch) B-TC650A

FIG. 10 mm (inch) B-TC650NA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortador de Cembre

Cembre

Cembre B500-TFC Manual de usuario

Cembre

Cembre TC04N Manual de usuario

Cembre

Cembre HT-TC0851 Manual de usuario

Cembre

Cembre HT-TC051Y Manual de usuario

Cembre

Cembre B-TC04 Manual de usuario

Cembre

Cembre B-TC095 Manual de usuario

Cembre

Cembre HT-TC041N Manual de usuario

Cembre

Cembre B-TC950A Manual de usuario

Cembre

Cembre B-TC450 Manual de usuario

Cembre

Cembre B35M-TFC Manual de usuario

Cembre

Cembre HT-TC026 Manual de usuario

Cembre

Cembre B-TC04 Manual de usuario

Cembre

Cembre B-TC065-SC Manual de usuario

Cembre

Cembre B-TC250 Manual de usuario

Cembre

Cembre HT-TC065 Manual de usuario

Cembre

Cembre B35M-TC025 Manual de usuario

Cembre

Cembre HT-TFC Manual de usuario

Cembre

Cembre TC050Y-KV Manual de usuario

Cembre

Cembre HT-TC051Y Manual de usuario

Cembre

Cembre HT-TC051 Manual de usuario

Cembre

Cembre TC050 Manual de usuario

Cembre

Cembre TC085 Manual de usuario

Cembre

Cembre HT-TC026 Manual de usuario

Cembre

Cembre B35 Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario