CDVI GALEO/W Manual de usuario

Edition 10/2006 G0301FR0266V01

MOUNTING KIT

Qty Description Photo Utilisation

M4x10 tamper screw GALEO Mounting screw

T20 spanner For the M4x10 screw

M4x30 mounting screws 2 * keypad back plate

2 * Remote Controller

2 Caps GALEO cap

S5 plastic anchor 2 * keypad back plate

2 * Remote Controller

05D 680K varistor For the lock

2 Wiring sealed caps Cable to the controller

Dimensions: 110 x 75 x 15 mm

CABLE

Description

Red 12V DC (+)

Black 0V

Brown Buzzer command input

Green Data 0

White Data 1

Blue Clock

Gray 0V common

GALEO/W

ILLUMINATED ONLINE KEYPAD

26 BIT OUTPUT FORMAT, CLOCK &

DATA and CDVI OUTPUT FORMAT

INSTALLATION MANUAL

IP 64 DM

Edition 10/2006 G0301FR0266V01

I. GENERAL INFORMATION

A. Description

Input voltage 12V DC

12-digit illuminated keypad keys

EEPROM memory storage

User code in 4, 5 or 6 digits

Buzzer

ST1 jumper for programming

B. Default values

Illumination duration: 10 seconds

User code lenght: 5 digits

26 bit wiegand output

Buzzer disabled

C. Audible Signal

1 short beep keypad powered and key presses

1 long beep data computing in programming

2 short beeps Entry or Exit from programming

4 short beeps data computing error

D. Code Length

The user code must be in 4, 5 or 6 digits.

All the keypad keys can be used to program a user code except the B key.

Enter the user code and then B to validate the code.

E. Consumption

80mA in 12 VDC (permanent illuminated keys)

II. PROGRAMMING

A. Entry in programming

1. Turn off the power. Put the switch to ON. Put back the power.

2. Two beeps are emitted to confirm entry in programming.

The command control of the buzzer is not possible in programming mode.

B. Illumination duration

1. Enter in programming.

2. Enter A0 to program the illumination duration. One beep is emitted. Enter the time in

seconds – 10 for 10 seconds to 99 for 99 seconds or enter 00 for a permanent illumination.

One beep is emitted to confirm the illumination duration.

Edition 10/2006 G0301FR0266V01

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

C. Output format

1. Enter in programming.

2. Press A1 to enter in the output format menu. One beep is emitted.

Press 1 to select 26-bit wiegand output format

Press 2 to select CDVI output format

Press 3 to select ISO Track 2 output format

One beep is emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

C. Code length

1. Enter in programming mode.

2. Press A2 to enter in the code length setting menu. One beep is emitted. Press 4 for a 4-digit

user code, press 5 for a 5-digit user code or press 6 for a 6-digit user code. One beep is

emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

4 beeps indicate a data computing error.

D. Audible signal

The audible signal is always enabled in programming mode.

In factory default, the buzzer is disabled when pressing a key. To enable the buzzer:

1. Enter in programming mode.

2. Press A3. One beep is emitted. Press 0 to disable the audible signal. Press 1 to enable the

audible signal. One beep is emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

E. External control of the buzzer

The buzzer can be activated from an external input. The control is done with a logic signal on the

input.

Buzzer enabledBuzzer disabled Buzzer disabled

Edition 10/2006 G0301FR0266V01

F. 26-bit wiegand format

Interfaçage

The output format is 26-bit Wiegand (Signals: DATA1, DATA0 and CLOCK)

Output signal in open collectors (pull up of 2.2K in +5V)

26-bit hexadecimal output format

The frame is made of 26-bit and built as follow:

First parity: 1-bit – even parity for the first 12-bit

User Code: 3 half of a byte represent the code entered

Each byte is transferred from bit 7 to bit 0.

Second parity: 1-bit – odd parity for the last 12-bit

Bit 1 Bit 2 … bit 25 bit 26

Even parity on bit 2…bit13 Data (24 bits) Odd parity on bit 14…bit 25

Example a 4-digit code: 1350 then B

1 0000 0000 0001 0011 0101 0000 1

Parity 1 0 0 1

3 5 0 Parity 2

The code is transmitted in hexadecimal: 001350

Example a 5-digit code: 71350 then B

0 0000 0111 0001 0011 0101 0000 1

Parity 1 0 7 1 3 5 0 Parity 2

The code is transmitted in hexadecimal: 071350

Example a 6-digit code: 671350 then B

0 0110 0111 0001 0011 0101 0000 1

Parity 1 6 7 1 3 5 0 Parity 2

The code is transmitted in hexadecimal: 671350

Parity 1: 0 if the number of 1 in bit 2 to bit 13 is even

1 if the number of 1 in bit 2 to bit 13 is odd

Chronograms

\CLOCK

\DATA1

\DATA0

0 logic 1 logic

50s 50s2ms 2ms

Edition 10/2006 G0301FR0266V01

Parity 2: 0 if the number of 1 in bit 14 to bit 25 is odd

1 if the number of 1 in bit 14 to bit 25 is even

G. CDVI Format

This format is owned by CDVI. This format is compatible with other CDVI products ( PROMI, UCA3 ).

H. ISO 7811 Track 2 Format

SS Characters ES

LRC

SS = start sentinel Hex B

ES = end sentinel Hex F

LRC = Ou Exclusif de tous les caractères de la trame (including SS and ES)

The code length is set at 8 digits:

In 4 digits – 00001234

In 5-digits – 00012345

In 6-digits - 00123456

Each digit is made of 5 bits (4 bits data + 1 bit parity)

Characters

B4 B3 B2 B1 Parity

0 0 0 0 0 1

1 0 0 0 1 0

2 0 0 1 0 0

3 0 0 1 1 1

4 0 1 0 0 0

5 0 1 0 1 1

6 0 1 1 0 1

7 0 1 1 1 0

8 1 0 0 0 0

9 1 0 0 1 1

A 1 0 1 0 1

B = SS 1 0 1 1 0

C 1 1 0 0 1

D = FD 1 1 0 1 0

E 1 1 1 0 0

F = ES 1 1 1 1 1

/Présence

/Data

/Clock

Edition 10/2006 G0301FR0266V01

III. MOUNTING INSTRUCTIONS

Drill (bit Ø5mm) 2 mounting holes

(minimum depth 35mm) and the cable

hole.

Insert the S5 2 plastic anchors in the

holes.

Mount the back plate with the M4x30

screws.

Insert the cable of the GALEO®inside

to cable hole.

Place the GALEO®on the back plate

and slide it from up to down. Make sure

that the mounting bracket is properly

set with the GALEO.

Use the M4x10 screw to close the

keypad (T20 spanner). Place the screw

cap.

To mount the remote controller on the wall use the plastic bracket.

GALEO

Otros manuales para GALEO/W

Tabla de contenidos

Otros manuales de Teclado de CDVI

CDVI

CDVI Galeo Manual de usuario

CDVI

CDVI KCINBT Manual de usuario

CDVI

CDVI SUBLIM Manual de usuario

CDVI

CDVI GALEO/W Manual de usuario

CDVI

CDVI KCIN Manual de usuario

CDVI

CDVI Galeo Manual de usuario

CDVI

CDVI GALEO 4.0 - Bluetooth Manual de usuario

CDVI

CDVI GALEO 4.0 - Bluetooth Manual de usuario

CDVI

CDVI SOLAR2R Manual de usuario

CDVI

CDVI KCIENSBP Manual de usuario

CDVI

CDVI Digicode Series Manual de usuario

CDVI

CDVI GALEO 4.0 - Bluetooth Manual de usuario

CDVI

CDVI CAA Manual de usuario

CDVI

CDVI Galeo Manual de usuario

CDVI

CDVI DC100E Manual de usuario

CDVI

CDVI GALEO/W Manual de usuario

CDVI

CDVI CBB Manual de usuario

CDVI

CDVI Digicode DGA Manual de usuario

CDVI

CDVI GALEOR Manual de usuario

CDVI

CDVI Galeo Manual de usuario

CDVI

CDVI Digicode PROFIL100EC Manual de usuario

CDVI

CDVI PROMI E Guía de inicio rápido

CDVI

CDVI Krypto K3 Manual de instrucciones

CDVI

CDVI Digicode Series Manual de usuario

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento