Cateye CC-PA110W Manual de usuario

CATEYE

PADRONE

CYCLOCOMPUTER

CC-PA110W

Setting up the

computer

Mounting the

computer

Starting

measurement

Changing settings

Warning / Caution

Product Warranty, etc.

• This instruction manual is subject to change

without notice. See our website for the latest

instruction manual (PDF).

• Please visit our website, where a detailed

Quick Start manual containing videos can be

downloaded.

http://www.cateye.com/products/detail/CC-PA110W/manual/

Appendix

SET 4

(1/3)

(2/3)

Mounting the computer

1 Mount the bracket

• When mounting on stem

• When mounting on handlebar

When mounting the bracket on a handle-

bar, adjust the angle of the bracket so that

the back of the computer faces the speed

sensor when the computer is attached.

Bracket band

Bracket Dial

Bracket rubber pad Speed sensor

Sensor rubber pad

Magnet

Nylon tie

(x2)

StemBracket band

Bracket

Bracket rubber pad

HandlebarBracket band

Bracket

Bracket rubber pad

Cutting band after mounting

CAUTION:

Cut the bracket band so

that cut end will not cause

injury.

Dial

Cut

Correct Wrong

Appendix

SET 4

(1/3)

(3/3)

(2/3)

Max.

70 cm

Mounting the computer

2 Mount the speed sensor

3 Mount the magnet

Mount the speed sensor in a posi-

tion where the distance from the

computer to the speed sensor is

within the signal range.

• Mounting on left front fork

• Mounting on right front fork

SENSOR ZONE

Cut

Pull tight

Nylon tie

Speed sensor

Sensor rubber pad

To sensor zoneSpoke

Magnet

Appendix

SET 4

(3/3)

(2/3)

SENSOR ZONE

5 mm

Mounting the computer

5 Attach/detach computer

6 Test operation

After attaching the computer, rotate the front wheel gently to check that current

speed is displayed on the computer.

If the speed is not displayed, refer to the attachment conditions in steps 1, 2, and 4

again.

4 Adjust the speed sensor and the magnet

* The magnet may be mounted at any position on spoke as long as attachment

conditions are satisﬁed.

The magnet passes through

the speed sensor zone.

The clearance between the

speed sensor and the magnet

is within 5 mm (3/16”).

Magnet

Sensor zone

Speed sensor

Speed sensorMagnet

ClickClick Hold computer.

Push out so that front lifts up.

Appendix

SET 4

(1/2)

(2/2)

When using the

computer for the

ﬁrst time, conﬁgure

the initial settings.

MODE

Battery case

cover

Dot section

Short press

Long press

(2 sec.)

1 Clear all data.

Press the AC button on the back of the computer.

* All data is deleted and the computer is reset

to its factory default settings.

2 Select the measurement unit.

Select “km/h” or “mph”.

3 Set tire circumference.

Enter the tire circumference of the front wheel

in mm.

* Refer to “Tire circumference”(page 6).

4 Set the clock.

Each time MODE is pressed and held, settings

switch from time display mode, to hours, to

minutes.

* When 12h mode is selected, make sure to

check whether A(a.m.) or P(p.m.) is dis-

played before entering the value.

5 Press MENU to complete setup.

Setup is completed and the computer switches to the mea-

surement screen. For instructions on how to start mea-

surement, refer to “Starting measurement”(page 7).

MODE

Setting up the computer

km/h ↔mph

Conﬁrm

Increase

numbers

Move to next digit

(Press and hold)

Conﬁrm

Setup complete

MODE

Switch between

24h and 12h or

increase numbers

Switch setting item

(Press and hold)

Time display mode

MinutesHours

Appendix

SET 4

(1/2)

(2/2)

Tire circumference

Tire circumference can be determined by either of the following two methods:

• Measure the actual tire circumference (L)

After ensuring that the tire pressure is appropriate, sit on your

bike, roll it forward so that the tire makes one full revolution (use

the valve or other marking as a reference), and measure the dis-

tance traveled on the road.

• Tire size chart

* The tire size or ETRTO code is indicated on the side of the tire.

ETRTO Tire size

L (mm)

47-203 12x1.75 935

54-203 12x1.95 940

40-254 14x1.50 1020

47-254 14x1.75 1055

40-305 16x1.50 1185

47-305 16x1.75 1195

54-305 16x2.00 1245

28-349 16x1-1/8 1290

37-349 16x1-3/8 1300

32-369 17x1-1/4 (369) 1340

40-355 18x1.50 1340

47-355 18x1.75 1350

32-406 20x1.25 1450

35-406 20x1.35 1460

40-406 20x1.50 1490

47-406 20x1.75 1515

50-406 20x1.95 1565

28-451 20x1-1/8 1545

37-451 20x1-3/8 1615

37-501 22x1-3/8 1770

40-501 22x1-1/2 1785

47-507 24x1.75 1890

50-507 24x2.00 1925

54-507 24x2.125 1965

25-520 24x1(520) 1753

24x3/4 Tubular 1785

28-540 24x1-1/8 1795

32-540 24x1-1/4 1905

25-559 26x1(559) 1913

32-559 26x1.25 1950

37-559 26x1.40 2005

40-559 26x1.50 2010

47-559 26x1.75 2023

50-559 26x1.95 2050

54-559 26x2.10 2068

57-559 26x2.125 2070

58-559 26x2.35 2083

ETRTO Tire size

L (mm)

75-559 26x3.00 2170

28-590 26x1-1/8 1970

37-590 26x1-3/8 2068

37-584 26x1-1/2 2100

650C Tubular 26x7/8

1920

20-571 650x20C 1938

23-571 650x23C 1944

25-571 650x25C 26x1(571) 1952

40-590 650x38A 2125

40-584 650x38B 2105

25-630 27x1(630) 2145

28-630 27x1-1/8 2155

32-630 27x1-1/4 2161

37-630 27x1-3/8 2169

40-584 27.5x1.50 2079

50-584 27.5x1.95 2090

54-584 27.5x2.1 2148

57-584 27.5x2.25 2182

18-622 700x18C 2070

19-622 700x19C 2080

20-622 700x20C 2086

23-622 700x23C 2096

25-622 700x25C 2105

28-622 700x28C 2136

30-622 700x30C 2146

32-622 700x32C 2155

700C Tubular 2130

35-622 700x35C 2168

38-622 700x38C 2180

40-622 700x40C 2200

42-622 700x42C 2224

44-622 700x44C 2235

45-622 700x45C 2242

47-622 700x47C 2268

54-622 29x2.1 2288

56-622 29x2.2 2298

60-622 29x2.3 2326

Setting up the computer

L mm

Appendix

SET 4

(2/3)

(1/3)

MODE

* Av displays .E instead of the measurement value when Tm exceeds approximately

100 hours or Dst exceeds 9999.99 km. Reset the computer.

Switching current function

Pressing MODE switches the current function displayed at the bottom of the screen.

Starting measurement [Measurement screen]

On the measurement screen, press MENU to go to the menu

screen. Various settings can be changed on the menu screen.

MODE

Night Mode icon

Turns on when Night Mode

is ON. For details, refer to

page 10.

Current speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.0 mph]

Measurement unit

Current function

MODE operation when mounted on bracket

When the computer is mounted on the brack-

et, pressing the dot section on the computer

depresses the MODE button.

Moving Time

0:00’00” – 99:59’59”

Trip Distance

0.00 – 9999.99 km [miles]

Average Speed (*)

0.0 – 99.9 km/h

[0.0 – 62.0 mph]

Stopwatch

Turning ON the

stopwatch setting

on the menu screen

adds a stopwatch

to the current func-

tion display. 0:00’00” – 99:59’59”

Maximum Speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.0 mph]

Total distance

0.0 – 99999.9 km [miles]

Clock

0:00 – 23:59 or

1:00 – 12:59

Appendix

SET 4

(2/3)

(1/3)

(2/3)

(3/3)

MODE

Starting/stopping measurement

Measurement starts automatically when the

bicycle moves.

During measurement the measurement unit

(km/h or mph) ﬂashes.

Resetting data

Pressing MODE for 2 seconds when on the measurement screen

resets all measurement data to 0 (excluding Odo).

Backlight (Night Mode)

The backlight will come on during the time speciﬁed in the Night Mode settings on the

menu screen.

The backlight can be set to come on part time (for 5 seconds) or full time (constantly).

* When the remaining battery power is low (when turns on), the backlight will not

turn on.

Dot

(MODE)

Dot

(MODE)

•

When Full time is selected:

The backlight will come ON while the bicy-

cle is in motion and will turn OFF 30 sec-

onds after the bicycle has stopped.

•

When Part time is selected:

The backlight will come on when MODE is

pressed. Pressing MODE while the back-

light is ON will activate the button’s func-

tion and extend the lighting time.

Starting measurement [Measurement screen]

(2 seconds)

*1: Pressing MODE will turn the backlight

ON, but the button function is disabled.

*2: Pressing the button again while the

backlight is ON will activate the button’s

function.

Backlight off

Backlight on

(*1)

Button function

(*2)

Bicycle begins moving 30 seconds

after stopping

Backlight off Backlight off

Backlight

constantly ON

Measurement stops

Measurement starts

Appendix

SET 4

(3/3)

(2/3)

Starting measurement [Measurement screen]

Power-saving function

If the computer does not receive

any signal for 10 minutes, the

power-saving screen is activated

and only the clock is displayed.

If MODE is pressed or a sensor

signal is received while the pow-

er-saving screen is activated, the

computer returns to the measure-

ment screen.

* When the computer is left on

the power-saving screen for 1

hour, the display only shows the

measurement unit. When the

computer is in this state, you

can return to the measurement

screen by pressing MODE.

Using the stopwatch ( )

You can display a stopwatch to count time regardless of whether measurement is started

or stopped.

To use the stopwatch, set the stopwatch setting on the menu screen to ON.

For instructions on how to set the stopwatch, refer to “Stopwatch” (page 13).

Stopwatch operation

Start/stop Press MODE for 1 second when the stopwatch is

displayed.During counting the icon ﬂashes.

Reset Press MODE for 4 seconds when the stopwatch is

displayed.

* Start, stop, and reset operations of the stopwatch are performed

separately to measurement, and do not affect other measure-

ments.

* The stopwatch continues counting regardless of the power-sav-

ing state. During counting the icon ﬂashes on every screen

except for the menu screen.

Stopwatch

MODE

Power-saving

screen

Sleep

1 hour

10 minutes

Appendix

SET 4

SET 44

SET

(2/4)

(1/4)

(Press and hold)

24h display

format “Start time” setting

Increase

numbers

12h display format

P (p.m.)

(Press and hold)

Increase

numbers

A (a.m.)

“End time” setting

24h display

format

12h display format

“Illumination

method” setting

(Press and hold)

Night Mode ON/OFF

(Part time)

↔

(Full time)

Night Mode

Set the backlight illumination time and method.

Changing settings [Menu screen]

On the measurement screen, press MENU to go to the menu screen.

Various settings can be changed on the menu screen.

* After changing settings, always press MENU to conﬁrm changes.

* When the menu screen is left on for 1 minute, the computer returns to the measurement screen.

Description

Measurement

screen Menu screen

MODE

MODE MODE

MODE

↔

OFF

MODE

Manual

distance input

Clock

Tire

circumference

Select

measure-

ment unit

Stopwatch

Conﬁrm

(Press and hold)

Change setting

Increase

numbers

12h display format

P (p.m.)

Increase

numbers

A(a.m.)

12h display format

(Press and hold)

Appendix

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de Cateye

Cateye

Cateye CC-CD200N Manual de usuario

Cateye

Cateye CC-VL100 Manual de uso y mantenimiento

Cateye

Cateye Stealth EVO CC-GL11 Manual de usuario

Cateye

Cateye Enduro8 CC-ED300 Guía de configuración

Cateye

Cateye TL-LD170-W Manual de usuario

Cateye

Cateye Padrone+ Manual de usuario

Cateye

Cateye ASTRALE Manual de usuario

Cateye

Cateye STRADA CC-RD100 Manual de usuario

Cateye

Cateye Stadium Light HL-MH310 Manual de usuario

Cateye

Cateye PADRONE DIGITAL CC-PA400B Manual de usuario

Cateye

Cateye ENDURO 2 Manual de usuario

Cateye

Cateye VELO WIRELESS+ Manual de usuario

Cateye

Cateye CC-MC100W Manual de usuario

Cateye

Cateye STRADA CC-RD100N Manual de usuario

Cateye

Cateye TL-LD135-R Manual de usuario

Cateye

Cateye Vectra CC-VT100W Manual de usuario

Cateye

Cateye Urban Wireless+ Manual de usuario

Cateye

Cateye RAPID X2 KINETIC Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

Cateye

Cateye GVolt70.1 HL-EL552G-RC Manual de usuario

Cateye

Cateye MICRO Wireless CC-MC100W Manual de usuario

Cateye

Cateye OS 1.1 Manual de usuario

Cateye

Cateye HL-EL120 Manual de usuario

Cateye

Cateye Micro CC-6000 Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario

Akku Vision

Akku Vision e-bike vision 10046 Guía de inicio rápido

Squire

Squire Inigma Manual de usuario