CAS WEIGHING SOLUTION SWII PLUS Series Manual de usuario

2

3

PRECAUTIONS 4

PREFACE 6

NAMES AND FUNCTIONS 6

OPERATIONS 8

1. Simple Weighing Mode 8

2. Weighing with Tare 8

3. Changing Unit of Weight 9

4. Hold Function 9

5. Comparator Function 10

6. Counting Function 11

7. Setup Mode 14

BATTERY MAINTENACE 15

ERROR MESSAGE 15

SPECIFICATIONS 16

4

5

6

Thank you for purchasing CAS SWΙΙ PLUS series.

These series have been designed with CAS reliability, under rigid quality control

and with outstanding performance. Your special departments can enjoy these

high quality reliable CAS products.

We believe that your needs will be satisfied and you will have proper reliability.

This manual will help you with proper operation and care of the SWΙΙ-W.

Please keep it handy for future reference.

NAMES AND FUNCTIONS

OVERALL VIEW

7

DISPLAY & KEYBOARD

KEY FUNCTIONS

KEYS FUNCTIONS

Used to set the zero point.

Used to convert the unit of weight.

(If you press the button long time, Unit is converted)

Used to input or cancel the weight of tare.

Used to make the weight of commodity stable.

This weight is average value.

Used to change the unit of weight, and shown as following sequence

on the display. [Kg] [WL on or off] [PCS] [Kg]

(If you press the button long time, Mode is changed)

Used to turn on and off the scale.

8

●Turn on the scale by pressing key. Then, the display will show all the

segments and count up "0" to "9". You may stop this automatic counting by

pressing the key.

●When you turn on the display, make sure that platter is empty. Otherwise,

display will show "Err 1", an error of initial zero range. Please refer to "ERROR

MESSAGE" section for more information on page15.

●When the weight becomes stable the display shows the stable sign ( ) on.

●You may need to make it "0.000" by pressing key unless the display

indicate "0.000" under the empty platter.

1. Simple Weighing Mode

①Place a commodity on the platter.

②Remove the commodity from the platter.

2. Weighing with Tare

●TARE means the weight of container being used for a commodity.

●TARE key function is to subtract the weight of the container from full weight loaded

Place a container on①the platter.

9

②Press the key.

③Place a commodity into the container, then

the display will show only the weight of the

commodity.

④Remove container and commodity, then the

display will show the weight of the container

with "-" symbol.

⑤Press the key, then display will

show the "0.000".

3. Changing Unit of Weight

●Press the key a few seconds.

You may select kg, or g as the unit of weight.

4. Hold Function

①When the weight is unstable, press the

key

②Then "HOLD" will be displayed twice

③Then average value will be show twice And

the "HOLD" function will be removed

automatically

10

5. Comparator Function - HI / LOW Limit Setting

①Press the key until the display

shows "WL OFF" (Press the key for a

few second). "WL OFF" means that

comparator function is not activated..

②Press key to activate this function.

The display shows "WL ON".

③Press key once to set up the low

limit. The display shows "0.000" and the first

number flashes..

④Press the key to have number

increase. To move flash to next digit, press

the key.

⑤Press key to set up HIGH limit. The

display shows "2.000" and you can change

these numbers by pressing key.

If you want to move to next digit you can go by

pressing key.

⑥If you set up HIGH limit you can go out by

pressing key, and "End" message on

the display.

⑦If you set up HIGH limit and LOW limit incorrectly, "Err" will be shown on the display. Then

you may need to set it up again. For example, setting LOW LIMIT=2.990 kg and HIGH

LIMIT=1.990 kg this is incorrect setting because HIGH limit is lower than the LOW limit. When

HIGH and LOW limit are set as the same or above maximum capacity it still shows "Err"

message.

11

⑧If you want to go back to the simple

weighing mode just press key twice.

(Press the key for a few second).

⑨Suppose that the HIGH limit and LOW limit

are set up as 2.990kg and 1,990kg

respectively.

If the weight loaded is 2kg between HIGH and

LOW limit the display shows "OK" and the

scale continues to beep slowly.

If the weight loaded is above 2.990kg, HIGH

limit, the scale continues to beep rapidly.

6. Counting Function

●Counting without Tare

①Initial display as above.

②Press key twice to go to sample unit

selection mode. (Press the key for a

few second)

③Press key to select the number of

sample unit. You can select 10, 20, 50, 100,

200, or 500 as a sample unit.

④If you select "P_10" as a sample unit, then

please put 10 sample units on the scale.

Then press key to set sample units.

⑤Put all of commodities you wish to count,

and then check the number of pieces on

display.

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Escala de CAS

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario