CARVIN Vintage 16 Manual de usuario
- 1 -
How to bias:
Vintage 16
Rev C
6/27/2012
carvinservice.com
- 2 -
Only a certified technician should bias Carvin amps, this is very
dangerous, you can get hurt, please be very careful when working
with any tube amp!
If you have changed the tubes make sure they are a matched set. (2) EL84
- The Bias for the Vintage 16 should be 40mA at Power Mode to Normal setting,
with 120VAC.
STEP 1
These are the tools you will need:
1. A flat head screw driver
“small”.
2. A multi-meter, w/ milli amp
reading.
3. Banana to clip leads.
4. Amp stand (optional).
STEP 2
Take the amp out of the amp
enclosure (cabinet). Set it in an amp
stand. Be very careful with the tubes
they can break.
NOTE: If you don't have an amp
stand then support the chassis on
some blocks of wood so that the
power tubes are not touching
anything - they get very hot!
- 3 -
STEP 3
Set the switch to “Internal Load”
IMPORTANT: Do NOT turn on the
amplifier without a speaker plugged
in!", when in 8 or 16 Ohm setting.
STEP 4
Make sure you set the switch in the
back to Normal; if you don’t set it to
“Normal” the bias will not be the true
reading.
STEP 5
A) Lower the volume.
B) Unplug your guitar cord from the
input of the amp.
NOTE: If you have signal going
through the amp, it will not be the
true reading, when you set the bias.
- 4 -
STEP 6
A) Connect the leads to the meter. B) Set your meter to the milliamp (MA) position.
Make sure the fuse inside is good.
NOTE: If the Fuse inside your meter is open, the meter will never work. It will
always read 0mA. In the meter above, mA and COM is selected, you have the
option to plug in the lead on (A) but because the setting will be set to 100mA it is
best to use mA.
STEP 7
Move the wire connected to QC2 to the QC9 spade
connector. In doing this you are opening the circuit so
that you can measure the current across it.
Note how in step 8 (pictures) the wire is already moved.
STEP 8
1. 2.
- 5 -
Connect clips from meter to spade connectors. One of the clips to QC2 and the
other clip to QC9.
IMPORTANT: Never power the amp ON before connecting the leads, you will
get a big spark, you may blow the fuse of the Meter and or damage the amp.
STEP 8
Plug in AC Cord.
NOTE: Sometimes when the AC Cord
is new it does not want to go in all the
way. Push firmly to force it in, if that is
the case.
STEP 9
Turn the Power Button ON. Wait 2
minutes for the amp to get hot, after the
2 minutes you should see the meter read
current. It will start slow then increase
up to 40mA, adjust it accordingly.
- 6 -
STEP 10
Check your meter at this point, if it goes
over 40mA, lower it by turning the bias
potentiometer with the screw driver,
clock wise, if it’s under 40mA bring it
up by turning the potentiometer the
other way.
It is OK and normal for the bias reading
to fluctuate a little bit and may not be
exactly 40mA but as close as possible.
IMPORTANT: I was using a current shunt to measure the current, that’s why the
pictures below shows mV, your meter should read (mA).
Good Bias High Bias Low Bias
STEP 11
Power down Steps:
1. Turn OFF the amp
2. Disconnect the meter leads.
3. Unplug your AC cord and wait for the tubes to cool down, so that you can put the
amp back in the cabinet.
4. Move the wire connected to QC9 back to QC2.
IMPORTANT: During biasing and normal amp operation if there is a burning smell
or loud crackling noise that comes from the speaker, you should turn off the amp as
your may have a bad tube. The same is true if your meter reads higher that 150mA
or goes into overload. The tubes should never glow RED on the gray plate material,
- 7 -
the largest metal part inside the tube. This indicates a major problem and extremely
unsafe condition. If this happens turn off the amp immediately!
IMPORTANT: The tubes get very hot! Don’t touch them, you will burn your
skin if you do. If the amp is ON the tubes will get hot, even if you are not
playing the amp, wait 30 minutes before handling the unit to ensure the amp
cooled down.
IMPORTANT: This is not the only way to set the bias on this amp, this is the
Carvin Approved method which is used on the Production line in the San Diego,
California Factory.
NOTE: If the tubes are getting hot and 3 to 5 minutes went by and you don’t see
any reading on your meter check your meter, you may have the leads plugged into
the wrong place in your meter or the fuse of your meter is open.
EXPORT(230-240VAC 50Hz): Follow the same instructions.
www.carvinservice.com
Comments or questions email us at Carvinservice@carvin.com
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Amplificador de CARVIN
CARVIN
CARVIN F1200 Manual de usuario
CARVIN
CARVIN VL300 Manual de usuario
CARVIN
CARVIN DCM4000 Manual de usuario
CARVIN
CARVIN KB100 Manual de usuario
CARVIN
CARVIN AG100D Guía de inicio rápido
CARVIN
CARVIN QUADX Manual de usuario
CARVIN
CARVIN HD1500 Manual de usuario
CARVIN
CARVIN PB100 Manual de usuario
CARVIN
CARVIN LT Series Manual de usuario
CARVIN
CARVIN BX500 Manual de usuario
CARVIN
CARVIN DCM1000 Manual de usuario
CARVIN
CARVIN DCM600 Manual de usuario
CARVIN
CARVIN HT150 Manual de usuario
CARVIN
CARVIN DCM1540L Manual de usuario
CARVIN
CARVIN STX125 Manual de instrucciones y seguridad
CARVIN
CARVIN FET 1000 Manual de usuario
CARVIN
CARVIN R600 Red Line Series Manual de usuario
CARVIN
CARVIN TN100 Manual de usuario
CARVIN
CARVIN VTX100 Manual de usuario
CARVIN
CARVIN DCM2000 Manual de usuario
